Question about 2006 Chrysler 300

Open Question

Flow control valve replacement on a chrysler 300

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Code P0406

Where is the egr valve on my crystler 300?

Posted on Aug 17, 2009

  • 25 Answers

SOURCE: eng. light came on my 2005 chrysler 300. code came

it should be arond the throttle body and might have two to 4 screws in it

Posted on Nov 25, 2009

c17hydro
  • 2984 Answers

SOURCE: need to replace a idle air control valve on a 1999 300M Chrysler

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Disconnect the IAC electrical connector.
  3. Remove the IAC mounting screws.
  4. Remove the IAC.



da3669e.gif

To install:
  1. Install the IAC to the throttle body.
  2. Tighten mounting screws to 5.1 Nm (45 inch lbs.) torque.
  3. Attach electrical connector to the IAC.
  4. Connect the negative battery cable.
  1. Disconnect electrical connector from IAC motor.
  2. Disconnect air plenum (where applicable).
  3. Remove two mounting bolts (screws).
  4. Remove IAC motor from throttle body.

3ccd55e.gif

To install:
  1. Install IAC motor to throttle body.
  2. Install and tighten two mounting bolts (screws) to 60 inch lbs. (7 Nm) torque.
  3. Install electrical connector.
  4. Connect air plenum (where applicable).

Posted on Mar 06, 2010

MNfisherman
  • 11896 Answers

SOURCE: How do you replace the egr valve on a 300

Heat up the exhaust pipe to egr with torch and spray with knockitloose or wd40 when not hot. Then remove that pipe. Then remove vacuum hose and the 2 bolts that hold it on.

Posted on Mar 31, 2010

ml85
  • 67 Answers

SOURCE: How much would it cost to replace engine valves on

Depends on whether you are doing the work or a shop doing the work. If you are doing it, it's the cost of the valves, head gaskets and whatever else you need. If the shop is doing it, call them for an estimate.

Posted on Feb 29, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Orifice tube location on a 2002 chrysler 300m


2002 Chrysler 300 has an expansion valve instead of an orifice tube which is used to meter the flow of refridgerant. It is located on the firewall attached to the AC manifold hose assembly 4e13a00d-e237-447d-9c7e-ef4684c71d0b.jpg 452a74e8-1d11-479f-9e19-3d118dc43633.jpg

#10 is expansion valve and #3 is the hose assembly..follow AC hoses from compressor to the firewall and it will take you to the expansion valve

Jul 13, 2014 | Cars & Trucks

1 Answer

Code p2017 on a chrysler sebring


Here is the definition.

P2017 CHRYSLER - Intake Manifold Runner Position Sensor/Switch Circuit High Bank 1

Possible causes - -
- Manifold flow valve harness is open or shorted
- Manifold flow valve circuit poor electrical connection
- Faulty Manifold flow valve
- Faulty Powertrain Control Module (PCM)

You'll need someone with a shop manual to get the testing procedures.

Apr 14, 2013 | 2007 Chrysler Sebring Sedan

1 Answer

I have replaced the the Thermostat on my Chrysler 300 with the 5.7 Hemi Engine. It still over heats. Is there more than one thermostat on thi engine?


You didn't state when it overheats, if it is while driving the fault can be : belt driving water pump slipping , lower radiator hose collapsing, most common is clogged radiator. Start the engine with the radiator cap off when it is COLD and observe the flow in side. If you see really fast flow of coolant you have the bottom portion of the radiator stopped up. The only way to know is to remove the radiator and have it flow tested.
A blown head gasket or cracked head will cause steam to come out of the exhaust, water in the oil (milky). If it is running hot while idling , check fan to see if it is turning as it should when it should. Older cars have fan clutches that go bad, newer ones have temp thermostats that go bad.

Apr 30, 2017 | Chrysler 300 Cars & Trucks

1 Answer

2008 chrysler 300 heater/ac control only changes functions when fan is on high


sounds like a electrical issue in the switchs there not flashing a trouble code are they

Nov 20, 2011 | 2008 Chrysler 300

2 Answers

Where is the egr valve locatedin the 2005 chrysler 300 limited


Your EGR valve is located inthe back of your engine. Take a look at your Intake Manifold... you will see an Iron Rod going from the back of your intake manifold ...downwards in the back of your engine. That rod connects directly to your EGR Valve.
It is fairly easy to replace.

Apr 12, 2010 | 2005 Chrysler 300

1 Answer

How do you replace the egr valve on a 300


Heat up the exhaust pipe to egr with torch and spray with knockitloose or wd40 when not hot. Then remove that pipe. Then remove vacuum hose and the 2 bolts that hold it on.

Mar 31, 2010 | 2005 Chrysler 300

2 Answers

Code P0406


Where is the egr valve on my crystler 300?

Apr 10, 2009 | 2005 Chrysler 300

2 Answers

Engine Light On - 2006 Chrysler 300 3.5 engine


I have a 2005 Chrysler 300. The engine light comes on from time to time -- sometimes it will stay on for a week or so and then go off for at most a day or two. I had the code read yesterday and the feedback was "EGR pressure flow is low." My car has about 65K miles. Is this a typical problem with this car? I was told replacing the EGR valve would fix the problem. How easy is it to replace an EGR valve on this vehicle? Once replaced, do I need to reset the computer --- if so how do I do this? If it is easy to fix, could you please provide step by step directions and show me location of the part in question that needs replaced?

Mar 30, 2009 | 2005 Chrysler 300

Not finding what you are looking for?
2006 Chrysler 300 Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...