Question about Cars & Trucks

1 Answer

Clutch master cylinder gone do i also have to change slave cylinder due to bleeding problems 1999 Grand voyager

Ive been told that a clutch master cylinder is no good without changing the slave cylinder as well as i will expirence bleeding problems unless ichange the both on my 1999 chrysler grand voyager

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Spread the Word:

    An expert who has shared 5 answers on their Facebook wall.

  • Expert
  • 120 Answers

No need to change the slave cylinder, but bleed both and if you have low or no brakes then bleed the brakes too.

Posted on Jan 08, 2013

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1999 Dodge Ram 3500 Pickup - Clutch

use a hand vacumn and cover over the reservoir, apply light vacumn and the air will come to the reservoir, usually take 2 or 3 time and the air will work back out to the top,

Posted on Apr 16, 2009

  • 1 Answer

SOURCE: Hydraulic clutch problems

i have a ktm 125 wich all ktms have hydraulic cluthcs and i have the same problem as all these fellas even when im riding it just sucks right down all the fluid reply to me on X-KTMrida-X@hotmail.com ok thanks fellas

Posted on Oct 27, 2008

  • 2187 Answers

SOURCE: Bleeding Clutch Cylinder with no bleeder screw

I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Posted on Jun 04, 2009

  • 1 Answer

SOURCE: 1999 pontiac sunfire bleeding clutch

my 1999 pontiac sunfire drivers door latch is broke can not close the door. i have it pulled shut? how much will a used latch cost, or even 3 bolts for it? all the auto stores/ jumk yards are closed for me to call

Posted on Aug 01, 2009

  • 70 Answers

SOURCE: no clutch pedal been bleeding it for 3 days

these are notorius for clutch bleeding problems, there is no good answer other than to keep pumping that pedal, eventually it will bleed out

Posted on Dec 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mx 6 clutch bleeding


I've had this happen to me once, as did a friend of mine.
Both times the clutch SLAVE (not master) cylinder needed to be replaced, THEN the system bled.
The MASTER cylinder is the one on the firewall, that's connected to the clutch pedal arm.
The SLAVE cylinder is bolted to the bellhousing (between the engine and the transmission).
BUT, it COULD me the master cylinder also.
Whichever is bad, there should be some fluid leaking to give it away.

Jan 14, 2014 | Cars & Trucks

2 Answers

My clutch seems to have gone out tonight. The clutch is very easy to push to the floor...and it pops back....there's no pressure at all. The clutch fluid is leaking from the hose. Could this be the...


it could be either the master cylinder or the slave cylinder,it could also be the clutch pressure plate check the master & slave cylinders first because if it's the pressure plate the gear box will have to be removed to replace the pressure plate, even if you are uncertain it is most likely cheaper to replace the master & slave cylinders than it would be to replace the pressure plate.....hope this helps......cheers.

Aug 31, 2011 | Saturn Vue Cars & Trucks

1 Answer

New clutch master cylinder new slave cylinder new release fork and bearing new clutch, have bled three bottles through the system and still not enough movement at the slave cylinder to release clutch


Hi,
You need to check that you are actually getting the full length of stroke from the master cylinder.
If you are then you still a captive air pocket in the master cylinder and the only way to get rid of it is to vacum bleed the system from the master cylinder to the slave cylinder.
Check these and let me know, I can give you further information.
Thanks
Jason

Aug 22, 2011 | 1999 Suzuki Grand Vitara

1 Answer

Hi there i have a 98 vw golf which i have changed the clutch master cylinder and the slave cylinder ive pumped the oil back into the system from the nipple on the slave cylinder until the oil came up into...


I would start by draining the oil out and replacing it with brake fluid added into the reservoir and drained down and out the nipple. then i would bleed the system, going to need a helper for this procedure, look on youtube to see someone bleeding a hydraulic clutch.

Dec 28, 2010 | 1998 Volkswagen Golf

2 Answers

The problem is the clutch stays of the floor. I have been told to change the master and slave and I've been told to bleed it. What do you recomend?


could be the clutch, release bearing , slave cyl, master cyl, air in the system or a leaking line , before you go replacing or fixing firn out what is gone bad, hope this helps

Nov 19, 2010 | Toyota Pickup Cars & Trucks

1 Answer

Are the brake master cylinder and the clutch slave cylinder interconnect in some way? I'm told that the slave cylinder get its fluid from the master cylinder.


The brake system and the clutch master cylinder have the same fluid tank, look at the brake master cylinder fluid tank, on the right hand side about half way up is a hose that goes over to the clutch master cylinder, if fluid level is not above this hose the clutch will stop functioning. If the clutch slave cylinder, mounted on the front side of transmission bellhousing, leaks then the clutch will stop functioning. The slave cylinder has a bleed screw, check these items and fill and bleed as neccessary. Hope this helps, let me know.

Jul 28, 2010 | 1995 Ford Escort

1 Answer

Changed clutch but unable to bleed the slave cylinder. Does that mean clutch master cylinder is bad? Got one from parts store but can't figure out how to take the clutch safty switch off to change it. Any...


Probably not. Bleeding clutch slave cylinders is tricky because you cant "pump it up". The master cylinder has no static valve so the best way to bleed the slave cyl. is to use gravity. Fill the master cylinder reservoir and open the bleed valve on the slave cyl. Allow fluid to drip into an open can until there's no trace of air. Close bleed valve and try clutch. If still no pedal, repeat the process. This is quite an acceptable procedure.

Mar 22, 2010 | 1991 Chevrolet S-10

3 Answers

2001 Ford ranger edge. The gears won't change.


The trans will need to come out. While your at it, just replace the clutch assembly, rear main oil seal, resurface the flywheel, and the clutch master cyl. Its not really a job you should do, find a repair shop to handle it.

Nov 06, 2009 | Ford Edge Cars & Trucks

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

1 Answer

Clutch cylinder inside car is it broke


you have to bleed the air out of it. If there is not fluid leaking from the master cylinder on the firewall.it can leak on the inside of car or the out side if the master cylinder is bad.first make sure the reservoir stays full then open the bleeder on slave cylinder. this is called gravity bleeding. once fluid comes out, tighten bleeder, pump pedal one time loosen bleeder while holding clutch pedal down and then tighten. do this repeatedly until no air comes out. you can pump pedal several times,then hold and bleed however you like but I have better luck with individual pumps. just make sure that the lines hooked to slave cylinder are tight and there are no air leaks. and that the line does not go below the slave cylinder because sometimes air gets trapped in the lowest part of system.

Jan 12, 2009 | 1996 BMW 318

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...