Question about 2000 Nissan Xterra

Open Question

Nissan Xterra Labor cost replace Fan Clutch - 2000 Nissan Xterra

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 420 Answers

SOURCE: clutch release bearing, '89 Nissan D21 p/u, 2.4L eng.

Yes the tranny and bell housing need to be removed. It is a lot of HEAVY work but pretty straight forward.

Posted on Apr 24, 2009

Ad
  • 22 Answers

SOURCE: when to replace timing belt? what's the avg. cost?

I recommend 60-90K Cost depends on the dealerships labor but usually when your doing a timing belt, radiator hoses and fan belts are removed and should be replaced while your in there. Its about 3hrs, more if other things need to be replaced while in there. So you looking at $300+ for labor only

Posted on Apr 27, 2009

localwonder
  • 6784 Answers

SOURCE: 1) Apx. how much would it cost parts & labor to change Ignition switch on a 1998 Nissan Maxima SE? 2) Do you think I can find the parts?

HI, the cost of the ignition switch is $27.99. the labor cost is usually figure by the hour and it is set a 50 dollar an hour increment. In my shop, we have a set minimum labor charge of two hour as most shops in my area. Total estimated cost including the labor and parts should be around $127.99 give or take.

You can most certainly purchase this part yourself on-line at www.autozone.com

Part Number is - LS812
OEM Number---- 48750- 1E411

Please rate and god bless:)

Posted on May 07, 2009

  • 4044 Answers

SOURCE: Labor cost on replacing a automatic transmission

Typically, if you have the replacement transmission it will cost around 800 depending on where you go. I have no data on what the transmission will cost you in your area.

Posted on Sep 01, 2009

SOURCE: HOW TO REPLACE A FUEL PUMP FOR A NISSAN XTERRA


Removal & Installation

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Drain the fuel tank.
  4. Remove or disconnect the following:

    Negative battery cable Fuel pump module harness connectors Filler hose shield Fuel pressure and return lines Filler hose Vent hose Evaporative Emissions (EVAP) hose Fuel tank skid plate Fuel tank Fuel level sender Fuel pump

To install:
  1. Install or connect the following:

    Fuel pump Fuel level sender. Tighten the screws to 17-23 inch lbs. (2.0-2.5 Nm). Fuel tank. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). Fuel tank skid plate. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). EVAP hose Vent hose Filler hose Fuel pressure and return lines Filler hose shield Fuel pump module harness connectors Negative battery cable
  2. Fill the fuel tank.
  3. Start the engine and check for leaks.

Posted on Mar 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loose fan clutch on 2006 xterra


Here's a link Tim with pictures,just stroll down to see.Look's simple. Replace cooling fan clutch Nissan Xterra Forum

Feb 27, 2014 | Nissan Xterra Cars & Trucks

2 Answers

2001 xterra overheating


Hi, you mentioned a clutch fan? I belive they have an elec. Fan. Have that checked.

May 01, 2017 | 2001 Nissan Xterra

1 Answer

2003 Nissan Xterra - Fan noise when a/c on


No that doesn't sound like the problem, the fan clutch locks up to cool the engine off due to the increased load of the AC system on the cooling system, so it locks up and gets much louder. If it didn't lock up the engine would overheat.

Jun 28, 2012 | Cars & Trucks

1 Answer

P0744 code how much will it cost to fix


replacing the tcc will do the trick !! as for how much it will cost. depends on what area and who does it. ( torque converor clutch ).

Jan 18, 2011 | 2002 Nissan Xterra

1 Answer

2004 nissaan xterra v6 3.3L at 4wd; temp gauge starting to run hot. I changed water pump, thermostat and fan clutch at 1st sign. and timing belt and tensioner while i was in there. after replacement, I...


Well , I know $800 is a big bill , but think of it this way , you got a bunch of new stuff on the car. The timing belt replacement alone would cost someone almost $800 to have done by a mechanic , and if it broke and destroyed your engine how much would that have cost. It's always nice to solve the problem on the first try , but at least it is fixed now , and you won't have to worry about any of that other stuff for a long time.

Dec 05, 2010 | 2004 Nissan XTerra

1 Answer

Removal of knock sensor on 2000 nissan xterra v6 3.3


very labor intensive repair.not for a novice. its under the lower intake. way down deep. You dont realy need to replace it unless your xterra is supercharged.

Sep 22, 2010 | Nissan Xterra Cars & Trucks

1 Answer

My 2002 xterra has started running hot..code po 217 came on..after gas cap was put on wrong..cleared code put gas cap on right then fine for 2 weeks..when idleing heat gauge rises high..as soon as i rev...


p0217 is coolant over temperature. the fan clutch may be slipping or the thermostat is bad. changing the thermostat would probably be the easiest and most inexpensive fix to determine the problem.

May 09, 2010 | 2003 Nissan Xterra

1 Answer

Popping and grinding with extreme wheel turns


Hi

This sounds very much like a problem with your front wheel bearings.

The Xterra Wheel Bearings need to be re-greased at least every 30k miles, and more often if you often go through water deep enough to reach the hubs. When the water gets in the hubs it contaminates the grease and damage can be done to the bearings. This will create a grinding noise and in severe cases even damage to the axle spindle.

You will need to have this looked at by a mechanic to fully assess the damage. Cost will very much be dependant on the extent of this damage.

This link gives an idea of the cost for bearings on the Xterra but obviously this does not include labor to fit. As I say the overall cost is difficult to predict until the full extent of the damage is known.

http://www.autopartswarehouse.com/search/?N=0&VN=+4294967085+4294965648+4294967179&Nr=AND(make:Nissan,model:Xterra,part:Wheel+Bearing,universal:0)

Hope this helps. Thanks for using FixYa.

Nov 20, 2009 | 2004 Nissan XTerra

2 Answers

When to replace timing belt? what's the avg. cost?


I recommend 60-90K Cost depends on the dealerships labor but usually when your doing a timing belt, radiator hoses and fan belts are removed and should be replaced while your in there. Its about 3hrs, more if other things need to be replaced while in there. So you looking at $300+ for labor only

Apr 27, 2009 | 2001 Nissan Xterra

1 Answer

AC not blowing cold air


If the compressor is not coming on, the compressor clutch may be bad, or it may have disconnected at the power connector. There is a plug that attaches to the compressor that engages and disengages the clutch-check to see if it is plugged in. It may also be a bad compressor too. Looks like your compressor should cost less than $200 for the part on Ebay, not sure about labor-they'll probably have to drain the system of refrigerant, replace the part, and fill it back up again

. I'm having the same problem with my car at the moment and I'm pretty sure the compressor is at fault. Hope this helps.

Oct 23, 2008 | 2000 Nissan Xterra

Not finding what you are looking for?
2000 Nissan Xterra Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...