Question about 2007 Ford Focus (3 Door) Hatchback

Open Question

Replace inner reinforcement door handle ford focus 2007

How to install reinforcement door latch without breaking it and and changing over the key cylinder

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jaysonemanme
  • 500 Answers

SOURCE: Need detailed diagram of 1998 latch mechanism to remove connections from it

there is no diagram... the latch is also a non-servicable latch, so if your problems in the latch- it needs a latch. i would look more closely at the outside door handle itself as i have seen a few of them break on the E series vans.you may be able to get detailed instructions thru autozone.com or @ autozone. hope this helps and good luck

Posted on May 29, 2009

SOURCE: ford focus door handle

check focusfanatics.com
but basically after you have the panel off there are a couple torx screws to remove.

Posted on Jul 09, 2008

emissionwiz
  • 75807 Answers

SOURCE: key fob not working after battery change ford focus 2006

Try reprogramming it.

1. Turn the ignition from OFF to RUN 4 times within 6 seconds.
2. Turn the ignition OFF. The system will chime to confirm programming mode.
3. Within 20 seconds, press any button on first keyless remote.
The system will chime once to confirm programming.

4. Within 20 seconds, press any button on second keyless remote.
System will chime once to confirm programming.

5. Turn ignition to RUN to exit programming mode.

Posted on May 28, 2009

  • 104 Answers

SOURCE: how to install replacement door handles for 98 ford ranger pickup

remove interior door panel(need special tool to pop plastic clips holding panel to door)with panel off remove plastic film,with window up you should be able to see two 10m nuts-bolts to remove-also have to pop lever off that goes down to door latch

Posted on Sep 19, 2009

moparownr
  • 667 Answers

SOURCE: 99 ford f150 extended door doesn't open

Remove the interior door panel this can be done with the door closed. peel back the moisture barrier, look inside the door and you will see a latch mechanism with two cables next to it, the top cable releases the top latch and the bottom cable releases the bottom latch, the top latch cable is probably not mounted to the latch (anchored) you will probably have to replaace it with a new one, then it should work fine. Hope this helps, let me know

Posted on Dec 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove inside rear door panel on fiesta 2015


Ford Fiesta Plastic Interior Door Panel Removal Guide ...

www.paulstravelpictures.com/Ford-Fiesta-Interior-Door-Panel-Removal-...
Ford Fiesta Interior Door Panel Removal Guide How to take off the plastic interior door panels in a 6th generation 2009-2015 Ford Fiesta to upgrade the ...

Ford Fiesta inner door panel removal (I removed the top one ...

www.fiestafaction.com/.../44959-Ford-Fiesta-inner-door-panel-removal-...

Jan 19, 2015 - 10 posts - ‎3 authors
This is an excerpt from the manual: Remove the rear door window glass. ... Route theinterior door handle cable and door lock actuator electrical connector through the ...Last edited by WildmaninME; 01-19-2015 at 07:41 PM.

Ford - door panel removal - fiesta - YouTube

? 2:19
https://www.youtube.com/watch?v=1URT13Yusjg
Oct 19, 2013 - Uploaded by one2three
this is the removal of a door panel from a ford fiesta 2001. ...Replacing Broken Inside Door Handle on 2007 Ford Fusion - Duration: 5:32. ... Ford Fiesta 1.25 2004 - Cleaning and adjustingrear brake drums - Duration: 8:47.

How To: 2012+ Ford Focus Rear Door panel removal(SE,ST ...




Jan 13, 2016 | Cars & Trucks

1 Answer

2001 focus LR latch wont let door open. no child locks .outside handle limp inside handle sound like latch is being pulled how can i get the door open?


It would seem there is nothing else to do other than remove the door panel with the door closed. Removing the seat is likely to be necessary.
Not always possible to remove the door card without damage.

Welcome to my world...

Oct 06, 2015 | 2001 Ford Focus

1 Answer

Rear door will not open on my ford focus ghia t reg


Hi chance are the mechanism inside door jamming. Short of forcing off the inner panel in order to clean lubricate etc I find the best way to get this open is to get someone to keep activating your central locking open and shut while you simply keep trying the door handle at the same time and this can some times just catch the latch in just the right position to get the door open ( you dont need to forcefully be pulling on the handle as the latch will either simply click over on the fine spring latch mechanism or not force is not going to help).
Once and if you manage to get door open take off the inner door card panel and oil lubricate mechanism. rather than then shut door simply use a screw driver on latch to test and worth then working back and forth. If still jamming replace latch.

Dec 01, 2013 | Cars & Trucks

1 Answer

2006 Ford Focus ZX4: Front passenger door handles do not engage, both inside & out, no resistance at all. Any exploded diagrams available to show what parts needed & how to...


the plastic clip that holds the door release rod on the latch is either broken, or fallen off, to fix this you need to remove the inner door panel, there will be screws along the door handle puller, and inside the little door cup, also on the inner door handle there's one, if you have mechanical windows there's a clip that holds that handle on, remove it with a small flat head screw driver, ( watch out they tend to fly off ) once the screw is off the door handle, pop it out towards you, and remove the rod and clip attached to it, once all the screws are removed,, take a putty knife, along the bottom of the panel and pop out the clips that hold this in place slide the panel up to get it off the window rail at the top of the panel,, now once inside your going to see a sheet of plastic, peel it back , look inside the holes in the door for a rod thats come off ,, once you locate the outer door handle,, you will see where the clip and rod go on one end or the other,,

Aug 26, 2011 | 2006 Ford Focus

1 Answer

Install door latch cable


Technical Instructions
See picture below
1. Remove door trim panel and water shield per
NOTE: Place a strip of masking tape along the edge of door before removing trim panel to prevent scratching the door with the trim panel removal tool.

2. Snap cable housing end from slot on inside door handle assembly and disconnect cable.
NOTE: Use care to prevent bending of cable housing retainer bracket.

3. Remove rear window channel retaining bolt to allow access to door latch.

4. Position a block (screwdriver handle) between the latch and the door inner panel and snap the cable housing end out of slot (towards inner panel) on door latch assembly and disconnect cable at latch.
NOTE: Use care when removing cable housing to avoid bending of the latch. Discard cable.

5. Hook up new cable at latch and snap cable housing end into slot.
NOTE: Make sure the cable housing is fully seated in the slot.

6. Apply a light film of Teflon grease to the barrel end of the cable. See Figure A.

7. Install return spring. See Figure A.
NOTE: Ensure that the push button rod is located between the spring and the door inner panel.

8. Install foam block at latch. See Figure A.

9. Position water shield over the return spring and install push pin to retain upper portion of water shield. See Figure B.
NOTE: Push pin goes in the same hole as the return spring.

10. Clean hands of grease before performing step 11.

11. Remove protective backing along the lower edges only of the water shield. See Figure A.

12. Install latch water shield at door latch. Pinch the exposed adhesive surfaces together to secure the water shield. Check to insure water shield is not showing through the door shut-face latch access hole. See Figure B.

13. Attach cable to inside door handle assembly and snap cable housing into slot.
NOTE: Make sure the cable housing is fully seated.

14. Check the gap as shown in remote control using a 3/16 drill bit shank end. The drill bit shank should fit in the gap without any clearance and a tight fit is preferred. See Figure C.

15. If the drill bit is too loose or does not fit, adjust by bending the cable bracket as required.

16. Place plastic wedge on remote bracket as shown. Wedge must fit with at least a light press fit for retention. See Figure D.

17. After installation, Apply a dab of special Teflon grease, supplied with the service cable to cable housing openings at inside handle end. The grease should surround and contact the cable all the way around, to seal the opening between the cable and the cable housing.

18. Check all latch functions to insure correct assembly of latch system. If the inside handle does not release properly, replace the inside handle remote release mechanism.

19. Reposition and install trim panel using new push pins if required.


emissionwiz_53.jpg

Dec 07, 2010 | 1993 Ford F250

2 Answers

How to install outer door handle of Ford Focus


remove inside door panel, remove bolts/screws of old door handle, install new handle

Sep 30, 2010 | Ford Focus Cars & Trucks

1 Answer

Focus v reg ( Jan 2000 ) GHIA 2litre not hatchback. Trouble with central locking. all doors lock except passenger door. None of doors would lock until I disconnected Passenger door lock Cannot get lock...


Best way is to turn the key quarter turn to allow the rods to move over. The lugs tend to break when removing doors locks, so best order a couple before attempting to re-fit.
Kind regards

Oct 20, 2009 | 2000 Ford Focus

1 Answer

How do I replace the passenger side mirror on a 2007 ford focus?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Apr 12, 2009 | 2007 Ford Focus (3 Door) Hatchback

Not finding what you are looking for?
2007 Ford Focus (3 Door) Hatchback Logo

Related Topics:

464 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...