Question about Ford Fairmont

Open Question

Xh ford cramnksensor location can,t find

Can,t find crank sensor

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

carsandcomps
  • 722 Answers

SOURCE: crank position sensor error 11

Well, being this is v6, take off the fan, and the belt. Since the crankshaft is at the bottom of the engine, the sensor will be located near it at the front of the engine, on one side or the other. It will have a wiring harness connected to it, and should be mounted to a small bracket. It's best to remove the entire bracket, especially if the new unit came with a new one. Use BOTH new parts. Do not adjust timing at all until the sensor has been replaced.

You may need a "feeler gauge" to set this, as they (on some vehicles) need to be spaced at a particular distance from the harmonic balancer (if and external sensor). This I believe is and internal, so you should be fine simply inserting it in place.

Please let me know if you need further assistance.

carsandcomps,

Guru, Premium Expert @ Fixya.com

Posted on May 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of crank position sensor for 1999 ford windstar 3.8 se


Crankshaft position sensor is mounted on the engine front cover next to the crankshaft trigger wheel, below electronic ignition coil pack on transmission housing .

Mar 29, 2014 | 1999 Ford Windstar

1 Answer

Where is the location of crank sensor


Should be near the front crank pulley depending on which engine.

Feb 21, 2013 | 1998 Ford Contour

1 Answer

Ford XH 97A. is there an internal fuse box? i cant find anything under the dash. My wipers have gone kaput but all the other accs are working.


The same thing has happened to my XH - what was the problem? Is it just a fuse? And did you have to take the dash apart to get to the fuse box?

Nov 30, 2012 | Ford Cars & Trucks

1 Answer

Were is the crank sensor located on a 2000 ford tarus


Most crank sensors are located somewhere or near to the crankshaft or sometimes near the camshaft. Trace the wiring harness down to the bottom part of the engine around the harmonic balancer. It should be near it. Hope that helps.

Nov 27, 2012 | 2000 Ford Taurus

1 Answer

Xh fuel pump cuts out


Are you refer at Falcon XH ? Are you check fuses and wires and volateg at/from fuel pump ?

Jun 27, 2012 | Ford Falcon Cars & Trucks

3 Answers

Where is it located ABS Module 2000 Expidition


Where do u unplug abs module on 2000 ford expedition

Dec 15, 2010 | 2000 Ford Expedition

1 Answer

Car is a xh xr6,,on duel fuel...car wont start on either fuels just keeps turning over ..when i turn the car over on gas the lights that indicate how much gas i have starts from red to green then it just...


I have seen similar problems in the past.You should check your ignition system.Mounted by the coil is an igniter on some models.This could be one possibility.Another could be.Also if your crank angle sensor is bad you will get no spark.(mounted inside distributor)If possible can you tell me more about your automobile so Than I can do more research to help find the exact problem.Year make model ect. Thankyou

Oct 17, 2010 | Ford Fairmont Cars & Trucks

2 Answers

2005 ford excursion cam sensor location I need to change the cam sensor and the crank sensors on my excursion and i do not know where they are located


On my 02 Excursion with the 7.3L Diesel, the Cam Position Sensor is located at the front bottom of the engine on the passengers side. There is one electrical pigtail plug that is attached and one bolt holds the sensor in position. It may be located in a similar location on your 05 Ex. I do not know where the crank sensor is located. I hope this helps.

Aug 27, 2009 | 2005 Ford Excursion

2 Answers

Ford falcon 4.0 litre fuel injection, backfires when revved up. please send a diagram of the firing order. Also, the timing is out; owners manual suggest that timing can not be set manually


i have a 96 xh ford falcon 4.0 ute.I am rebuilding the engine and delated the pic i had of the timing set up . I am after a pic or a site that i can see where the timing marks should be. I know that the crank of cause is tdc.(key is on top) cam marker is at 3 o'clock (90 degrees from top). Where does the dizzy gear timing mark point to?

Apr 15, 2009 | 1983 Ford Fairmont

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...