Question about 1995 Jeep Grand Cherokee

2 Answers

1999 jeep grand cherokee laredo keyless remote transmitter programing

Posted by on

  • monchalet Jan 28, 2009

    I would also know how to program a used keyless remote for my truck that I have bought recently.

  • lenae17 Feb 21, 2009

    I have a 99 jeep my driver windows will go down with the control on the driver side but my passenger windows want go down with either driver trying to operate and with the passenger operating them also my remote stop working when all this did.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

Open the drivers door and turn the key to the on position. Lock the doors with the switch on the door. After the doors lock point the transmitter to the little bulb on the ceiling. Press the LOCK button and hold it until the doors unlock.

Maybe this info can be help you...
http://autorepair.about.com/library/faqs/bl868f.htm

Posted on Feb 06, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Http://www.thejeep.com/pilandprogram.html

Posted on Feb 09, 2009

1 Suggested Answer

  • 4 Answers

SOURCE: keyless remote transmitter programming

You will have to have a Jeep/Chrysler/Dodge service tech hook up their programed OBD2 scanner to reset.

Posted on Jan 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Keyless remote 1996 jeep grand cherokee laredo programing


Instructions
  1. Programming the First Transmitter
    • 1

      Unlock all of the Jeepicon1.png Grand Cherokee's doors and open the driver's side door. Keeping the door open, lock it using the manual lock on the door itself.

    • 2

      Put the manual key into the ignition and switch it to the "On" or "Run" position, whichever applicable, without starting the engine.

    • Sponsored Links

    • 3

      Point the remote at the receiver (located by the little bulb on the caricon1.png ceiling) and hold down the "Lock" button for up to 5 seconds.

    • 4

      When the driver's side door unlocks, you know the remote has been programmed correctly. If you are only programming one remote, jump to the next step. If not, manually re-lock the driver's side door and repeat steps 5 and 6 using each remote you would like to program and then continue.

    • 5

      Turn the key to the "Off" position and turn the ignition on immediately. This must be done within 20 seconds of programming the last remote. You're finished!

Sponsored Links

Read more: How to Program the Remote on a 1996 Jeep Grand Cherokee ' eHow.com http://www.ehow.com/how_7433787_program-1996-jeep-grand-cherokee.html#ixzz2KdCc5PQq

Feb 11, 2013 | 1996 Jeep Grand Cherokee

Tip

Do it Yourself: Reprogramming the Remote Keyless Entry (RKE)


Normal 0 21 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tabla normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Jeep Grand Cherokee Alarm System (1993-1998)

I would try reprogramming the Remote Keyless Entry (RKE) transmitters before looking for anything else. Make sure the batteries in the RKE transmitters are good and replace them if in doubt. Here's the procedure for programming the RKE transmitters.

Up to 4 Transmitter Identification Codes (TIC's) can be programmed into the receiver at any given time.

1. Open the driver's door of the vehicle. Leave it open through the programming procedure.
2. Move the mechanical door lock lever to the LOCK position.
3. Insert the ignition key and turn it to the RUN position.
4. Turn the ignition to the RUN position. Within 20 seconds, aim a transmitter at the receiver dome and press the lock button, for at least 5 seconds. Once the receiver accepts the programming code the driver's door will unlock.
5. Once the first transmitter has been programmed, additional transmitters (up to 4) may be programmed into the receiver. Within 20 seconds of the previous transmitter programming, move the mechanical door lock lever to the Lock position. Aim another transmitter at the receiver dome and press the LOCK button for at least 5 seconds. The door lock will cycle again.
6. To lock the programmed codes into the receiver, the ignition must be turned off and back on within 20 seconds after programming the last transmitter's code. At that time, all previous codes are erased from the module.

If the alarm still doesn't work correctly, you probably have a bad Alarm Module. If you wanna download this procedure, clic the image.

79482d7.gif

Enjoy Jeep.

on Sep 23, 2009 | 1993 Jeep Grand Cherokee

1 Answer

How do you program a keyless entry remote for 1998 Jeep Grand Cherokee


someof them you cant you have to take it to the dealership

Jan 17, 2012 | 1998 Jeep Grand Cherokee

1 Answer

1997 jeep will not start thinking its the anti theft lock but dont not how to reset the code ... does anyone know how


I would try reprogramming the Remote Keyless Entry (RKE) transmitters before looking for anything else. Make sure the batteries in the RKE transmitters are good and replace them if in doubt. Here's the procedure for programming the RKE transmitters.

Up to 4 Transmitter Identification Codes (TIC's) can be programmed into the receiver at any given time.

1. Open the driver's door of the vehicle. Leave it open through the programming procedure.
2. Move the mechanical door lock lever to the LOCK position.
3. Insert the ignition key and turn it to the RUN position.
4. Turn the ignition to the RUN position. Within 20 seconds, aim a transmitter at the receiver dome and press the lock button, for at least 5 seconds. Once the receiver accepts the programming code the driver's door will unlock.
5. Once the first transmitter has been programmed, additional transmitters (up to 4) may be programmed into the receiver. Within 20 seconds of the previous transmitter programming, move the mechanical door lock lever to the Lock position. Aim another transmitter at the receiver dome and press the LOCK button for at least 5 seconds. The door lock will cycle again.
6. To lock the programmed codes into the receiver, the ignition must be turned off and back on within 20 seconds after programming the last transmitter's code. At that time, all previous codes are erased from the module.

If the alarm still doesn't work correctly, you probably have a bad Alarm Module.
Click here also; http://www.scribd.com/doc/20110658/Keyless-Entry-System-Jeep-Grand-Cherokee

Oct 05, 2010 | 1997 Jeep Cherokee

1 Answer

1994 Jeep Cheerokee Laredo: The remote keyless


If it is a factory alarm you can't unhook it. Replace the switch attached to the lock cylinder inside the door. In the meantime, the switch on the passenger door may still be good. Cycle the key in the passenger door to see if it turns off the alarm.

Oct 16, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Keyless remote


try this I can get you more info if needed have a good day DB
Notes SYNCHRONIZATION (ROLLING CODE) BUTTON TRANSMITTERS
The transmitter code will go out of synchronization if the button is pressed more than 255 times outside the range of the receiver which is inside the Door Module. In other words the transmitter will not work. To synchronize the code of the particular transmitter with the receiver, press and hold both lock and unlock buttons simultaneously for 5 seconds . Release the buttons and wait until the doors unlock indicating that the code has been synchronized. This may require waiting for as long as 6 minutes .

Feb 15, 2009 | 1997 Jeep Grand Cherokee

1 Answer

Keyless remote transmitter programming


You will have to have a Jeep/Chrysler/Dodge service tech hook up their programed OBD2 scanner to reset.

Jan 27, 2009 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

620 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...