Question about 2007 Chevrolet Suburban Three-Quarter-Ton LS

Open Question

How to replace brake pedal position sensor on 2007 surburban

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: I need to replace Accelerator Pedal position Sensor

there is two little nuts on the bottom of the pedal itself just loosen the nuts and it comes right off.

Posted on Apr 29, 2009

carlsbiz
  • 1124 Answers

SOURCE: BRAKE PEDAL GOES TO THE FLOOR WHEN PRESSED 2001

Have you checked the break fluid ?

Or could be the master..

Posted on Jul 11, 2009

jturcotte
  • 8125 Answers

SOURCE: I have a 2007 Chevy

If it is a code P0226 I would not consider it a safety issue.


Throttle position (TP) sensor C/accelerator pedal

position (APP) sensor ? - range/performance problem


Possible Causes: Accelerator cable adjustment, TP/APP sensor

Throttle position (TP) switch C/accelerator pedal position

(APP) switch ? - range/performance problem
Accelerator cable adjustment, TP/APP switch

This might only be an adjustment issue--make sure the throttle cable isn't so tight that the throttle cannot fully close.
If the cable is OK, it is probably the accelerator position sensor under the pedal.
There are procedures for testing the unit that I will paste below if you care to try them.

If you just want a shop to fix it, the part is about $50 and labor should only be 30 minutes.


Operation The sensor is made up of the two individual sensors within a single housing. Each sensor has a unique functionality to determine pedal position. The APP system along with the Powertrain Control Module (PCM) is used to calculate and control the amount of acceleration and deceleration through fuel injector control.


Removal & Installation

  1. Remove the driver-s side knee bolster.
  2. Push down on the small tab and disengage the electrical connector.
  3. Remove the pedal bolts and remove the pedal and sensor assembly.
  4. Installation is the reverse of removal.

    5bcaece.gif

Fig. APP sensor mounting
Testing

  1. Install a 3 amp fused jumper wire between the 5-volt reference terminal of the APP sensor and 5 volts. Install a jumper wire between the low reference terminal and a ground.
  2. Sweep the sensor through the entire range while monitoring the voltage between the signal terminal and the low reference terminal with a digital multimeter. The voltage should vary between 0.30-4.98 volts without any spikes or dropouts.
  3. If the voltage is not within the specified range or is erratic, replace the accelerator pedal assembly.

Posted on Oct 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

07 cadillac cts has no brake light all fuses are good and replace the brake switch.still not working any advice


Stop Lamps
The brake pedal position sensor is a resistive device used to sense the action of the driver's application of the brake pedal. The brake pedal position sensor provides an analog signal that will increase as the brake pedal is pressed.
The brake pedal position sensor receives both a 5-volt reference voltage and a low reference signal from the electronic brake control module (EBCM). When the brake pedal is pressed, a variable signal is applied from the brake pedal position sensor to the EBCM through the brake sensor signal circuit. The fuse block left rear supplies battery positive voltage to the bass relay switch through the BASS fuse. One side of the bass relay coil is permanently grounded at G402. The EBCM supplies voltage to the bass relay coil upon receiving the signal from the brake pedal position sensor. The switch contacts of the bass relay close and battery positive voltage is applied through the bass relay switch to the center high mounted stop lamp (CHMSL), and to the turn signal/hazard flasher module through the stop lamp switch signal circuit. The ground for the CHMSL is applied from G402. The turn signal/hazard flasher module then supplies voltage to the left and right stop lamps in the tail lamp assemblies that have ground at G401 and G402. For export vehicles the stop lamps receive battery positive voltage directly from the bass relay.

Do you know where the rear fuse box is ? Check BAS fuse 15amp. and the bas relay , should be marked on the inside of the fuse box lid . The rear fuse box is located

Fuse Block - Left Rear
In the passenger compartment, under the left side of the rear seat at carpet
Power and Grounding Component Views
Electrical Center Identification Views
Fuse Block - Right Rear
In the passenger compartment, under the right side of the rear seat at carpet.

If fuse and relay are ok your best would be to take to a cadillac dealer .

Jan 19, 2017 | Cadillac Cars & Trucks

1 Answer

Where's is the fuse located for my brake lights on my 2007 Pontiac g6 and rear defrost fuse


Stop Lamps
your br
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5-volt reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery positive voltage to the stop lamps, transmission control module (TCM), engine control module (ECM), and stop lamp relay coil side. When the stop lamp relay receives battery voltage from the BCM, the relay coil is energized and the stop lamp relay switch contacts close applying battery voltage through the STOP LP fuse to illuminate the center high mounted stop lamp (CHMSL).
I'd say you have more then a bad fuse ,just reading how the brake lights function .You should have it hooked up to a professional grade scan tool ,one that can check for DTC'S - diagnostic trouble codes in the BCM - body control module !
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Brake Pedal Position Sensor parameter in the data list for the body control module (BCM).
  4. Apply and release the brake pedal.
Does the scan tool display a change in the voltage?

DTC B3903 Stop Lamp Relay Circuit DTC C0277 Brake Pedal Position Sensor Circuit
DTC C0278
Did you perform the Diagnostic System Check - Vehicle?
Go to Step 2
Go to Diagnostic System Check - Vehicle

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
Does the scan tool display DTC C0278 00?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections

3

Recalibrate the brake position sensor.

Circuit Description
DTC C0870
The body control module (BCM) applies a ground through the brake sensor reference low circuit to the brake pedal position (BPP) sensor. The BCM supplies a 5-volt reference through the brake sensor reference voltage circuit to the brake position sensor. When the brake pedal is being applied, the BPP sensor then sends a variable voltage signal through the brake sensor signal circuit to the BCM.
Circuit/System Verification
  1. Ignition ON, observe the scan tool Brake Lamp Cmd. parameter as you apply and unapply the brake pedal. The parameter should change between OFF and ON as the brake pedal is applied and released.
  2. ?‡'
    If the parameter does not change as the brake pedal is applied and released, refer to Brake Pedal Position Sensor (BPPS) Malfunction.

  3. With a scan tool, command the LR Stop/Turn Signal Lamp ON and OFF. The LR turn signal should turn ON and OFF when changing between the commanded states.
  4. ?‡'
    If the LR stop lamp does not illuminate when commanded, refer to Stop Lamps Malfunction.

  5. With a scan tool, command the RR Stop/Turn Signal Lamp ON and OFF. The RR turn signal should turn ON and OFF when changing between the commanded states.
?‡'
If the RR stop lamp does not illuminate when commanded, refer to Stop Lamps Malfunction.






I
I'd

Sep 26, 2015 | Pontiac Cars & Trucks

1 Answer

Where is the stop lamp or brake lamp fuse and panel for a 2007 cadillac cts?


Kevin , this is a very complex way of stoplamp control , I will post GM service Description and Operation of how they work an let you deside if you want to tackle this ! Do the center high mount brake lights work ?
The brake pedal position sensor is a resistive device used to sense the action of the driver's application of the brake pedal. The brake pedal position sensor provides an analog signal that will increase as the brake pedal is pressed.
The brake pedal position sensor receives both a 5-volt reference voltage and a low reference signal from the electronic brake control module (EBCM). When the brake pedal is pressed, a variable signal is applied from the brake pedal position sensor to the EBCM through the brake sensor signal circuit. The fuse block left rear supplies battery positive voltage to the bass relay switch through the BASS fuse. One side of the bass relay coil is permanently grounded at G402. The EBCM supplies voltage to the bass relay coil upon receiving the signal from the brake pedal position sensor. The switch contacts of the bas relay close and battery positive voltage is applied through the bas relay switch to the center high mounted stop lamp (CHMSL), and to the turn signal/hazard flasher module through the stop lamp switch signal circuit. The ground for the CHMSL is applied from G402. The turn signal/hazard flasher module then supplies voltage to the left and right stop lamps in the tail lamp assemblies that have ground at G401 and G402. For export vehicles the stop lamps receive battery positive voltage directly from the bass relay.

There could be a code stored in the EBCM - electronic brake control module - DTC B3903 Stop Lamp Relay Circuit
DTC C0278 Brake Pedal Position Sensor Not Calibrated
there are several other codes that pertane to the brake lights . you could try Replaceing the bas relay !
Fuse Block - Left Rear
In the passenger compartment, under the left side of the rear seat at carpet.

Jun 28, 2015 | 2007 Cadillac CTS 3.6L

1 Answer

How to replace a brake pedal position sensor in a 2007 chevy suburban 1500?


Unplug the sensor, unclip or unscrew the sensor and replace in the same way it came out.

Jun 01, 2014 | Chevrolet Suburban Cars & Trucks

1 Answer

HOW TO REPLACE BRAKE LIGHT SWITCH 2007 TAHOE


It is directly above the brake pedal. It is called a Brake Pedal Postion sensor.

Nov 12, 2012 | 2007 Chevrolet Tahoe

1 Answer

Where is the brake pedal position sensor in a pontiac g6


2007 G6 pontiac brake pedal position sensor location?

Oct 15, 2012 | 2006 Pontiac G6

2 Answers

Reduced engine power, service traction control, service stabilitrak


First of all a scan tool is need for this not a code reader, you need to view scan data after you find what code is stored in the PCM. It could have a problem with the powertrain control module, wiring, or the Accelerator Pedal Position (APP) Sensors. Here are a few codes that could set .
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit

DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit

DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage

DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage

DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

Oct 02, 2012 | 2008 Chevrolet Tahoe LS

1 Answer

I have A6 2L Tdi S Line 2007, my glow plug light flashing and at the same time I can not take my key out , Please help


Check & replace if necessary the brake pedal switch placed above pedals on the support.
If the problem still occurs you might access the ESP & ABS ECU (Electronic Control Unit) using diagnostic equipment connected to the data link connector of the car, in order to pull out all DTC (Diagnostic Trouble Codes) memored.
Then you will be able to replace bad piece(s) and fix the problem by erasing all DTC stocked inside ESP & ABS ECU & reset it.
I'm convinced that your brake pedal switch is faulty because the glow plug warning light went ON, flashing and you can not take your ignition key out. Just replace the brake pedal switch, see if rear stop lamps light when press the brake pedal, and test the car on the road.

Two sensors are provided for engine starting authorization: The first one is placed on the automatic gearbox shift selector electronic module, which send a signal to the ignition switch barrel only if the shift knob is placed in park - "P" position, or in neutral - "N" position. Only now you can take out the ignition key from the ignition switch barrel. The second one is the brake pedal switch placed above brake pedal in the pedals bracket, which send a signal to the ignition switch barrel only if the brake pedal is depressed. Only now it is possible to cranking the engine by the electrical starter motor.

May 19, 2011 | 2008 Audi A6

2 Answers

I have these codes coming up on my 2005 Dodge Ram. 5.7 liter motor: P0406 P2096 P0137 P2299 Thank you.


code #0406 = egr position sensor circuit high ( stuck egr valve or bad egr sensor most likely sensor )

code #2096 = downstream fuel trim system lean ( see next code )

code #0137 = O2 sensor bank 1 sensor 2 circuit low ( replace rear O2 sensor driver side )

code #2299 = brake peddle position/accelerator pedal position incompatible. ( hav you been power braking this truck? ) ( brake light was on wile accelerator was being pushed )

Mar 17, 2011 | 2005 Dodge Ram

1 Answer

2007 pontiac g6 tale lights won't go off while driving. When brakes are applied the lights go off.


shot in the dark here...

possible a reversed harness connector at the brake pedal position sensor (on the brake pedal)... Also, there is a recall for this type of thing too.

Nov 06, 2010 | 2006 Pontiac G6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,060 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...