Question about Cars & Trucks

Open Question

Diagram to replace thermostat for 95 chevy corsica 3.1liter V6

What should be removed to replace thermostat

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Molson02536
  • 3854 Answers

SOURCE: thermostat location

The thermostat is in a difficult position. Follow the upper radiator hose and it leads into the block under the throttle body. 
Remove the air filter assembly and you'll c what is the exhaust manifold crossover pipe right in front of the thermostat housing.
 NICE, it gives you very little room to remove the 2 bolts to the housing and once u remove those then you'll find you have the thermostat housing loose but because of that darn exhaust manifold crossover pipe u don't have enough room to take the thermostat housing out to change the stinking thermostat. 
So from what you can see, you have to remove the heat shield which is cased around the exhaust manifold crossover pipe and if you still can't get enough room to remove the thermostat, (which you amy find out)then you'll have to remove the crossover pipe as well just to change the thermostat. 
If you have to remove the crossover pipe then their are 2 bolts on both ends of the pipe leading into the manifolds. But then the tough parts done and once u switch the thermostat over and ATTENTION:remove any old gasket material and put a new gasket in it's place then installation is reverse of removal. 
Good luck and hope this helps,

Posted on May 08, 2009

  • 337 Answers

SOURCE: remove and replace alternator for chevy corsica 1993

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800a719b

Posted on Dec 03, 2008

  • 1 Answer

SOURCE: 1996 Corsica - how to remove alternator

you have to undo the belt by lifting on the tensioner which located on the below the power steering pump you may have to remove the motor mount bolts (make sure you suport the motor use a piece of wood so you dont crack oil pan) once you remove the belt look behind the alternator, mine had a hood connected to the cowl that comes of easy unhook the two wires (one is a plug with alittle clip the other is on a bolt held on by the nut) find the bolt on the alternator towards the front of the car remove that bolt and the brace it goes into there is another little black brace that comes off the back and goes to the manifold the next bolt is towards the back it is a long bolt that goes all the way though this one is a pain to remove and put back once you have them out is should come out i had to wiggle mine some then just do it backwards to reinstall

Posted on Mar 09, 2009

  • 26 Answers

SOURCE: How do I replace the thermostat in a 95 chevy Beretta 3.1 v6

you need a socket and a swivel to reach it, the bottom hole in housing is slotted so you won't need to take the bolt all the way out.

Posted on Jun 25, 2009

c17hydro
  • 2984 Answers

SOURCE: How do I replace a side mirror chevy corsica?

Please don't forget to rate....thanks:


Removal & Installation The door outside mirrors are stud mounted to the door filler. The mirror glass face may be replaced by placing a piece of tape over the glass then breaking the mirror face. Adhesive back mirror faces are available. Left side flat and right side convex mirror faces must be replaced with the same type mirror face when surfaced.

  1. Remove the door trim panel.
  2. Remove the upper trim panel.
  3. Remove the sound absorber.
  4. Remove the (3) nuts.
  5. Remove the control cable from the upper trim panel.
  6. Remove the filler and mirror.
To install:
  1. Place the filler over the studs on the mirror.
  2. Install the control cable through the filler and connect to the upper trim panel.
  3. Install the (3) retaining nuts and tighten to 42-72 inch lbs. (4.7-8.1 Nm).
  4. Install the sound absorber, upper trim panel and trim panel.

Posted on Mar 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 95 Chevy Corsica and it only cuts off wen it's hot outside. What could be the reason for that thermostat doesn't goes past the half way point. But once it get cool it cranks up and drive away


First you will need to find out if you are loosing spark or fuel when it stops running. Could be a weak fuel pump, or ignition module among other things.

Jun 16, 2015 | 1995 Chevrolet Corsica

1 Answer

Where is the thermostat located on 1994 corsica Chevrolet 3.1 v6


Follow the top hose from the radiator to under the throttle body. I remove the throttle body for access.

Mar 07, 2015 | 1994 Chevrolet Corsica

1 Answer

Having a promblem taking off crossover exhaust pipe on a 2005 Buick rendezvous I tooken off the two front exhaust Then took bottom two bolt . But still fasten to something is there other bolts...


Thermostat? engine cooling?
2 engines, here, LYA adn LY7.
nobody here posts engine, why do that?
so ill post only for 1.
the LA1
here are the steps.
NO FSM Sux huh? nor an alldata.com account, why not that? 15 bucks?


STAT out.
Remove the air cleaner and duct assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls - 3.4L.

Drain the coolant until the coolant level is below the thermostat. Refer to Cooling System Draining and Filling (Refer To List 1) .

Remove the crossover exhaust pipe. Refer to Exhaust Crossover Pipe Replacement (Refer To List 2) in Engine Exhaust.

Remove the radiator hose from the thermostat housing.

Remove the thermostat housing bolts and clean any sealer from the bolt threads.

Remove the thermostat housing and gasket.
remove STAT
next is crossover page.

Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnection and Connection (Refer To List 1) in Engine Electrical.

Remove the throttle body air inlet duct.

Drain the coolant from the cooling system. Refer to Cooling System Draining and Filling (Refer To List 2) in Engine Cooling.

Remove the inlet radiator hose from the engine. Refer to Radiator Inlet Hose Replacement (Refer To List 3) in Engine Cooling.

Remove the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Engine Cooling.



Remove the exhaust crossover heat shield bolts.

Remove the exhaust crossover heat shield.
  1. Remove the exhaust crossover pipe studs/nuts.
  2. Remove the exhaust crossover pipe.

end , remove.

now the bypass pipe FWD cars SUCK
  1. Disconnect the left engine mount strut from the engine.
  2. Remove the heater hose from the bypass pipe.
  3. Remove the thermostat bypass pipe to throttle body nut.
  4. Use the J 38185 in order to remove the thermostat bypass pipe hose clamps (1,5).
  5. Remove the thermostat bypass pipe to cylinder head nut (3).
  6. Remove the thermostat bypass pipe bolt (4).
  7. Remove the thermostat bypass pipe hose.
  8. Remove the thermostat bypass pipe.
sigh.....
why not log in to alldata.com
read the page then ask ques tons that are not clear.
and next time post the engine type.
above is just 1 engine.

Jun 18, 2014 | Cars & Trucks

1 Answer

Removing the middle console in a 95 Chevy Corsica


look for the screws at the base of the console.. you may need the key in the ignition to move the shifter so the cover can be moved.. the seats may need either forard or back to acess these screws..

Jan 01, 2014 | 1995 Chevrolet Corsica

1 Answer

Replace thermostat in a 1997 Dodge Intrepid


The thermostat is an easy replacement. The part from the part store should be very inexpensive and is very easy to install. IMPORTANT: allow the cars cooling system to completely cool down before starting to work on it. Here are the steps to replace the thermostat:

1. Allow car to cool.
2. Place drain pan under radiator and allow for coolant to drain below the thermostat. Do not completely drain the system unless replacing the fluid.
3. Remove the hose clamp and hose from thermostat housing.
4. Remove the two bolts holding the housing to engine.
5. Remove the thermostat gasket and clean the gasket completely off the engine and thermostat housing.
6. Remove the thermostat and replace with new.
7. Place new gasket on with reassembly.

Oct 12, 2013 | 1998 Dodge Intrepid

1 Answer

How to take rotors off 95 Chevy Corsica


http://www.2carpros.com/articles/how-to-replace-front-brake-pads-and-rotors-fwd

Autozone.com as some good info as well. Thats where I got mine. I'll be doing this project myself soon...maybe we can learn together :-)

May 15, 2012 | 1995 Chevrolet Corsica

2 Answers

I need to replace my 95 chevy corsica transmission do i have to take out the engine


the trans is removed through the bottom with the engine left in

Jul 27, 2011 | 1995 Chevrolet Corsica

1 Answer

How to get the thermostat housing to disconnect. We have taken all bolts loose but will not come apart.


Not sure if you have the 2.7L or the 3.5L so I'll post for both sizes for you:


2.7L Removal procedures
  1. Drain cooling system.
  2. Remove radiator lower hose from thermostat housing.
  3. Remove nuts from heater tube flange studs.
  4. Loosen starter bolt at heater tube bracket.
  5. Pull heater tube out of thermostat housing and position out of the way.
  6. Remove bolt and two studs.
  7. Remove thermostat housing, O-ring and thermostat.
  8. Remove thermostat housing bolts.

3.5L Removal procedures

  1. Drain cooling system.
  2. Raise vehicle on hoist.
  3. Disconnect electrical connectors from engine oil and power steering pressure switches.
  4. Disconnect radiator and heater hoses from thermostat housing.
  5. Remove thermostat housing bolts.
  6. Remove housing, thermostat, and gasket.
NOTE:
The OEM thermostat is staked in place at the factory. To ensure proper seating of replacement thermostat, carefully remove the bulged metal from the thermostat housing using a suitable hand held grinder. It is not necessary to restake the replacement thermostat into the thermostat housing

May 07, 2011 | 2003 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

285 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...