Question about Chevrolet Corsica

Open Question

What is the bolt torque for 2009 hhr ecotec harmonic balancer bolt

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 87 Answers

SOURCE: Harmonic balancer bolt direction for loosening??

CCW , and your going to at least put the new timing belt on and balance to check for compression. you can run an engine without the covers installed or accessories hooked up

Posted on Feb 07, 2009

Ad
  • 2 Answers

SOURCE: I removed the harmonic balancer bolt, but cant get pulley off.

yes you can get a puller at any local parts store or harbor freight to pull it off

Posted on Mar 25, 2009

  • 150 Answers

SOURCE: cant take off main bolt to harmonic balancer

Using a long 1/2in breaker bar or ratchet of good quality and a socket, place socket on bolt and position ratchet or breaker bar so that the end rests on the frame or the ground on the DRIVER side . Make sure you have the ratchet in the "off" position and turn the ignition to the start position for a split second while someone else holds the rathet or bar on the bolt. This will break the bolt loose, and if the engine starts when turning ignition to start for a split second it will simply unscrew the bolt all the way. If the starter isn't strong enough to break it loose the first time move the ratchet or breaker bar away from it's resting point just a little bit so that it has to travel slightly before hitting the frame or the ground and this WILL break the bolt loose. "VERY IMPORTANT" make sure end of ratchet or breaker bar is is on TOP of the frame or on the ground on the DRIVER side. Glad to help.

Posted on May 23, 2009

  • 8 Answers

SOURCE: What is tightening torque of harmonic bal. bolt 1990 Honda Accord

1990 Honda accord
L4 2156cc 2.2ltr engine
crankshaft pulley bolt
apply engine oil to threads (a few drops)
tighten to 159 ft lbs
please rate my answer as I am new
Thanks,
Chris

Posted on Aug 29, 2009

Testimonial: "Thanks for your answer. 159ft-lbs seems a bit high. I only say this because 1990 Honda Integra 1.8L is 130ft-lbs. Maybe because of bigger engine."

co7196
  • 3433 Answers

SOURCE: cannot remove harmonic balancer bolt on 96 honda (2.2L)

You may need an impact gun. If loctite was used, you will need a gun.

Posted on Sep 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for the harmonic balancer on a 1994 buick roadmaster


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Oct 18, 2016 | 1994 Buick Roadmaster

1 Answer

1995 GMC Suburban 6.5L diesel crankshaft harmonic balancer bolt tourque?


from 98 GM manual crank balancer bolt 270Nm or 200' lbs
crank pulley bolts 50Nm 0r 37' lbs

Copied from this site;
Harmonic balancer torque value Diesel Place Chevrolet and GMC Diesel Truck...

Hope this helps.

Feb 24, 2015 | GMC Cars & Trucks

1 Answer

How to replace crankpully on 3300 olbs


The harmonic balancer on these engines is now press fit onto the crankshaft and requires the use of Tool J-38197 for removal. The torque specification to be used during installation has also been revised. The procedure to be used when replacing the crank sensor is as follows:

REMOVAL






  1. Disconnect serpentine belt from crankshaft pulley.


  2. Raise vehicle on hoist.


  3. Remove right front tire and wheel assembly.


  4. Remove right inner fender access cover.


  5. Using 28 mm socket, remove crankshaft harmonic balancer retaining bolt.


  6. Remove crankshaft harmonic balancer using Tool (J-38197).


  7. Remove foreign object deflector (DO NOT use pry bar).


  8. Disconnect sensor electrical connector.


  9. Remove sensor and pedestal from block face.


  10. Remove sensor from pedestal




INSTALLATION






  1. Loosely install crankshaft sensor on pedestal.


  2. Position sensor with pedestal attached on Tool J-37089.


  3. Position tool on crankshaft.


  4. Install bolts to hold pedestal to block face, torque to (18-26 lb. ft.).


  5. Torque pedestal pinch bolt to (26-44 lbs. in.).


  6. Remove Tool J-37089.


  7. Install foreign object deflector.


  8. Place Tool J-37089 on harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.


  9. Install balancer on crankshaft.


  10. Apply thread sealer GM #(NNN) NNN-NNNNor equivalent to threads of crankshaft balancer bolt. Torque bolt to + 56 degrees (104 lb. ft. + 56 degrees).


  11. Install inner fender shield.


  12. Install tire and wheel assembly. Torque lug nuts to (104 lb. ft.).


  13. Lower vehicle.


  14. Install serpentine belt.
see this vedio

Jul 11, 2014 | 1993 Oldsmobile Cutlass Ciera

2 Answers

Had my Harmonic Balancer replace now it shuts off after 10 mins of it being on


the garage may have did something to the crank position sensor that is located behind the harmonic balance. there is a ring gear there to for the timing

Oct 30, 2012 | 2001 Pontiac Grand Prix

1 Answer

Need torque settings for front calliper bolts on 2009 Chevy HHR


ive done millions of brakes and callipers not once have i torqed to specs on cllipers just tighten till its tough but not to hard or youll snap a bolt..

Sep 29, 2012 | 2009 Chevrolet HHR

1 Answer

I need the location of the harmonic balancer on my 2.2l Ecotec engine. Car is 2004 Chevrolet Cavalier LS.


CRANKSHAFT PULLEY IS THE HARMONIC BALANCER.YOU NEED THESE TOOLS TO REMOVE HARMONIC BALANCER, YOU NEED HARMONIC BALANCER REMOVER AND INSTALLER TOOL.YOU NEED A LARGE PIN SPANNER WRENCH TO HOLD HARMONIC BALANCER IN PLACE WHILE LOOSEN THE HARMONIC BALANCER BOLT.

May 21, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

How do i remove harmonic balancer & replace


YOU NEED A HARMONIC BALANCER PULLER TOOL AND A 15M SIX POINT SOCKET TO REMOVE HARMONIC BALANCER BOLT.TURN OFF RADIO AND REMOVE THE DRIVE BELT AND REMOVE THE NEGATIVE BATTERY CABLE. REMOVE THE STARTER SO YOU CAN PUT A LARGE SCREW DRIVER OR LARGE PUNCH TO STICK IN ONE OF THE FLY WHEEL HOLES TO KEEP ENGINE FROM TURNING WHEN YOU LOOSEN THE HARMONIC BALANCE BOLT. ALSO SCREW DRIVER AND PUNCH CAN KEEP ENGINE FROM TURNING WHEN REMOVER THE HARMONIC BALANCER. YOU WILL NEED A HELPER TO HOLD PUNCH OR SCREW DRIVER WHILE YOU LOOSEN THE BOLT. YOU CAN GO TO SEARS OR ANY AUTO PARTS STORE AND BUY HARMONIC BALANCER PULLER.TORQUE HARMONIC BALANCER BOLT TO 76 FT LBS.

Apr 23, 2011 | 2003 Pontiac Montana

1 Answer

How do you replace the harmonic balancer pulley on the 2000 oldsmobile intrigue


The short answer to your question is:

1. Raise the car on the passenger side and remove the front wheel.
2. Remove the belts on the harmonic balancer.
3. Remove the retaining bolt.
4. With a puller, jack the harmonic balancer off of the crank shaft. You can rent a puller at your local auto parts store. It is easiest to access the harmonic balancer through the fender, hence the need to remove the wheel.
5. You should also consider replacing the seal around the harmonic balancer to minimize the possibility of a leak later.
6. Install the new harmonic balancer and tighten the retaining bolt to the specified torque (I don't know this off the top of my head).
7. Replace the belts and wheel, and voila...mission accomplished.

This was a short answer to your question. You may wish to consult a repair manual for illustrations, torque specifications, additional instructions, etc. This job is not for the faint of heart. Good luck!

Feb 19, 2010 | 2000 Oldsmobile Intrigue

1 Answer

Crankshaft Position Sensor and Camshaft Position Sensor


REMOVE OR DISCONNECT

  1. Serpentine belt from the crankshaft pulley.
  2. Raise the vehicle on a hoist.
  3. Right front tire and wheel assembly.
  4. Right inner fender access cover.
  5. Using a 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Crankshaft harmonic balancer using tool J 38192 or equivalent.
  7. Sensor electrical connector.
  8. Foreign object deflector.
  9. Sensor and pedestal from block face.
  10. Sensor from pedestal.
INSTALL OR CONNECT:

  1. Loosely install the crankshaft sensor on the pedestal.
  2. Position the sensor with pedestal attached on special Tool J 37089.
  3. Position the special tool on the crankshaft.
  4. Bolts to hold the pedestal to the block face, torque to 20-40 Nm (14-28 lb.ft).
  5. Torque the pedestal pinch bolt to 3-4 Nm (38-40 lb.in).
  6. Remove special tool J 37089.
  7. Place the special tool 37089 on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.
  8. Balancer on the crankshaft.
    • Apply thread sealer (GM 1052080) or equivalent to the threads of the balancer bolt.
  1. Torque the crankshaft bolt to 140 Nm + 56°(104 lb.ft + 56°).
  2. Foreign object deflector.
  3. Electrical connector.
  4. Inner fender shield.
  5. Tire and wheel assembly, torque to 140 Nm (104 lb.ft).
  6. Lower the vehicle.
  7. Serpentine belt.

Jun 02, 2009 | 1994 Buick Regal Gran Sport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...