Question about Cars & Trucks

Open Question

05 isuzu npr brake pedal goes to floor first time and then good pedal after that unless there is a little time betwwen using brakes again

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 109 Answers

SOURCE: Brake pedal goes down to floor. Putting brake fluid doesn't solve problem. Vehicle must coast to a complete stop.

First look for obvious leaks under the vehicle, especially the inside area of each wheel... If you see fluid, you have either a blown cylinder seal or a bad line (check the rubber hoses to the front and back brakes too) Repair the offending part and bleed the air out of the system... (remember to clean pads or shoes if they have fluid on them)... If you see no hint of leakage anywhere, then suspect the master cylinder... if you remove the master cylinder, check and make sure that it didn't leak fluid into the brake booster diaphragm (Brake fluid will destroy the booster)... as in any repair when you open the system (lose fluid), you will need to bleed out the air to restore function... hope this helps...;-)

Posted on May 04, 2009

Ad
  • 4 Answers

SOURCE: parking brake pedal goes to floor

The disc brake pads are NOT used for the parking brake. The parking brake uses mini-drum type shoes inside the rear disc rotor.

Take a look at http://wiki.answers.com/Q/How_do_you_change_the_emergency_brake_pads_on_a_2000_Chevy_1500_Silverado_Pickup

For more info

Posted on Jun 21, 2009

emissionwiz
  • 76691 Answers

SOURCE: brake pedel pushes to the floor

pump the pedal about 10 times and see if it comes back up, u need to pump the caliper pistons out after a brake job.

Posted on Jun 27, 2009

litoshop
  • 298 Answers

SOURCE: brake pedal goes down to far abs brakes

Hi I'm litoshop if you bled the system and get no results then your brake pump needs to be replaced now before replacing make sure your pads are installed correctly because if there not this to can cause this problem good luck. if this information has been useful please let us know thank you.

Posted on Aug 11, 2009

  • 3 Answers

SOURCE: 2000 isuzu npr

if you have already replaced the booster, it is probable that the vacuum pump is the culprit.

Posted on Dec 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix brakes that goes to the floor after i replaced the master cylinder


You must have air in the brake lines. You will have to bleed the lines to get the air out. You will have to locate the bleed valve near each wheel. It is easier to take off the wheel so you can see everything. The brake line will have a drain screw near the place that the line goes into the brake caliper assembly. You will need a helper. Loosen the screw a bit then have your helper press the brake to the floor. Fluid and/or air will come out. While they hold it to the floor, tighten the screw so it won't such air back in when the brake peddle is released. With the brake pedal released, open the drain screw again and have the helper press the brake to the floor again. Repeat this until no more air comes out when the brake pedal is pressed. Then move to the next wheel and repeat. During the process make sure that the fluid in the master cylinder does not run out. The level will drop each time you bleed some of it from the bleed valve (or drain screw or whatever you want to call it). It helps to open the drain screw just enough to let a little fluid out. You won't waste as much that way. By time you get through with the last wheel the brake should not go to the floor anymore.

Mar 12, 2015 | 1997 Toyota Corolla

1 Answer

Brake pedal goes to floor when engine running but is fine when engine off


bleed the brakes again starting at the longest line at the rear and work forward . The indication is still air in the lines.

Feb 05, 2015 | 2002 Saturn SC

1 Answer

2006 isuzu npr 5.2L Diesel


Slider pins should be replaced and antilock mechanisms cleaned with brake cleaner. If that doesnt help then its calipers. And yes they do stick at the same time if they both have sat for a long time. Good luck!

Oct 17, 2013 | Isuzu Cars & Trucks

1 Answer

Brake problem isuzu trooper brake pedal goes solid half way down and braking very poor


your master cylinder is gone. when stopped apply pedal and hold let up slightly then reapply if pedal sinks to floor master is bad

Apr 12, 2013 | 1989 Isuzu Trooper

1 Answer

When bleeding brakes have good pedal with engine off. with engine running pedal goes almost to the floor what is wrong


can you here a hissing sound when you push the brake while its running? if so then you have a bad brake booster, need to replace it, the hissing is actually the vacuum that builds within the booster escaping thru the seal in the booster

Sep 09, 2012 | Oldsmobile Intrigue Cars & Trucks

1 Answer

Brake pedal goes all the way to the floor, will slow the car a little, but wont fully brake. master cylinder is fine, calipers and pads are new, brake lines look okay, it's holding brake fluid fine, lines...


must be something you have overlooked. clamp off the front brake hoses and rear hose. if you dont have the propper clamps use g clamps or locking pliars. try the pedal then. if it still goes to the floor its either air in the lines or the master cylinder is no good..Bleed the master cylinder at the lines first,then work back.

Mar 11, 2011 | Lexus SC 400 Cars & Trucks

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

Just changed rear brake pads on 05 mazda 6. now


This is normal and you need to keep pumping the brakes till they reset there self. Once the brake peddle have reset there self and is firm, check the brake fluid level again and add brake fluid if low. After brakes have reset there self, go for a test drive around the block and check the parking brakes. Good luck.

Nov 17, 2009 | 2004 Mazda 6

1 Answer

2000 isuzu rodeo brake problems


your master cylinder is gone. when stopped apply pedal and hold let up slightly then reapply if pedal sinks to floor master is bad.

Nov 11, 2008 | 2000 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

954 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...