Question about 2004 Mazda 6

1 Answer

2004 mazda 6 wont shift out of 1st gear smoothly. It whines, then finally catches. If it's cylinder (will be 3rd one) which number is it?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Your gear selector linkage cable has come adrift from the linkage bracket just below the battery tray ,you can temporarily fix with two cable ties ,but will need to replace one of the two cables one is for neutral and the other is to select gear

Posted on Jan 17, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 14 Answers

SOURCE: 2000 mazda 626 wont shift into gear at all!

Sounds Like You Broke an Axle, And Possibley Broke Something At The Transmission. Good Luck

Posted on May 03, 2009

  • 1 Answer

SOURCE: 2004 mazda mvp firing order

The firing order is 1-4-2-5-3-6. The cylinders are, front bank is from drivers side to passenger, 6-5-4 , and 3-2-1 at the firewall. This is for a 2004 Mazda MPV.

Posted on Dec 03, 2008

alicantecoli
  • 22246 Answers

SOURCE: hard shift from 1st to 2nd gear automatic

what year is vehicle please ?? as people often put it in wrong catagory ,if its mazada 2007 then its dealer only as a computer controls it all and the software is factory encrypted to stop general garages from repairing it .But check for a vacumn pipe loose under bonnet ,thin rubber pìpe from inlet manifold to gearbor or a diaphram switch,

Posted on Feb 19, 2009

ourhowse
  • 2007 Answers

SOURCE: 2004 mazda 3 transmission problem

Check transmission fluid. If that is full, try changing the fuel filter. It could be starving for gas, and trying to shift but can't. It could also be the speed sensor, or shift solenoid.

Posted on Jul 06, 2009

  • 13 Answers

SOURCE: mazda rx8 2004 wont shift into gear

Remove shift knob, remove ash tray, remove plastic over with shift boot, look for reset button.

Posted on May 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

VERY Bizarre Combination of "Symptoms" I Believe Relating to Clutch or Transmission, or heaven forbid worse! Please help!


Hi,

First, congrats on the most detailed problem description I have ever seen! Seriously, it does assist us.

All this is completely consistent with your clutch not releasing properly, meaning that the gearbox is still turning when the pedal is depressed. The syncros in the gearbox will then keep you out of gear, that is what they should do. You can indeed shift into higher gears however when driving as the gearbox revs more nearly match to what is needed. The jerking forward when you hit the starter is due to the poor old starter motor having to move the whole car instead of just the engine, because the clutch has not released !

Now as to why, it is likely that the clutch release fork has broken, inside the housing. I had this once with a Mazda, and symptoms were exactly as you describe. The gearbox has to be removed if this is the problem, and you should also then take the chance to renew the clutch, pressure and driven plate both, unless quite new.

Also a possible cause is a complete loss of clutch fluid if a hydraulic clutch, or a broken cable if that type of clutch. Loss of fluid in a hydraulic clutch can be easily checked in the fluid reservoir, and can occur if a hose splits
..

Jun 19, 2016 | 1995 Mazda Protege

3 Answers

I have a 2004 Envoy slt 4wd auto....The car will shift fine from 1st to 2nd gear but rpms climb and it does't go to 3rd. I tried to maunually shift through gears, but it still doesn't get 3rd?


its most def a purely transmission issue i believe its the solenoids. have it taken to a reputable trans shop near and have them diagnose it with there speciall code reader.

Oct 24, 2012 | 2004 GMC Envoy SLT

1 Answer

I have a 2004 mazda 6 the car jumps from 1st gear to 3rd and the battery light comes on what can it be


If the battery light is on you alternator is not charging.
Check that first , as for the trany , when voltage drops below minimum requirement , computers may act up wierd.

Jun 30, 2010 | 2004 Mazda 6

2 Answers

2004 Mazda 6, battery light is on.


what has this got to do with the battery light coming on

May 11, 2009 | 2004 Mazda 6

1 Answer

Transmission wont shift until about 4000rpms from 1st to 2nd gea


Have a code check done and see if speed sensor or controller is working properly. if bought from a dealer, get it back there asap...they can't sell it in that condition!!...No test drive before you ploped down your money?

Apr 16, 2009 | 2004 Jeep Grand Cherokee

1 Answer

My 92 honda accord will not go into 1st 3rd or 5th gear


check shift fork adjustment. make sure you bleed the slave cylinder.also check shift cable adjustment.

Apr 11, 2009 | 1992 Honda Accord

1 Answer

Chunky Shitft in automatic transmission


try changing the transmission fluid.

Mar 18, 2009 | 2005 Mazda 6

1 Answer

When going throught the gears forward sometimes it takes more muscle to change particularly 3 to 4 or 4 to 5 ..... sometimes it is easy to change gear and sometimes it seems to take more effort ....kind of...


try double clutching(come out of 3rd then push clutch twice b-4 going to 4th. if this works your clutch slave may be weak or pressure plate is worn. Try shifting from 1st-3rd if engine revs like your in neutral replace clutch. when going 1st-3rd engine should catch and cause vehicle to buck&stumble. (check level of clutch master cylinder)

Nov 26, 2008 | Toyota Paseo Cars & Trucks

Not finding what you are looking for?
2004 Mazda 6 Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...