Question about 1993 Mercury Tracer

1 Answer

1993 mercury tracer horn wont stop- how do i disconnect it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There are 2, flat metal connectors leading into the horn. Disconnect one or both. This will stop the horn, FOREVER !!!!!!!

Posted on Jan 08, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Mike258
  • 1498 Answers

SOURCE: serpentine belt for 1998 mercury tracer

Hey there MSM,

  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • Get the belt around all the pulleys except the A/C compressor or Alternator. The routing diagram is on one of the radiator supports.
  • The tensioner pulley is near the Alternator toward the center of the engine. It's on a spring loaded arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done
Mike

Posted on Dec 14, 2008

dgjtex
  • 405 Answers

SOURCE: 1993 Mercury Tracer blower motor location

Right hand side under dash behind glove box

Posted on Dec 27, 2008

  • 4 Answers

SOURCE: 1993 mercury tracer

To replace the headlight on a 1993 Tracer you must turn the black plastic retainer ring counter clockwise and then pull back gently. The ring and bulb should then slide out toward the engine.
Carefully grab the sides of the plug and pull the bulb out.
When replacing the bulb make sure not to touch the glass part or it will cause the bulb to burn out sooner. Place the black ring back over the bulb with the open end towards the glass part of the bulb. Fit the wiring onto the back of the bulb and insert the bulb back into the reflector. The black plastic ring has notches that fit over protrusions. Turn the black ring clockwise and your done. Test the headlight. Happy Driving

Posted on Jan 28, 2009

  • 1 Answer

SOURCE: Does a broken timing belt permanently damage a Mercury Tracer

depends on the Engine in the car.

1.9L SOHC (SEFI on Valve Cover)engine, no, they are non-interferance engines, put a new timing belt on it and go.

1.8 DOHC engine, yes, it will destroy the valves, head, pistons, and if really bad, the block too. These engines are interferance engines, where the valves just barely miss the piston as it comes up, and when the belt breaks it will hit the valves and destroy the engine.

Posted on Mar 06, 2009

emissionwiz
  • 75066 Answers

SOURCE: were is the horn on a mercury tracer 1998

the horn is not the problem here, this is

In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to disarm the airbag system can result in an unexpected Airbag deployment and possible serious personnel injury disconnect the battery 30 minutes prior to start of work.

Posted on Apr 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Firing order for a 1993 mercury tracer


Hi Ronald,the 93 Tracer has 2 engines listed for it,the 1.8 and the 1.9.Here's the link to the 1.8 engine. Specifications Firing Order AutoZone com Here's the link to the 1.9 engine. Specifications Firing Order AutoZone com

Mar 07, 2017 | 1993 Mercury Tracer

1 Answer

Wont start but will turn over


Check wiring, you have accidently knocked something loose. the engine should run even without a water pump.

Nov 07, 2013 | 1993 Mercury Tracer

1 Answer

My sisters 1997 mercury tracer will not shut off, what would cause that? she said that she went to honk the horn and it would not stop and then it shutoff and no longer worked. We replaced the relay and...


This was not a horn problem neither was it the relay but the contacts within the steering wheel that got stuck, u need to have this opened and poped back into position such that when not depressed there wont be any contact.

Jun 12, 2011 | 1998 Mercury Tracer

1 Answer

Why does my 1993 mercury tracer slips in and out of overdrive gear on the open highway?


Have you had the transmission serviced lately? Sounds like the transmission fluid is getting too hot and shifting it out of OD. Check to make certain the fluid is clean, the filter is not stopped up, and the transmission cooler is also not stopped up. Good Luck

Dec 27, 2010 | 1993 Mercury Tracer

1 Answer

My starter will not stop running on my 1993 tracer


You have the starter contacters with a worn groove. the plunger is wedging in and sticking. The starter needs to be rebuilt.

May 23, 2010 | 1997 Mercury Tracer

1 Answer

Were is the horn on a mercury tracer 1998


the horn is not the problem here, this is

In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to disarm the airbag system can result in an unexpected Airbag deployment and possible serious personnel injury disconnect the battery 30 minutes prior to start of work.

Apr 03, 2010 | 1998 Mercury Tracer

1 Answer

Need to change out dash light bulb on a 1993


you will have to remove the dash panel around the cluster to get the cluster out. should be held in place with a couple of philips screws and some 7mm or 1/4in bolts remove these and the panel should pop loose will have to disconnect the switchs mounted in the panel. the speedo cluster is next and is bolted in place. you will probably have to work around the steering wheel and column. make sure to unplug speedo and if shift indicator on dash careful not to break it.

Aug 26, 2009 | 1993 Mercury Tracer

1 Answer

Fuse Diagram


d34dbde.png
This should help you.

Oct 09, 2008 | 1993 Mercury Tracer

1 Answer

1993 mercury tracer


To replace the headlight on a 1993 Tracer you must turn the black plastic retainer ring counter clockwise and then pull back gently. The ring and bulb should then slide out toward the engine.
Carefully grab the sides of the plug and pull the bulb out.
When replacing the bulb make sure not to touch the glass part or it will cause the bulb to burn out sooner. Place the black ring back over the bulb with the open end towards the glass part of the bulb. Fit the wiring onto the back of the bulb and insert the bulb back into the reflector. The black plastic ring has notches that fit over protrusions. Turn the black ring clockwise and your done. Test the headlight. Happy Driving

Oct 08, 2008 | 1993 Mercury Tracer

Not finding what you are looking for?
1993 Mercury Tracer Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...