Question about Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: flasher/2002 saturn l300
youturn signal flasher is part of the hazzard switch located in the center of the dash above the radio. the trim piece around the radio and the climate controls pops off using a small flat bladed scewdriver.
Posted on Mar 31, 2009
Sounds like a water pump or radiator hose. Need to see exactly where the leak is coming from to confirm which.
Posted on May 31, 2009
SOURCE: high side schrader valve leaking
if it has a ball looking scharder u may can replace the whole service port,if it is made on the line u have to replace the whole line ,,,,if it looks like a regular every dat scharder u can buy a new one and a tool to replace it ,if ur very fast u can do it and not lose much freon but otherwise drain system and evacuate and recharge
Posted on Jun 28, 2009
First, no coolant flows through the intake on the 3.0L in the L300 and Catera. The intake is a 5 piece setup, the base of which is a phenolic spacer to isolate heat from the intake manifold.
Beneath the phenolic spacer there is an oil cooler installed between the cylinders inside the block. There is a cover with 2 oil cooler lines that run up from the right side of the engine to the cover and into the cooler via an inlet and outlet banjo bolt. If the cooler wears out there will be an exchange of coolant and oil, more oil into the coolant than coolant into the oil, although there will be some.
You might notice a small drop in performance, and later will notice that the coolant reservoir is full of oil and is spilling over.
I'd start by checking cylinder compression to make sure you don't ALSO have a blown head gasket, but the cooler is quite notorious for blowing out. If you do decide to replace it you will need:
1: a new oil cooler
2: new gaskets for the steel cooler lines, they will be metal crush gaskets. 4 as they are for the banjo bolts (2 washers for each bolt, one bolt on each line)
3: 4 new gaskets for the coolant bridge (the almost crescent shape aluminum bridge next to the oil cooler cover, aluminum with hoses attached as well as the coolant temp sensor)
4: New gaskets for the banjo bolts on the coolant bridge, they're rubber but don't just use some junk! Get the real deal ones from the dealer and save yourself the trouble of redoing it later on. They're cheap.
5: Oil, Antifreeze and a new oil filter. I'd spring for the Coolant system cleaner if it's not a big deal, less oil in the cooling system makes for a better performing engine and better heat in the winter.
Tools: 3/8" ratchet, standard set of extensions for the ratchet, set of Torx sockets and inverted Torx sockets, set of 3/8" sockets, flat head screwdriver, dikes or side cutters.
1: take off the intake manifold clamps by prying where they latch together, don't damage them unless you plan on replacing them (your call, but a tech would reuse them)
2: take off all the Torx bolts for the manifolds, there's 4 pieces to the aluminum manifolds and the ECM and Vacuum reservoir have to come off the rear manifold to get to some of the bolts. NOTE the location of all vacuum lines and coolant lines so you don't forget them later. Also note the position of the ECM on the manifold so you don't have to figure out which way it goes on later, it only plugs in one way but it's a pain if you fumble it up.
3: Take out the phenolic spacer (black thing under all the manifolds, feels like plastic). There are rubber gaskets on these, if they're damaged then it's a good time to replace them, if not they are usually reusable. Napa, Advance Auto, Auto Zone, etc. always have them. Just ask for intake manifold gaskets, even though they're really phenolic spacer gaskets.
4: Remove the banjo bolts for the oil cooler lines, note the placement of gaskets on each side of the line that the banjo bolt goes through. You'll want to remember that later to avoid a leak. Also remove the coolant bridge banjo bolts and move it out of the way, again noting the gaskets for later replacement.
5: loosen the 2 nuts where the oil cooler lines were, these are attached to the oil cooler and secure it to the cover.
6: Remove the Torx bolts for the cooler cover, lift the cover, and remove the cooler. Make sure you clean that galley out real well, saves you some headache when cleaning later on.
7: When reinstalling the oil cooler cover remember to use a 2mm bead of sealant around there. I've seen guys use Permatex Orange, but if you can swing it then get something better from the dealership. You don't want to do this again in a year if the Permatex leaks on you.
8: Reinstall coolant bridge, oil cooler lines, phenolic spacer, manifold(s) and clamps. Double check all your work! Change your oil, and flush out the cooling system.
Estimated time? For a tech.. probably 2 hours. For a Shadetree mechanic? Probably 4 to 5 hours.
Posted on Oct 08, 2009
Tips for a great answer:
Feb 09, 2016 | 2002 Saturn L-Series
Mar 19, 2015 | 2004 Saturn L300
Feb 27, 2013 | 2006 Saturn L300
Oct 08, 2012 | Saturn L300 Cars & Trucks
Oct 29, 2011 | 2002 Saturn L-Series
Oct 01, 2010 | 2006 Saturn L300
Jul 29, 2010 | 2002 Saturn L-Series
Mar 22, 2010 | 2006 Saturn L300
May 31, 2009 | 2001 Saturn L-Series
67 people viewed this question
Usually answered in minutes!