Question about 2000 Nissan Pathfinder

Open Question

How to replace needle bearing in front wheel - 2000 Nissan Pathfinder

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 24 Answers

SOURCE: replace front wheel bearings

The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Posted on Jun 20, 2008

c17hydro
  • 2984 Answers

SOURCE: Directions replace front wheel bearings on a 1985 nissan stanza?

996fb79.gif

NOTE: After the wheel bearings have been removed or replaced or the front axle has been reassembled be sure to adjust wheel bearing preload. Refer to the Adjustment service procedure below. On the 1989–92 240SX there is just one wheel bearing, pressed into the hub and no adjusting cap. Refer to the exploded views of the Front Axle Hub Assembly. Review the complete service procedure.

  1. Raise and support the vehicle safely.
  2. Remove the front wheels and the brake caliper assemblies. NOTE: Brake hoses do not need to be disconnected from the brake caliper assemblies. Make sure the brake hoses are secure and do not let caliper assemblies hang unsupported from the vehicle.
  3. Work off center hub cap by using thin tool. If necessary tap around it with a soft hammer while removing.
  4. Pry off cotter pin and take out adjusting cap and wheel bearing lock nut.
  5. Remove wheel hub with disc brake rotor from spindle with bearings installed. Remove the outer bearing from the hub.
  6. Remove inner bearing and grease seal from hub using long brass drift pin or equivalent.
  7. If it is necessary to replace the bearing outer races, drive them out of the hub with a brass drift pin and mallet.
  8. Install the outer bearing race with a tool (KV401021S0 special tool number) until it seats in the hub flush. NOTE: Place a large glob of grease into the palm of one hand and push the bearing through it with a sliding motion. The grease must be forced through the side of the bearing and in between each roller. Continue until the grease begins to ooze out the other side through the gaps between the rollers. The bearing must be completely packed with grease.
  9. Pack each wheel bearing with high temperature wheel bearing grease. Pack hub and hub cap with the recommended wheel bearing grease up to shaded portions. Refer to the illustration.
  10. Install the inner bearing and grease seal in the proper position in the hub.
  11. Install the wheel hub with disc brake rotor to the spindle.
  12. Install the outer wheel bearing, lock washer, wheel bearing lock nut, adjusting cap, cotter pin (always use a new cotter pin and O-ring for installation after adjustment), spread cotter pin then install the O-ring and dust cap.
  13. Install the brake caliper assemblies and bleed brakes if necessary. Install the front wheels.

Posted on Jun 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you repack front wheel bearings on a 98 Cherokee 4X4


OP<
Posted by J Sparacino on Aug 31, 2016
you double posted. why do that????
no, the hubs are integrated bearing hubs.
here read the parts pages,
see any tapered bearings there,
if not sold , pray tell , how can you pack the bearing not in hand.
not only that, there are like 1000000 books on how to pack front bearing, if they were removable and are not.
why not look first then post.? at car and the book, !
or read the FREE FSM, it says what ?, unbolt them
and replace the integrated hub assembly.
that is a fact. 300 times ive posted the free book, now.
and is still there, and the words still real ,still jeep words and all accurate. sigh.
below is rockautos list of after market hub assemblies.
do not get confused at those needle bearings, those are actually front axle shaft bearings, not hub wheel bearings. fact.
wheel bearing are ball or tapered rollers, to handle lateral huge loading.

http://www.rockauto.com/en/catalog/jeep,1998,cherokee,4.0l+l6,1315943,brake/wheel+hub,wheel+bearing+&+hub+assembly,1636?a=Referer+duckduckgo.com+URL+%2F

56a4ac86-d271-4704-9005-ab6d4f0bc76f.jpg

Aug 31, 2016 | 1998 Jeep Cherokee 4WD

1 Answer

Is it possible to remove and replace front wheel bearings with out a press


In order to remove the front wheel bearings without press hub off the bearing and then the bearing out of the knuckle. To do the first step need a a Support Bridge.It is a special tool. Make bridge and use a general bearing pulled kit to replace bearings. use a "Front Wheel Drive Bearing Removal Adapters Puller Pulley Tool Set Kit" .To replace the bearing, remove front CV shaft taking care not to move the CV shaft too far out .

Nov 06, 2015 | 2002 Kia Rio

1 Answer

How do I replace a front wheel bearing?


front wheel bearing is pressed into hub and has retaining clip on rear and then cv axle shaft comes through center and has a nut and keeper pin. Rule of thumb is to replace both front wheel bearings at same time. raise front of vehicle place on jackstands for safety remove front wheels remove brake calipers remove front rotors and cv axles remove steering hub assy from lower ball joint,tie rod end and struts take hub to shop and have bearing pressed out have new bearings pressed in reassemble front wheels in reverse order of disassembly.

Aug 03, 2014 | 2002 Mitsubishi Lancer

1 Answer

Front wheel assembly diagram


For front wheel assembly diagram and replacement,click the link below and go through procedure:----Front wheel hub assembly Diagram and replacing procedure? http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html
----------Front wheel assembly diagram to replace wheel bearing? http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html
-------------How to replace Front wheel bearing? http://howtobyme.blogspot.in/2012/02/how-to-replace-front-wheel-bearing.html
-----------Check all 3 links one by one.This will help.Thanks.

Feb 22, 2012 | Ford F-250 Cars & Trucks

1 Answer

Front right hub and sensor assembly or a diagram


stevenhurc_11.jpg

Removal Steps

1. Torsion bar

2. Wheel speed sensor

(if equipped with ABS)

3. Back plate

4. Lower ball joint

5. Upper ball joint

6. Knuckle assembly

7. Oil seal

8. Thrust washer

9. Needle bearing

10. Knuckle

Installation Steps

10. Knuckle

9. Needle bearing

8. Thrust washer

7. Oil seal

6. Knuckle assembly

5. Upper ball joint

4. Lower ball joint

3. Back plate

2. Wheel speed sensor

(if equipped with ABS)

1. Torsion bar

Mar 01, 2011 | 1999 Isuzu Trooper

1 Answer

How do you remove the Hub and Rotor on a 97' F250 with Auto 4 wheel drive? I can not get the rotor to come off. I know that the hub must come with it. However, I am not sure what I have not removed in...


Section 05-03C: Wheel Hubs and Bearings, Front Wheels, 4-Wheel Drive 1997 F-250/350/Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000 Locking Hubs, Manual

e9801b.gif


Item Part Number Description 1 3A329 Halfshaft 2 3C132 Rolling Diaphragm Seal (Axle) 3 3299 Integral Spacer Needle Bearing Seal 4 3123 Bearing, Caged Needle 5 3105 Front Wheel Spindle 6 1190 Wheel Hub Grease Seal 7 4221 Inner Wheel Bearing (with Bearing Cup 4222) 8 1102 Front Disc Brake Hub and Rotor 9 4221 Outer Wheel Bearing (with Bearing Cup 4222) 10 - Pin (Part of 1195) 11 1195 Inner Lock Nut 12 1198 Lockwasher 13 1197 Outer Lock Nut 14 - Steel Thrust Washer
(Part of 3B458) 15 - Plastic Thrust Washer
(Part of 3B458) 16 - Splined Thrust Washer
(Part of 3B458) 17 3B457 Snap Ring 18 1K105 Hub Body 19 - Lock Ring (Part of 1K106) 20 1K104 Cap 21 1K104 Capscrew A - While Rotating Front Disc Brake Hub and Rotor, Tighten Inner Lock Nut to 68 Nm (50 Lb-Ft) to Seat Bearings. Back Nut Off 90 Degrees (1/4 Turn). B - Tighten to 217-278 Nm (160-205 Lb-Ft) C - Tighten to 4-6 Nm
(35-53 Lb-In) Removal
  1. Separate cap assembly from hub body by removing the three Torx® head capscrews.


    de0460a.gif



    de0285a.gif

  1. Remove the lock ring seated in the groove of the front disc brake hub and rotor (1102).


    f4658c.gif

  1. Remove the hub body assembly from the front disc brake hub and rotor. If the body is difficult to remove, install two capscrews and pull the body assembly out of the front disc brake hub and rotor.


    f4659d.gif

Installation
  1. NOTE: Do not pack the hublock body assembly or cap with grease. Excessive grease can cause excessive dialing effort and hub failure.

    Follow removal procedure in reverse order.
  1. Tighten three Torx® head capscrews to 4-6 Nm (35-53 lb-in).

Oct 04, 2010 | 1997 Ford F250 SuperCab

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

Not finding what you are looking for?
2000 Nissan Pathfinder Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...