Question about Cars & Trucks

Open Question

Replace front wheel bearings on 2005 4wd Toyota 4Runner

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 24 Answers

SOURCE: replace front wheel bearings

The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Posted on Jun 20, 2008

Ad

SOURCE: 2000 toyota echo, wheel bearings

I found this site to be very helpful with this job: http://www.toyotanation.com/forum/showthread.php?s=714b28cb1c3f77f992209de0bdbfbd13&p=2481776#post2481776

Posted on Sep 23, 2008

  • 19 Answers

SOURCE: Replacing front wheel bearing

The brake rotor needs to be removed, drive shaft nut in center of hub then 3 bolts hold the hub assembly to spindle from back side. if it has abs unplug it then some work will need to be done with a hammer and chisel to work the bearing out of spindle and axle shaft from bearing

Posted on Oct 16, 2008

Technopro
  • 243 Answers

SOURCE: replace font wheel bearing

What exactly is your problem? If you want help you need to give the chassis number and the engine number as well so that I can be specific and give you the right instruction. Cheers

Posted on Mar 21, 2009

  • 18 Answers

SOURCE: wheel bearing replacement left front

Diagnosing the bearings can be tricky depending on severity of wear. Typically - drone noise at highway speeds, squeeling, clicking or grinding noises at low speeds that reduce during braking, or pull off the wheel and brake assembly and check the bearing for slack or smoothness of rotation by hand. While doing this, check the brake assembly thoroughly - generally a more likely culprit of wheel noise.

Wheel bearing replacement is not for the novice backyard mech. - you will need pullers, press, etc. If you can get a rebuilt assembly - much easier.

Posted on May 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 Toyota 4 runner 2 wd front wheel removal


Install front wheel bearing hub assembly on a ... - YouTube

? 8:42
https://www.youtube.com/watch?v=LQ-DGdt2J2U
Mar 11, 2014 - Uploaded by Andy Taylor
... Install front wheel bearing hub assembly on a 2003-2014Toyota 4Runner .... Pressing a 2005 and up Toyota Tacoma,4Runner, FJ Cruiser 2WD or 4WD ... How to Remove & Replace a Toyota 4x4 Manual Locking Hub ...
images for 99 Toyota 4 runner 2 wd front wheel removal

Nov 26, 2015 | Toyota Cars & Trucks

1 Answer

Front end grind


Sounds like a wheel bearing.

Feb 20, 2010 | 1995 Toyota 4Runner

1 Answer

How do I get rotors off front of 87 4Runner?


From memory, to remove the front disc rotors, the hub has to be disassembled completely from the vehicle. The rotors bolt to the hub from behind. Start by removing the calipers, then start disassembling the free wheel hubs, bearings etc.

Jul 19, 2009 | 1987 Toyota 4Runner

1 Answer

Front end screams when in 4x4


SOUNDS LIKE U MAY HAVE FAILED BEARINGS, THEY WOULD BE THE ONLY THING THAT COULD MAKE THAT MUCH NOISE. REPLACE THE FRONT DIFFERENTIAL BEARINGS, ALL OF THEM.

Jun 02, 2009 | 1986 Toyota 4Runner

1 Answer

Wicked vibration in front driver side wheel


Make sure the balance weights are still there, they can fall off from time to time. If its not that, jack it up and spin the wheel to see if you have a "flat" spot on the tire. Next grab the tire on the top and bottom and shake it, if there is play in it then the wheel bearing in bad or the ball joints need replacing.

May 28, 2009 | 1986 Toyota 4Runner

1 Answer

Front brakes


Hi there;
To replace the front rotors on your truck you will need to remove the hub & bearings, yes, how-ever you should not have to replace the bearings. If you take it a-part & find there is metal filings inside, then you would want to. But if the grease is only dirty you should just clean off all the old grease & repack your bearings.

Word of caution: If you are not familiar with repacking & adjusting wheel bearings you may want to consult a local gaurage for a demonstration as if you do not do it properly you can cause a lot of damage to you & your truck.

Having said that, once you get the hub off you will see that the rotor is bolted to the hub. remove the bolts, install the new rotors & install & torque the bolts.
Hope this helps
Farrout!

Mar 17, 2009 | 1995 Toyota 4Runner

2 Answers

91 4runner 4 wheel problem


Hello;
It sounds like the front differential is going out. I would suspect a galled bearing or the bearings in the differential are going out.Hope this helps.
Please rate me highly;
Thanks;
Rich
RPM Northwest

Feb 12, 2009 | 1991 Toyota 4Runner

1 Answer

1993 Toyota 4Runner-Knocking noise-front end-cold weather


This is Caused By the Grease in the Spindle Bearings Getting frozen. Get it Greased up really Well and you Might need to Repack the Bearings on this side to Stop this and Stop further Damage to the Spindle.

Jan 17, 2009 | 1993 Toyota 4Runner

1 Answer

Front brake rotors 1995 toyota 4runner


If you have 6 bolts going around the center (manual lock in/lock out) hub, you are going to be there a while. The center hub needs to come off, and ALL of the internal wheel bearings need to come out. The whole locking hub must be removed in order get the rotor off. This is NOT an easy job, and you need a special tool to loosen/tightem the wheel bearings. Figure 2 hrs per side if you have all of the proper tools & skill level.

Sep 27, 2008 | 1995 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...