Question about 1996 Land Rover Range Rover

1 Answer

Drivers door on p38 super locked how do i open it

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Turn key in unlock position and hold for 3 seconds.

Posted on Oct 21, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 740 Answers

SOURCE: range rover p38 central locking not working on

souds like you either have a broken wire in the door or the motor that controls that lock is bad

Posted on Mar 05, 2010

  • 383 Answers

SOURCE: 3 beeps when I swing a corner or hit a bump

its a convenience sensor have a dealership take a look at it its a range rover these things are made for people with money and the australian outback

Posted on May 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you enable a range rover engine when key battery is flat


There is a sequence of left and right turns of the key in the driver's door that will reset your bECM (Rovers brain) if the following have been tried.
1. Replace batteries in remote and 're-sync by depressing lock button on remote while physically turning and locking the door. Don't release button until locked and key removed. Repeat for unlock button.
2. Disconnect negative/earth cable from battery. While disconnected open driver's door, turn ignition to position 2, return to battery leaving driver's door open and reconnect the negative cable. Proceed to ignition. Turn off completely. Close all doors and hood and attempt starting.
Should both of these methods fail, run a search here on fixya for "engine disabled Range Rover P38" This will take you to step by step instructions on resetting the bECM which I opened this post with. It has been covered many times here, including by myself, no reason to post it again.
Good Luck!

Jul 14, 2014 | 2000 Land Rover Range Rover

1 Answer

Range rover p38 problems


I have the same problem sometimes
1 Check the condition of your battery, if old, it will not give full power required to communicate with the security system.
2 If you don't have the EKA of your RR, try this next time you get caught, put key in the drivers door look, press unlock button on key fob and at the same time turn to unlock, if all locks unlock then the engine should not be immobilized - Good luck

Jul 13, 2014 | 1996 Land Rover Range Rover

1 Answer

How to reset engine disability in 1996 Range Rover?


Lock doors with the key. Take out key . Insert key open and close lock 5 times then on the fifth turn open door this will reset the disable code to normal . I had this code on my P38 Range Rover and the Rover Tech assisted me with this simple way to reset the engine disable fault code . Good Luck .

Apr 23, 2014 | 1996 Land Rover Range Rover

1 Answer

3 beeps when I swing a corner or hit a bump


its a convenience sensor have a dealership take a look at it its a range rover these things are made for people with money and the australian outback

May 27, 2010 | 1999 Land Rover Range Rover

1 Answer

Range rover p38 central locking not working on drivers door, and boot, remaining three doors working perfectly, thanks sharon


souds like you either have a broken wire in the door or the motor that controls that lock is bad

Mar 05, 2010 | 1999 Land Rover Range Rover

1 Answer

Need to remove the driver's side inner door panel to replace the door lock due to vandalism of the lock


CLIP OFF COVER ON DOOR HANDEL /REMOVE BOLTS FROM HOLES IN HANDEL/ PUSH UP ON PLASTIC RING ON WINDOW WINDER NOW PRISE OPEN DOOR PANEL FROM DOOR.

Oct 21, 2009 | 2005 Ford F 250 Super Duty

Not finding what you are looking for?
1996 Land Rover Range Rover Logo

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

80608 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...