Question about 2002 Mitsubishi Eclipse

Open Question

I have a trouble a code p0305 for my 2002 mitsubishi eclipse please describe what this code means!

The readout for troubleshooting is 90305 for my 2002 eclipse. please describe what this code means

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: have trouble code po135 on a mitsubishi eclipse,

Oxygen sensor. try this link & scroll down until you find your codes.

http://www.troublecodes.net/mitsu/

Posted on Jan 31, 2009

  • 1986 Answers

SOURCE: What does trouble code PO 603 mean for a 2007

P0603 Internal Control Module Keep Alive Memory (KAM) Error. This code occurs if you've altered your computer from stock settings

Posted on Sep 09, 2009

bschilz
  • 2049 Answers

SOURCE: Troubleshooting oem code mitsubishi 2005

P0736 means "Reverse incorrect gear ratio". I would take it to a transmission shop for complete diagnosis.

Did you check the fluid level in transmission? If you need to add, don't overfill.
The P0736 code may well mean a clutch problem inside the trans that requires "rebuild". But also with this particular code there is the possibility of it being a faulty turbine speed sensor or output speed sensor. But against that is the fact that the same clutch is used for both low and reverse gears. Actually you are now in 'limp in' mode which uses only 2nd gear as that requires the least parts and is protective against further damage. A fairly simple test can ascertain whether the clutch is indeed bad but that should be done at a shop that has the test tool to measure the input/output sensors. Alternatively, you could buy and replace the turbine sensor (assuming that the output sensor is OK, see below) and if that doesn't change things it pretty much dictates a need for rebuild.

My suspicion is that the low/reverse clutch is out and so will need a rebuild. You might find out the cost of the sensor, but it in yourself and see if that corrects things. Or you might find the labor cost of the differential diagnosis of clutch as compared to sensor failure, and then decide which way to spend the money. If the speedometer seems to be reading accurately that would pretty much dismiss the possibility of the output sensor being faulty

Posted on Jan 06, 2010

Shorty1_wt
  • 324 Answers

SOURCE: I have a 2003 Mitsubishi Eclipse with a P0442 code

http://www.obd-codes.com/p0442
click here for p0442 info

Posted on Jan 28, 2010

  • 54 Answers

SOURCE: My 1997 Mitsubishi Eclipse wont pass emissions

This is the direct definition of this code
Mitsubishi DTC P1390 - Timing Belt Skipped 1 Tooth or More.
Probable Causes,
-Timing belt improperly installed
-Camshaft position sensor improperly installed
-Camshaft position sensor connector improperly connected
-Crankshaft position sensor connector improperly connected
-Camshaft's relative position not relearned after one of the following have been serviced: Camshaft, Camshaft sprocket, timing belt tension-er, cylinder head, head gasket, crankshaft sprocket, crankshaft cylinder block or the PCM.

Sounds like something to do with the timing belt it self. You can go to any Autozone or Checker and ask for a code reader (they will let you use it for free) and it will show this code again. You can also reset the cars computer with the code reader to see if it comes back with the same code.

Posted on Nov 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car dies for no reason after sitting awhile starts up


Try changing crankshaft sensor. You will not get a code readout for this problem. Had same problem on Mercedes ml320 and now works fine

Apr 08, 2013 | 1995 Mitsubishi Eclipse

1 Answer

2002 eclispe 2.4 engine,engine light and battery light are both on installed new altnator and istall new battery


If the check engine light is on you should have the computer checked for trouble codes. That might point you in the right direction to troubleshoot the charging system.
You could have blown the maxi fuse for the alternator.

Oct 01, 2012 | 2002 Mitsubishi Eclipse

1 Answer

What is troulbe code 12 And 55 on 1995 misubishi eclipse


ok code 12 means that you disconect battery recently, maybe you were trying to clear trouble code by doing that, in worst case just replace the battery not a big deal

Code 55 means "no Trouble codes found" code 55 means that thats the end of self testing codes, there is no mode code. just ignore code 55.

im pretty sure you were doing a selft testing dtc bye turning switch on and off.

Nov 08, 2011 | 1995 Mitsubishi Eclipse

1 Answer

Obd code 401


DTC's (trouble codes) are 4 digits long. I am taking it that you mean P0401.Here is a link to a page that explains the code and the possible fixes:

http://www.obd-codes.com/p0401

Sep 18, 2011 | 1999 Mitsubishi Eclipse

1 Answer

My 1997 Mitsubishi Eclipse wont pass emissions because trouble code P1390. I dont know what this means? Ive researched it everyway I know? My check engine light wont come on at all? Help anyone? Thanks!


This is the direct definition of this code
Mitsubishi DTC P1390 - Timing Belt Skipped 1 Tooth or More.
Probable Causes,
-Timing belt improperly installed
-Camshaft position sensor improperly installed
-Camshaft position sensor connector improperly connected
-Crankshaft position sensor connector improperly connected
-Camshaft's relative position not relearned after one of the following have been serviced: Camshaft, Camshaft sprocket, timing belt tension-er, cylinder head, head gasket, crankshaft sprocket, crankshaft cylinder block or the PCM.

Sounds like something to do with the timing belt it self. You can go to any Autozone or Checker and ask for a code reader (they will let you use it for free) and it will show this code again. You can also reset the cars computer with the code reader to see if it comes back with the same code.

Nov 03, 2010 | 1997 Mitsubishi Eclipse

1 Answer

What does trouble code PO 603 mean for a 2007 Mitsubishi Eclipse GT?


P0603 Internal Control Module Keep Alive Memory (KAM) Error. This code occurs if you've altered your computer from stock settings

Sep 09, 2009 | 2007 Mitsubishi Eclipse Spyder GT...

1 Answer

I have a 1999 gs mitsubishi eclipse my check engine light is on the code for the light is p1390 how do i get it fix need help


It appears that there might be a TSB (technical service bulletin) issued on this vehicle by Mitsubishi. Check with your local dealer to verify for certain. One link with brief summary of this on a 1998 model (yours might fall into this class too?) can be seen here and is as follows:

1998 Mitsubishi ECLIPSE 98 - Transmission TCM PCM > POWER TRAIN : AUTOMATIC TRANSMISSION : CONTROL MODULE (TCM, PCM) [Part 103100 ]
TSB No: 01 NHTSA ID: 622435 , May 01, 2001 : Replacement:
Summary: subject regarding diagnostic trouble code p1390 pcm relearn.

A fuller discussion on a 1996 with this code can be seen here. Scroll down to the answer.

Perhaps these will provide a bit of information prior to contacting your dealer. I've never worked in a dealership that charged for looking up & providing info on TSB's. Good luck.

If this helps to solve your problem then please take a moment to rate this post. - Thanks.

Jun 28, 2009 | 1999 Mitsubishi Eclipse

1 Answer

Have trouble code po135 on a mitsubishi eclipse,


Oxygen sensor. try this link & scroll down until you find your codes.

http://www.troublecodes.net/mitsu/

Jan 31, 2009 | 2000 Mitsubishi Eclipse

1 Answer

Pi4oo MSP trouble code mitsu eclipse 1995


The error is actually P1400 Manufacture Controlled Auxillary Emissions Controls. I'm having that issue with my 2001 Mitsubishi Eclipse right now. Not to mention the bad paint job.

Jan 16, 2009 | 1995 Mitsubishi Eclipse

Not finding what you are looking for?
2002 Mitsubishi Eclipse Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...