Question about 1996 Chevrolet Tahoe

1 Answer

Transfer case fuse blows when engaging four wheel drive.

I replace the fuse and the 2WD light comes on. When I push the 4WD button, it blows the fuse and four wheel drive does not engage

Posted by on

  • Anonymous Mar 28, 2014

    stuck in four wheel drive need to get back in two but keeps blowing fuse. uv is gone on drivers side messed up need help.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 195 Answers

Hello;
Sounds like yoou have a short either in the switch pod or in the 4wd electrics. Check for pinched wires or bare wires grounding out at the front axle and at the transfer case.
Thanks;
Rich
RPM Northwest

Posted on Jan 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Got. A 2003 f150 4x4 got problems with 4 wheel drive locking in and stay in drive shaft turning front wheels not


Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).

Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem ( this is what you seem to have, the transfer case is engaged and will drive the front shaft mine was a key on engine off test ).

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
sscullys_185.jpg
-- If the vacuum shift motor does not move:
1.Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
2.Check the fuses for the 4WD system and the solenoids.
3.Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
sscullys_187.jpg
4.Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
5.Check the vacuum reservoir box for cracks.
6.Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
7.Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
sscullys_186.jpg

Usually the case is cracked vacuum lines from the solenoids, the next common is a cracked vacuum reservoir box, and 1 time I have seen the mount for the vacuum disconnect motor broken ( motor floating free so it could not push against the axle )
sscullys_188.jpg

Aug 28, 2011 | 2003 Ford F150 Regular Cab

1 Answer

KinlogworksI have A 2003 F-150 Super Crew. I have only used th4 wheel drive a few dozen times. about a mounth ago i switched it into 4 high and nothing happened. problem also in 4 low. any advise?


Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ). The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).

Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
{ picture of shift motor }
-- If the vacuum shift motor does not move:
•Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
•Check the fuses for the 4WD system and the solenoids.
•Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
•Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
•Check the vacuum reservoir box for cracks.
•Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
•Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
{ Picture of Vacuum diagram )

- If the front drive shaft turns:
•For ESOF system
-- Check the fuses for the transfer case, engine compartment fuse panel, 17 & Cab fuse panel fuses 13 and 23 ( verify with owners manual, 97-97 & 99-03 MY can be slightly different on some items ).
-- Try hitting the transfer case with a dead blow hammer ( do not use a metal hammer, it can damage the transfer case ) to see if the transfer case shift motor is hung up .
-- Check the transfer case connector, to make sure the connector pins are clean and making good contact.
•For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

Jan 18, 2011 | 2003 Ford F150 Regular Cab

1 Answer

2003 F-150 regular cab automatic transmission and the 4WD will not engage.


Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).


Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
{ picture of shift motor }
-- If the vacuum shift motor does not move:
•Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
•Check the fuses for the 4WD system and the solenoids.
•Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
•Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
•Check the vacuum reservoir box for cracks.
•Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
•Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
sscullys_111.jpg

- If the front drive shaft turns:
•For ESOF system
-- Check the fuses for the transfer case, engine compartment fuse panel, 17 & Cab fuse panel fuses 13 and 23 ( verify with owners manual, 97-97 & 99-03 MY can be slightly different on some items ).
-- Try hitting the transfer case with a dead blow hammer ( do not use a metal hammer, it can damage the transfer case ) to see if the transfer case shift motor is hung up .
-- Check the transfer case connector, to make sure the connector pins are clean and making good contact.
•For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

Jan 10, 2011 | 2003 Ford F150 Regular Cab

2 Answers

Front axle does not engage. Push 4hi or 4lo button, transfer case motor engages front drive shaft, front diferential actuator extends, but no 4 wheel drive. What do I check next?


There may be vacuum lines running down to the hubs. If so check them for vacuum when engaging and dis-engaging 4 wheel. If you can't feel any vacuum, trace lines, and check for leaks.

Dec 13, 2010 | 2002 Chevrolet Silverado 1500HD

1 Answer

My 2001 silverado w/69,000 miles has no light indicating 2 or 4 h


THE TRANSFER CASE MOTOR IS NOT WORKING TO INGAGE 4 WHEEL DRIVE. CHECK WITH DOOR OPEN WHEN YOU PUSH 4 WHEEL SWITCH YOU SHOULD HEAR MOTOR INGAGE 4 WHEEL DRIVE. IF YOU HEAR MOTOR BUT STILL NO 4 WHEEL DRIVE THE GEAR ON MOTOR COULD BE DAMAGED. REPLACE TRANSFER CASE MOTOR.

Jan 08, 2010 | 2001 Chevrolet Silverado 1500

2 Answers

My 1999 chevy silverado 1500 four wheel drive won't engage. The truck is in 2wd now. When I push 4wd hi or low, I can hear the actuator try to engage the four wheel drive. The four hi or low button will...


You probably have a bad encoder motor.It is located on the side of the transfer case on the drivers side.It is black.The other problem they had with these was the switch but you have already replaced this so your next thing is the encoder motor.Hope this helps.Good luck.

Dec 28, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

I tried to put a 2001 chevy suburban 2500 in four


check the actuator in the front diff to see if it is working

Jul 12, 2009 | Chevrolet Suburban 2500 Cars & Trucks

1 Answer

1999 Jimmy 4wd not engaging. It has push button


could be your front actuator or your actuator motor on the transfer case.

Apr 12, 2009 | 1999 GMC Jimmy

Not finding what you are looking for?
1996 Chevrolet Tahoe Logo

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...