Question about 2007 Audi A3 2.0

Open Question

Audi A3 07 my blower only blows on number 4 setting whats the problem

Blower works fine on No4 setting but does not work on 1.2.3. setting

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

peidavey
  • 14 Answers

SOURCE: replace blower motor

check out http://forums.audiworld.com/forum

tons of help to be had there.

Posted on Dec 31, 2008

chain saw
  • 94 Answers

SOURCE: Front screen demister on Audi Avant A4 2004

ONE OF THE HEATER DISTRIBUTION FLAP MOTORS FAULTY.UNSCREW GLOVEBOX AND YOU WILL SEE THE ONE THANS NOT WORKING(TURN ON BLOWERS TO TEST)

Posted on Feb 18, 2009

chain saw
  • 94 Answers

SOURCE: audi a4 front de-mister problem

ONE OF THE HEATER DISTRIBUTION FLAP MOTORS DEFECTIVE. UNSCREW GLOVEBOX AND YOU WILL SEE THE MOTORS.TEST WITH THE BLOWERS ON ,TRY EACH VENT TO FIND FAULTY MOTOR...

Posted on Feb 18, 2009

  • 1 Answer

SOURCE: 1997 Audi A4 2.6- heater blower working

check if you can here the fan running. If not the cause can be that the bushes have reached there limit and need to be replaced. If you have the time and tools, you can remove the motor and get to the bushes. You will find that they have been worn down to a curn shape. If you remove each bush, and flip it 180 degrees, then the tip of the bush will make contact with the motor shaft. This will give you many months of fan life and save you a packet. You could also replace the buses with new ones - Audi do not sell them but can be matched by good auto shops.

Posted on May 08, 2009

VAGMatt
  • 31 Answers

SOURCE: Hi I have a 1998 audi a4 and the blower motor

Hi, first off, check to see if there is anything else on the same circuit, e.g is everything else working with the fuse blown. The cigarette lighter is a favorite. If everything else is ok, use a a multimeter set to amps from the positive battery terminal to the heater motor input terminal (with a suitable fuse in line) to test the amps draw of the motor. You can then compare this with the fuse rating recommended and if it's greater than 2/3 of the fuse rating, then replace the motor. e.g 10 amp fuse 7 amps max loading, 15 amp fuse 10 amp loading.
Hope that helps Matt..

Posted on Nov 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater setting not working correctly, wont work all the time


Blower motor relay , resistor , control module . any one of these could be the culprit . You have to test to determine which one is at fault ! Do you have a DVOM - digital volt ohm meter an do you know how to use it ? Heater Blower Motor Troubleshooting Blower Motor Problems Auto Repair Help

Jan 12, 2016 | 2003 Chevrolet TrailBlazer

2 Answers

Heater won 39 t blow on 5


haw i fix my rpm meter problem

Sep 28, 2013 | Cars & Trucks

1 Answer

My blower fan only works on 3/4/5 settings not 1/2 settings


I would say it is the switch or the resistor.
A mechanic would check for voltage at the resistor on each speed.

Jul 16, 2012 | 2001 GMC Yukon

1 Answer

What's wrong with my blowers


heater blower motor resistor is bad it is located somewhere on the outside of the heater box.it is not part of the blower motor itself.buy a new one and look for the same on your car.this is absoulutly what the problem is

Jun 05, 2012 | 2005 Kia Carens 2.0

2 Answers

2002 Pontiac air settings 1,2 and 5 don.t work on my A/C and Heater


Your blower motor resistor module has failed. You can replace it with a little effort. The cost is around $35 to $40.

Nov 20, 2011 | 2002 Pontiac Grand Prix

1 Answer

Blower does not turn on when put on settings 1-3, but will on setting 4. Also, a/c compressor turns on with settings 1-3 but off on setting 4 which is the only one that blows air. What could this be?


it sounds like your resister pack is bad its a small module usually located by the blower moter replace that and it should work just fine

i hope this helps

Aug 06, 2010 | 2006 Nissan Xterra

1 Answer

A/C blower problem, replaced resistor, now what?


2006 monte carlo the fresh air taps after the car off for 5 secs

Mar 09, 2010 | 2002 Chevrolet Monte Carlo

2 Answers

Blower speed question (ac/heater). This just


This is definitely 100% the Blower Motor Resistor.
Replace this and all speeds will work fine.
This Resistor is defined with 3 to 4 wires going into it, and is located adjacent to the Blower Motor.
It is easily access, removed and replaced.
I will post an additional comment on Part Number, Price and where available.
Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Feb 19, 2010 | 1999 Jeep Wrangler

1 Answer

Heater only works on 5 settings 1-4 don't work


you need to change your blower motor resistor it should be located neer or on the blower motor housing.

Dec 30, 2009 | 2000 Chevrolet Impala

Not finding what you are looking for?
2007 Audi A3 2.0 Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14228 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...