Question about 2002 Chevrolet Monte Carlo

Open Question

How to remove belt tensioner 2002 monte carlo 3.8

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 68 Answers

SOURCE: The low coolant light stays on in my 2002 monte carlo

Ur coolant level sensor might need changing. If not, the circuit associated with the coolant level sensor needs to be inspected

Posted on Jan 27, 2009

  • 19396 Answers

SOURCE: 2002 monte carlo ss

The fuel filter is located in the pressure line that runs from the fuel tank to the engine, near to the fuel tank.
Keep the engine off for few hours before replacing the filter, to get rid of some pressure in the lines.

Posted on Feb 27, 2009

  • 135 Answers

SOURCE: 2000 monte carlo how to replace water pump.last bolt

there should be holes in power steering pump pulley that when positioned correctly the bole should go through one of those holes, if not then you have to remove the pump

Posted on Apr 29, 2009

  • 401 Answers

SOURCE: my 2002 monte carlo`s fuel gauge fluctuates from full to empty

Hi you need a fuel level sensor

Posted on May 13, 2009

  • 141 Answers

SOURCE: remove the power steering pump pulley on a 2003 monte carlo

you can either remove the steering pump to gain access,if there is no holes in PS pump pulley,you can rent a pulley puller....can be a ***** to get in and use them though....I will drill a hole in it for next time whenever I replace a pump on cars without ....

Posted on Aug 09, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replace belt tensioner on a 2006 monte carlo ss 5.3
This link may help. This model is a bear to get out and in, as it requires a lot of disassembly. This engine was only put in this car a few years. I have taken the front tire off and removed the inner fender and access to some degree that way. I would pay someone to do this cause from what I recall its tough

Jan 09, 2015 | Cars & Trucks

1 Answer

How do I replace the radiator on a 2001 Chevrolet Monte Carlo

1. Empty the radiator
2. disconnect top and lower hoses on the radiator.
3. remove plastic cowling, (should be an upper and lower half with two bolts on each side. There may be an upper plastic cowling as well that will have to be removed.
4. sometimes you can work around the fan, if not remove the fan belt and fan. Make a drawing of how the serpentine belt goes on if it has a serpentine belt. There should be a tension wheel on the belt used for removal and installation of the belt. Be very carefull of your fingers when removing and installing the belt.
5. Remove the four or six bolts that hold the radiator on and lift the radiator out. It may be easier with two people to lift the radiator out.

Nov 22, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

I dont know how to tension the fan belt on my 2003 monte carlo .I need directions or a diagram

the belt on your car is automatically tensioned bu a self adjusting automatic tensioner....if there is slack in the belt either the belt is shot, or the tensioner is bad...try a new belt first.

Btw, I’m available to help over the phone in case u need at

Aug 08, 2010 | 2003 Chevrolet Monte Carlo

3 Answers

How to tighten serpentine belt for 2003 Monte Carlo 3.8L

the belt is self adjusted by a spring loaded automatic belt tensioner, if the belt is noisy or seems loose either the belt size is wrong (if it was replaced recently) or the tensioner is defective or one of the belt idler pulleys is defective.

May 27, 2010 | 2003 Chevrolet Monte Carlo

1 Answer

What is the big pulley call.That control the belt.I have 2002 6cy chevy monte carlo.A it make noise and hard to turn

It's the pulley for the crankshaft. This pulley is very hard to turn, that's the way it should be. It may be noise coming from the tension pulley or another place other than there.

Jan 05, 2010 | 2002 Chevrolet Monte Carlo

1 Answer

How do you replace power steering belts?

Nice ride!! An oldie, but goodie. Should be easy to change the power steering belt on this one. Just loosen the mounting bolt and the adjusting bolt and push the pump toward the engine. That will loosen tension and allow you to remove the belt. Put the new belt on and move the pump out away from engine. You may have use something as a lever to help put the proper tension on, and while holding tension, tighten the mounting and adjustment bolts down. Proper tension is 1/4" deflection at the midway point on the belt. Hope this helped and best wishes.

Jul 30, 2009 | 1983 Chevrolet Monte Carlo

2 Answers

Serpentine belt tension release

on the idler there is either a bolt or a square hole. if it has the square hole it is for a 3/8 drive breaker bar if it just has the bolt on it find a wrench that fits turn either of them right as if you were tightening them this will release your tension.

May 20, 2009 | 1996 Chevrolet Monte Carlo

1 Answer

Replace belt on 2002 Chevrolet Monte Carlo SS

Which belt? AutoZone has an online manual here for your model.

Mar 06, 2009 | 2002 Chevrolet Monte Carlo

Not finding what you are looking for?
2002 Chevrolet Monte Carlo Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides