Question about Cars & Trucks

1 Answer

Just purchased genuine part oil filter for my o2 micra auto and it wont screw right down by about 6mm, am i missing something out?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 373 Answers

Did you check and see if the filter still has the rubber grommet by the threads? Look at your old filter to make sure they are the same. Did you get it on cross threaded? . Might just be a bad filter, seen it happen only once. . Did you leave the old rubber grommet on the threaded shaft? Just shooting some guesses at you. Good luck

Posted on Jan 08, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Hentie
  • 18 Answers

SOURCE: What type of Auto Gearbox Oil Should I use for a 2001 Nisan Micra

You could fill it with automatic transmission fluid called ATF or oil called Dextron 2

Posted on Jan 15, 2009

TDISLine
  • 1874 Answers

SOURCE: We have a problem with a 4jx1 after we changed the

Isuzu Trooper 3.0 DTi, 118 kW (160 HP), 4JX1 engine code:

Here you have the free download internet address for the repair manual:

http://www.jeepolog.com/UserFiles/downloads/trooper_manual.pdf

Please do rate my response. Thanks!

Posted on Nov 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I install a new filter on a mazda b 2300 series pick up truck


well it certainly depends on what filter you are going to change .

Mar 29, 2015 | Mazda Cars & Trucks

1 Answer

How to change gasket on oil cooler 2001 Kia Sportage?


An "O" ring can be purchased at your local auto parts along with your oil filter. Your oil filter screws on top of your oil cooler. Mine leaked as well. A new "O" ring and filter screwed on tightly solved my problem.

Jun 22, 2014 | 2001 Kia Sportage

1 Answer

How to remove oil pan


jack it up, drain oil from drain plug on oil pan when drained remove and replace oil filter also. remove the pan bolts pull off pan and gasket.put new oil pan gasket on if needed.when oil pan bolts are back in, screw them in hand tight, then torque them down to specs and alter nate the tightening so it wont damage pan seal. any auto parts store can tell you the torque on the bolts for your car. good day!

Mar 31, 2014 | 1999 Chevrolet Venture

1 Answer

When I change oil ,oil filter is like new.no oil inside.


ensure that the filter you are using are good quality with anti bleed down valve in them. If the filter is a side screw on or a screw down then if the filter is wrong , the oil will drain back. If the filter is right one then I would be concerned as the filter is right after the oil pump and be full of oil. take a used filter that looks clean and using a hacksaw or other suitable tool cut the tin casing off and see if there is oil inside in the paper element. and go from there.

Mar 14, 2014 | Cars & Trucks

4 Answers

Nissan micra k12. not idling properly, low power, not staring all the time. continuous problem. replaced throttle with 2nd hand part. better for a while. now car wont start, if it does it hunting,(sound...


HI, I GOT NISSAN MICRA 1.2 SE 2005 PLATE ONLY DONE 59000 MILES. MISSING! I HAVE CHANGED COIL PACKS, CAMSHAFT SENSOR, TIMMING CHAIN, STILL THE SAME PROBLEM. I HAVE ALREADY SPENT 1000.00 POUNDS. IS THERE ANYONE WITH SAME PROBLEM?

Jan 29, 2010 | Nissan Micra Cars & Trucks

1 Answer

Can a screw on type oil filter replace factory element type?


I would not change anything on your 2009 vehicle until it is out of warranty. If something goes wrong the dealer could deny warranty coverage. I know of no one making a converion kit to a spin on filter. Many auto makers are going to cartridge style oil filters that cost more. Most auto parts store carry you filter.

Please let me know if this information is helpful. Positive feedback is appreciated. Thank You!

Mar 20, 2009 | 2009 Mazda Tribute Hybrid

1 Answer

I cannot seem to find the air filter on my 320d bmw


Hi FTjoe , the air filter on this vehicle is located under the upper engine covers on the left hand side of the engine. to gain access to this item you will need to remove, the microfilter housing ( held in by 4 x t27 torques screws, upper engine cover (held down with 5 x 6mm hex bolts and the small engine cover a the back of the engine 2 x 6mm hex bolts. remove the air intake trunking that sits on the front slam panel and goes to the air filter housing by meens of a flexi square pipe, once this is removed you will need to remove the air filter cover 5 x 6mm hex bolts, then you should be able to replace the filter, once fitted all removed parts are reinstalled in reverse order, hope this is of some help, regards mark.

Jan 27, 2009 | BMW 318 Cars & Trucks

1 Answer

Over heating and oil mixing


yes sounds good to me also check the oil cooler which is what the oil filter screws onto with water pipes connected as well,as normally the auto connection into the radiator doesnt give problems when its copper but a lot of new cars use plastic and they are absolutly useless.this oil cooler on top of the oil filter is often damaged by heavy handed mechanics hammering a screwdriver into the oil filter to remove it and make a hole into the oil cooler .

Nov 18, 2008 | 2001 Volkswagen Beetle

1 Answer

What type of Auto Gearbox Oil Should I use for a 2001 Nisan Micra


You could fill it with automatic transmission fluid called ATF or oil called Dextron 2

Nov 12, 2008 | 1988 Nissan Pulsar

2 Answers

Instructional guide oil change


Check your owners manual for the following info: Engine oil requirements, which would be what engine oil weight is right for your car. It will be #'s such as 5W 30. Use the weight recommended by chevy. The manual will also tell u how much u need. Go to an auto parts store, where u will need to purchase the following: 1. engine oil (they should be able to look up the weight requirement for your car, 2. oil filter, get a quality filter. An easy way to determine that is the weight of the filter. A good filter has a valve in it to prevent oil from draining out when the engine is off. This way when u start the car, u have oil pressure right away. You can also ask for advice on what they feel is a good filter.3. Filter wrench, to remove the oil filter. You can determine the correct size by seeing if it fits on the new filter. Ok, take it all home and: the car should be at operating temperature, either jack up the car or buy a set of ramps to drive it up on so u can get under the car. Make sure the car is supported on safety stands, never go under a car w/ just a jack holding it up. Block the rear wheels front and back so the car can't roll, put the emergency brake on, leave it in gear if it's a standard trans, in park for auto trans. Go under the car to remove the oil pan drain bolt. Be careful as surfaces and oil will be hot. Have a good size plastic pan, or something similar (u can also buy a oil drain container especially made for this) under the car. Remove the drain plug, letting the oil drain for 15 minutes or so, to let it drain completely. The reason u drain it w/ engine hot is to drain the oil quickly and completely, cold oil would take a long time to drain. Remove the oil filter w/ your wrench. I assume your filter is accessed from under the car. A few (not many) allow u to remove the filter from above in the engine compartment. With a clean rag, wipe off the area where the oil filter screws on. Make sure the old gasket isn't stuck on (rare, but it does happen). Also clean the area around the drain bolt. Replace the drain bolt, do not use brute force to tighten it, you want it on good and snug, not loose or so tight you ruin the threads. Now coat the gasket on the new oil filter w/ new clean engine oil, screw on hand tight. Go by the oil filter instructions on the box, usually u tighten til it just makes contact w/ the engine, then tighten one half to one full turn more.
Add the required amount of oil, start up and let it run for a few minutes, check for any leaks. Check your level several times a month so u know how often to add oil. U shouldn't wait 'til its down a quart to add oil, if its down half a quart, top it off. Your engine will reward u with a long life w/ this care (change every 3k miles). Don't overfill ever, as too much oil is bad for the engine, it causes the oil to foam, and u loose your lubrication. Many garages, town and city recycling centers, oil change shops will accept used oil to recycle. Whoa! seems a lot more complicated than it really is! Let me know if u have any questions. countrycurt0

Oct 05, 2008 | 2001 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...