Question about Cars & Trucks

Open Question

2001 Mitsubishi Montero Rear wheel bearing replacement

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2001 Mitsubishi Montero Limited. 122k miles.

2003 Mitsubishi Montero Limited. 97k miles. Temp gauge is erratic when actual temp is normal. How do I fix this?

Posted on Dec 31, 2009

Ad
losflip
  • 94 Answers

SOURCE: 2001 monte carlo ss. Rear wheel bearings making a grinding noise

It is pretty easy, there is not much labor involved if it has anti-lock brakes in the rear you will also have to un-plug the wire harness attached to hubs.

Posted on Nov 26, 2008

  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

  • 101 Answers

SOURCE: how do i replace the rear wheel bearing on my peugeot 206

wheel off remove the tin cap in the centure of the hub undo the big nut put the wheel back on with just 2 bolts finger tight so you can pull the hub off.once the hub is off take the 2 wheel bolts back out.now look in side the hub were the big nut was and you will see a sir clip take that out.then use a socket and a bench vice to press the old bearing out.use the socket and bench vice to put the new bearing back in.

Posted on Aug 01, 2009

  • 27 Answers

SOURCE: replace rear wheel bearing 2002 ford explorer 4x4

you must remove brakes, then remove axle nut, then remove upper control arm and finally tie rod stabilizer, remove axle from car then bearing can be accessed. this is a difficult job that requires special tools so be careful

Posted on Aug 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace front bearings on 2001 mitsubishi montero sport?


Have them replaced

Go to You Tube Video & watch how

Do both sides

I would got to a local shop that has been there for
20 years,not a franchise

Jul 26, 2014 | 2001 Mitsubishi Montero Sport 4WD

1 Answer

I have a 98 mitsubishi montero sport having it serviced mecanic said carrier bearing is going out. I thought thayt was just on big trucks with split drive shafts. is there one on my suvh


You will need a blanket and a flashlight.
One way to get the truck high enough to look under it is to drive either the right side wheels or the left side wheels up onto a curb.
Then get under it and look halfway between the end of the transmission and the rear axle pumpkin.
A carrier bearing is the round thing about half way between these two.
Just a little more information.
The carrier bearing is found roughly about the place where the back of the front seat is above you. The carrier bearing is likely the size of a breakfast cereal bow,l, .
The pumpkin is the big gear holder exactly in the middle between the rear wheels, and is about the size of a large dinner plate.
Your vehicle is old enough to need one if you have not had it replaced yet.
These normally will give you some notice of their failure, such as a vibration or noise of some kind, be not in every case.
Be blessed.

Feb 01, 2013 | 1998 Mitsubishi Montero Sport

1 Answer

How do I pull/replace rear wheel bearings on 1995 Mitsubishi Montero sport?


i assume you mean **** when you type *****,just say ****.this sounds like the rear tires may be out of blance or has a defect in the tire(s).a wheel bearing won`t cause a vibration unless the bearing is so bad its about to or is coming apart.a wheel bearing will make a noise like a humming or growling noise.have teh wheel balance check and the condition of the tires checked for belt separation or bulges.

Oct 27, 2011 | 1995 Mitsubishi Montero

1 Answer

I need to know how the front bearings look for a 2002 montero sport


YOU HAVE 2 BEARINGS INNER AND OUTER BEARING IN HUB.YOU NEED TO REMOVE BRAKE CALIPER THEN REMOVE GREASE CAP.STRAIGHTEN THE BEND COTTER PIN THEN REMOVE COTTER PIN.THEN LOOSEN REMOVE ADJUSTING NUT AND WASHER FROM END OF THE SPINDLE.PULL THE HUB OUT SLIGHTLY THEN PUSH IT BACK INTO ORIGINAL POSITION. THIS WILL FORCE THE OUTER WHEEL BEARING OFF THE SPINDLE ENOUGH SO YOU CAN REMOVE IT.PULL THE HUB OFF THE SPINDLE.USE A SCREW DRIVER TO PRY THE GREASE SEAL OUT OF THE REAR OF THE. HUB AS THIS IS DONE NOTE HOW THE SEAL IS INSTALLED.THEN REMOVE THE INNER WHEEL BEARING FROM THE HUB.

Aug 25, 2011 | 2001 Mitsubishi Montero

3 Answers

2001 Mitsubishi Montero Limited. 122k miles.


2003 Mitsubishi Montero Limited. 97k miles. Temp gauge is erratic when actual temp is normal. How do I fix this?

Nov 13, 2009 | 2001 Mitsubishi Montero

1 Answer

2000 Montero Sport shutters/vibrates in 2 and 3 gears


Could be a wheel bearing and/or a rear differential pinion bearing, which usually get worse when under load(going up hill). I would definitely start there.

Aug 07, 2009 | 2002 Mitsubishi Montero

1 Answer

How to change rear wheel beqarings in a 2000


pretty simple they have rotors like front so remove caliper and rotor. make sure rotor is clean when u put new seal and bearings in. also hand pack wheel bearings with grease.

Feb 25, 2009 | 2001 Mitsubishi Galant

2 Answers

Replace front wheel bearings 1998 lancer


how do i remove the front wheel bearing hub assembly?

Aug 14, 2008 | 2001 Mitsubishi Montero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...