Question about Chevrolet Corvette

Open Question

HOW TO REMOVE WIPER ARMS 1984 CHEVY TRUCK - Corvette Chevrolet Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 71 Answers

SOURCE: how do you remover the wiper arms?

Yes you must remove the arms, to do so, just use a standard screw driver to remove the caps covering the arm securing nuts on the arm drive shaft. The arms are secured on the shaft by splines and you should mark the arms in order to replace them in the exact position they are removed on drive spline. Lift the arms all the way up to avoid the spring tension when removing from the spline. Then you will need to remove the other panels that cover the motor and arm power shafts etc. Hint... disconnect as little as possible to accomplish the swap.

Posted on Jan 08, 2009

66 chrgr
  • 1011 Answers

SOURCE: wiper arms

at the end of the wiper arms lift up the covers there u find the nuts.

Posted on Jan 25, 2009

lesabre1972
  • 474 Answers

SOURCE: Removing wiper Arms from 2006 Jetta TDI

You will need a wiper arm puller to get these off or go back to where you had the work done and have them fix it seen as how they messed it up in the first place.

Posted on Mar 29, 2009

  • 54 Answers

SOURCE: remove front wiper arms. Lift arm, slide out

Just pry them off. Make sure the tab is out the whole way. Sometimes they can be tough to get off. Spray with wd40 it should aid in getting it loose. You could even tap it a few times with a rubber mallet or a light hammer, just be careful. Good luck if this helps let me know.

Posted on Jun 19, 2009

ftw1952
  • 10319 Answers

SOURCE: How do you remove the windshield wiper arms

The wiper arms have a push in tab at the very bottom at the fitting that is pressed into the wiper linkage below the screen. Use a flat headed screwdriver to pry out the tab. Once out the arm can be pulled right off. Now you can remove the cowling screen

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My wipers are not working on my 1984 dodge pick up. I looked into the grill cover where the window meets the hood, and I can see that the rod that moves the wipers is disconnected from the motor. I can...


I believe that when you hinge the arms forward and look down at the inside, bottom of the arms(at the base) you should see a small trigger mechanism....depress that and pry your arms off at the base with a screwdriver, now the arms are splined so they will only slide off that spline one way,and that makes it easy to re-install them, hope this works for ya.

Mar 15, 2011 | 1984 Dodge D150

1 Answer

How to remove the wiper switch in a 1984 chevy truck


Remove dash bezel . Remove plug from switch itself. Remove screws holding switch in place. Repeat process to re-assemble.

Mar 15, 2011 | 1984 Chevrolet Chevy

1 Answer

Ever since i replaced the wiper motor on 2003 chevy impala the wipers stop in up position instead of down position when stop- ped on delay position.is it something i did wrong when replac- ing the...


try this fix
remove wiper arms from where they connect on car
turn wiper moter on then off. turn ignition off
if wiper motor is good it should put spline in off position and now all you need to do is replace wiper arms in the correct position they would be in when wipers are turned off

Dec 14, 2010 | 2003 Chevrolet Impala

1 Answer

Delay wipers only work on high speed on 2000 chevy silverdo 1500 truck no delay


Hello, my name is Ben and I can help you with this problem. This is a very common problem with Chevy. You need what is known in most vehicles as a "pulse board". The pulse board is located inside the wiper motor control module. On many vehicles the pulse board is replaceable, unfortunately on your Silverado you must replace the entire Wiper Motor Control Module which is bolted onto the top of the wiper motor. To get to the wiper motor, first remove those little nut covers on the big end of the windshield wiper arms, if you slip a small screwdriver or your fingernail they just pop off. Now unbolt the windsheild wiper arms, before removing the wiper arms, mark their location on the windsheild with a grease pencil or magic marker. The arms are hard to remove, you need to kinda wiggle and pull at the same time, now that long plastic cowl needs to come off, those clips at the front edge just slide forward, then at each end lift up that rubber flap and remove those TORX screws. Remove the cowl and set it somewhere SAFE, it's easy to break. You will now see the control module mounted on the wiper motor, unplug the electrical connections and remove the TORX screws holding it to the motor. Assembly is the reverse of dis-assembly. If you have any trouble or questions, feel free to ask, Ben.

Nov 13, 2010 | 2000 Chevrolet Silverado

1 Answer

WINDSHIELD MOTOR REPLACEMENT FOR MY 2000 CHEVY C3500 HD


REMOVAL PROCEDURE
  1. Remove the wiper arms.
  2. Remove the air inlet grille panel.
  3. Disconnect the electrical connector from the motor. IMPORTANT: Do not remove the crank arm.
  4. Loosen the nuts attaching the drive link brackets to the crank arm.
  5. Remove the brackets from the wiper motor crank arm.
  6. Remove the three bolts and the wiper motor from the vehicle.
INSTALLATION PROCEDURE
  1. Install the wiper motor on the vehicle. NOTE: Refer to Fastener Notice in Service Precautions.
  2. Install the three bolts. Tighten Tighten the three bolts to 7 N.m (62 lb in) .
  3. Install the drive link brackets to the wiper motor crank arm with the right side linkage closest to the wiper motor. Tighten Tighten the link nuts to 5 N.m (44 lb in) .
  4. Connect the electrical connector to the wiper motor.
  5. Install the air inlet grille panel.
  6. Install the wiper arms.

May 10, 2010 | 2000 Chevrolet 3500

1 Answer

How do you remove the windshield wiper arms


The wiper arms have a push in tab at the very bottom at the fitting that is pressed into the wiper linkage below the screen. Use a flat headed screwdriver to pry out the tab. Once out the arm can be pulled right off. Now you can remove the cowling screen

Apr 07, 2010 | 1987 Chevrolet S-10 Pickup

1 Answer

What is the 94 Chevy Caprice Classic wiper arm


heres a wiper linkage asm diagram, the wiper washers are on the hood or on the cover to deck,then the hose runs through the wiper arm to a nozzle, if you remove the arms you can lift cover enough to look at the hose to washer connection,also check hose to arm they often break there good luck.2d8c418.gif

Mar 30, 2010 | 1994 Chevrolet Caprice Classic

1 Answer

How do i install a new wiper motor on my truck?


you have to remove the cowl (panel under wiper arms) by removing the wiper arms and taking off the screws in cowl. The wiper arms need to be pulled away from windshield then you slide the clip at the base over and pry the wipers off. Under the cowl is a screen you remove. Then you can get to the wiper linkage. You can pop off the linkage with a prybar or a big screwdriver. Once it's off you take the bolts holding the motor out unplug the connector and reverse order for installation. The linkages can take some serious manhandling to get back on!

Feb 07, 2010 | 1993 Dodge Dakota

1 Answer

1984 S10 wiper arms


No Problem! Look down on the Bottom of the Wiper Arm, wher it attaches and Swivels. There is a Small tab that comes off of the Upper Part of the Arm that looks like Two Front Teeth Sticking up just a Little. Take a Pair of Pliers and Pull this Tab Up Towards the Top of the Winshield to Release the Lock on the Arm. then take a Pair of Pliers with Tape on them so that you will not Scratch the Arm and Pull while you Wiggle the Arm right at the Swivel Pont and they will Come off. Please Rate my Response, I need all the Help That I can Get! Thanks!

Jan 28, 2009 | 1984 Chevrolet S-10

1 Answer

1984 chevy S10 windshild wipers


at the arm remove the cap on end and their is a nut remove it 10 mm / Please rate my response thank you very much

Jan 28, 2009 | 1984 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...