Question about 2000 Chrysler Sebring

1 Answer

2000 chrysler sebring conv

I have a 2000 chrysler sebring conv 2.5L and I have replaced the throttle position sensor because that was the code I got when checked with machine and car is still not running right and this code is still showing up the shop I have taken it to says they also get the same code when checked with their machine and they also seem to think the time belt has jumped and I had that replaced also about 6 mos ago. The car will not stay running unless you keep your feet on the gas and let the motor get warm and then it will run at idle could the timing cause this problem or could it be something else, I have had several people look at this and they seem puzzled any suggestions.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chrysler Master
  • 331 Answers

This is the diagnostic procedure for your problem. (this is actually from a 3.0L engine but the procedure is exactly the same for the 2.5L)

click for full size
2000 chrysler sebring conv - 3f6ba68.jpg
2627050.jpg



Posted on Jan 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sensor P0340 where does it go on 2005 chrysler sebring


Trouble Code: P0340

No Camshaft Position Sensor Circuit Failure

Possible Causes:


CMP Sensor connector is damaged, open or it is shortedCMP Sensor signal circuit is open or shorted to ground or to battery voltage or 5v supply circuitCMP Sensor 5v supply circuit is open or shorted to ground or to battery voltageCMP Sensor ground circuit is openCMP Sensor is damaged or has failedCKP Sensor is damaged or has failedPCM has failed.Here's a link to your sensor.

Mar 16, 2013 | 2005 Chrysler Sebring Conv

1 Answer

2005 crysler sebring 4 cyl no start p 0340 code changed camshaft position sensor still no start. key engaged engin turn over, fuel present, no start, occasionally get a small backfire. HELP!!!


Try substatutting the ignition module with a known goog one.Also have the camshaft CIRCUIT checked at the camshsft sensor plug in, for propper voltage.The code P0340 indicates a circuit malfunction not a sensor malfunction. Good luck.

Dec 07, 2010 | 2005 Chrysler Sebring Conv

1 Answer

Where is the camshaft position sensor located on my 2001 chrysler sebring convertible?


camshaft position sensor is at the back end of the camshaft. should be just across from the battery.

Nov 28, 2010 | 2005 Chrysler Sebring Conv

1 Answer

Car shuts off while driving now won't start check engine light came on while driving


check code probable p0340 camshaft position sensor. I have the same problem on 2005 sebring sedan. I was told to check the circuit at the crankshaft and camshaft sensors for the proper voltage. I'm still trying to figure mine out. If you find your answer, let me know.

Nov 21, 2010 | 2005 Chrysler Sebring Conv

1 Answer

I have an '04 Chrysler Sebring Conv. 6 cyl with an error code of P 1296. What does that error code mean ?


CODE P1296 - 5 VOLT VREF SUPPLY NOT PRESENT - POSSIBLE CAUSE MAP SENSOR VREF CIRCUIT OPEN BETWEEN THE SENSOR AND PCM / MAP SENSOR GROUND CIRCUIT OPEN BETWEEN THE SENSOR AND PCM / MAP SENSOR IS DAMAGED OR HAS FAILED / PCM HAS FAILED.

Nov 09, 2010 | 2004 Chrysler Sebring

1 Answer

2005 Chrysler Sebring - engine stumbles and won't excel. and has the engine codes P0016, P0300, P0339


I wasn't able to find out the first engine code, but the other one is a multiple or random misfire. and crankshaft position sensor a circuit. If the car has a distributor you could tried replacing the cap rotor and also wires first. Next you would look at the crankshaft position sensor try unplugging and plugging it back in. Look at the connection and wires to make sure they look OK. If you do not know how to test this you could also just replace the sensor. Good luck.

Jun 25, 2010 | 2005 Chrysler Sebring Conv

1 Answer

Where is the crankshaft position sensor located on a 2000 Sebring Conv.


removal steps (CPS) -remove air intake hose -Battery tray -Crankshaft position sensor

Apr 27, 2010 | 2000 Chrysler Sebring

2 Answers

I have a 2000 Chrysler Sebring that wont idle. The car starts and will run only if I step on the gas pedal.


clean the IAC. Use spray carb cleaner and spray the idle air control valve. It is on the throttle body near the throttle plate. It may have become stuck with deposits.

Clean the throttle body as well. Check for vacuum leaks

Feb 05, 2009 | 2000 Chrysler Sebring

1 Answer

Throttle position sensor


its located on the opposite side of the throttle body as the throttle cable. remove the whole throttle body then remove the TPS from it.

Jan 15, 2009 | 2000 Chrysler Sebring

Not finding what you are looking for?
2000 Chrysler Sebring Logo

Related Topics:

426 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...