Question about Buick Lucerne
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Changing Headlight bulb
okay it is actually really easy althought they wouldn't want you to think so. It took me and my husband like 3hours to figure it out. But we did and now were like duh. If you open your hood and stick you hand down the front to where you are right behind the headlight if you feel around you will find that there are like caps over the place where you should be able to get your bulbs out. what you have to do is get a small flat head screw driver and pri the cap off and take out your bulb. It sounds worse than it is i promise and the only hard part is getting your hands on the caps
Posted on Nov 19, 2008
Ok yourgoing to want to pop the hood and you will see the back of the light give it a turn counterclock wise and it should pop right out. Then the bulb will just swap over no issues
Posted on Oct 02, 2009
Removing the bulb in a CX7 is a real PITA. If replacing the right bulb, turn the steering wheel all the way to the right, or do the opposite for the left side. (or you can opt to remove the entire wheel on the corresponding side) You'll need to remove 3-4 of the fender well clips with a phillips screwdriver being careful not to break them. Once the screws are removed, pry back the wheel well cover to access the back of the headlamp to change the bulb.
Posted on Feb 01, 2010
The bright light fitting is the same as the dim so take it apart fist to see how the cover screws off/on and the light comes out. Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise. Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light. On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again. Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw. Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket. You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough. If not, then you need to release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit. To remove these locking pins, pull or pry up the little tab in the center of the pin just like you were pulling a nail by the head. That should give you a little more space.
Posted on Apr 03, 2010
The relay under the hood may have gone out. We had the same problem on our 2007 Buick LaCrosse CX. The bulbs were fine, high beams worked, all turn signals and everything except the low beams turned on. Turns out the relay had gone bad.
Posted on Sep 07, 2010
Tips for a great answer:
Aug 29, 2015 | 2006 Buick Lucerne
Aug 21, 2015 | 2006 Buick Lucerne
Aug 08, 2015 | 2007 Buick Lucerne
May 01, 2015 | 2006 Buick Lucerne
Jul 12, 2011 | 2007 Buick Lucerne CXS Sedan
Sep 07, 2010 | 2007 Buick LaCrosse CXL Sedan
Feb 15, 2010 | 2006 Buick Lucerne
Dec 28, 2009 | 2006 Buick Lucerne
95 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: