Question about Cars & Trucks

Open Question

Diagram for 1999 infinti Q45 fog lights, need to know how to chang blub

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: How to change fog light bulb

Open the engine hood and you'll see there is a plastic housing holding the head light ans side light to the frame. There are two wing nuts and one wing bolt holding it all together. Remove those and pull the headlight and side light housings out from the frame. You'll be able to access all of the lights now.

Posted on Jul 05, 2009

Ad
  • 34 Answers

SOURCE: On a 1999 Ram 2500... the

Check the fuse located in the secondary fuse panel. It is located on the drivers side of the dash board behind a plastic cover approximately 6" wide by 8" long.

Posted on Jul 08, 2009

ZJLimited
  • 17970 Answers

SOURCE: need a fuse box diagram to wire in fog lights

Fog lamps are installed on the front bumper. The switch is located to the left of the steering column on the dash panel. The fog lamps are turned off by the circuit relay when the high beam driving lamps are turned on. The circuit relay is located on the right front wheelhouse panel near the blower motor.

Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element
See Figure 1
558610d.gif
Fig. 1: Exploded view of a fog lamp assembly

  1. Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
  2. Remove the reflector assembly from the lamp body.
  3. Remove the bulb holder from the assembly. Remove the element from the bulb.

DO NOT handle elements with your bare hands, always handle with a clean cloth. Oil from your hands will cause the element to fail.
  1. Installation is the reverse of removal.

Fog Lamp Switch
The fog lamp switch is removed and installed by simply prying the switch from the instrument panel and unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT

  1. Position the vehicle on a level surface, facing a wall approximately 25 feet away. Remove the lamp stone shields and loosen the adjustment nuts.
  2. Turn the fog lamps ON and adjust as follows:
    1. Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
    2. Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
  3. Install all previously removed items after turning OFF the fog lamps.

1995 Cherokee Chassis Schematic
8e08df0.gif

www.autozone.com

Posted on Aug 11, 2009

  • 10 Answers

SOURCE: How to replace fog light bulb on an '03 Jeep

There is a small square "trap door" in each wheel well directly behind the fog lamps. You can pry it open and access the fog lamps. They just twist loose.

Posted on Feb 11, 2010

  • 1 Answer

SOURCE: Wiring diagram to install OEM 2010 Toyota Camry fog lghts

here is a link that can help you.
http://www.donmar.com/Tech/FogLight-TCA-303.pdf

Posted on Dec 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 Oldsmobile intrigue, the instrument cluster and fog lamps quit working at the same time. At first it was intermittenent, I would disconnect the battery and reconnect it and it would work...


Without testing the electrical circuit's we'd only be guessing . Looking at wiring diagrams to see if the instrument cluster & fog lamps share a common ground or power supply would be a good first step. Do you know how to use a DVOM - digital volt ohmmeter to test electrical circuit's ? Do you know how electrical circuits work ? Electric Testing Techniques You Need to Know
Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. Year , make , model an engine . Under system click on lighting ,then under subsystem click fog lamps . Check power an ground supply . Then under subsystem click instrument cluster ,check where it's power an ground is . Use voltmeter an test the circuit's . Looking at the wiring diagrams i don't see anything these too have in common , power or ground . All you can do is test the circuit's . Find what's missing .

Jan 28, 2018 | 1999 Oldsmobile Intrigue

1 Answer

No power to dimmer fuse


They can not be bypass. That will just create more (Problems) The problem is your head light switch has mess up. There are probaly some wies on it that shorted out.

Oct 22, 2012 | 2000 Saturn L-Series

1 Answer

How do you reset tcs/slip light on a 1999 infinit q45


Hi there:

Pull the codes to get started. Normla process is when the slip light will flash on and then go off. TCS is your Traction Control System. It is normal for it to go off If the rear wheels are slipping. You may have worn tires or you are driving on ice or snow. Are you on a slippery surface when this happens? You can always shut the system down by pressing the TCS off button in the center console.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 17, 2012 | Infiniti Q45 Cars & Trucks

1 Answer

Wiring diagram for spotlights on a discovery I/II (1999) Would like to mount and wire the spotlights up so as they come on highbeam only, and would like to connect it into the ' rear fog light ' switch....


You can find factory wiring diagrams here (free RAVE Download) http://www.landroverresource.com/ And sure you can wire your spots into rear fog switch, depending on watts/draw of your lights you might want to "UP" the fuse rating

Mar 20, 2011 | 1999 Land Rover Discovery

1 Answer

I have an Infinity q45 1999. The


take it to a local mechanic ,he should be able to put the light out for you and advise what the other lights are for

Mar 17, 2010 | 1997 Infiniti.5 Q45

1 Answer

How to replace fog light bulb on an '03 Jeep


There is a small square "trap door" in each wheel well directly behind the fog lamps. You can pry it open and access the fog lamps. They just twist loose.

Feb 11, 2010 | 2003 Jeep Wrangler

1 Answer

I have a jetta fog light are not working fuse is good new blubs any ideas?


there are many problems with the 1995 jetta ignition. All your lights,head lights, fog, and instrument lights get power when you turn the key on. I had to bypass alot of this when i got my jetta. I also reran the wires from the fog and headlights so you can manually turn them on

Jan 30, 2010 | 1995 Volkswagen Jetta

1 Answer

On a 1999 Ram 2500... the "fog" lights won't come on anymore. The headlight switch is pulled to activate these lights. Blubs are good but power is not getting to sockets. How can I test troubleshoot this...


Check the fuse located in the secondary fuse panel. It is located on the drivers side of the dash board behind a plastic cover approximately 6" wide by 8" long.

Jul 07, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15387 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...