Question about 1987 Ford F 150

1 Answer

I need a Wiring Schematic for ignition

Ignition may be the problem that has burned up 2 starters, 1 cellunoid and melted battery cables

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,674 Answers

See right side, scroll down to wiring diagrams, somewhere in there you may find what your looking for. If you click on diagrams they will get bigger.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801cd7b5

Posted on Feb 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Do you have a wiring schematic for the starting system on a 1994 Ford 4630 Diesel Tractor?


Randy, Check the attached link and scroll through it, hope it has the info. you need.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

1994 Ford 4630 Diesel Tractor wiring schematic for the starting system...

Apr 22, 2016 | Ford Cars & Trucks

1 Answer

1998 S70 Volvo had to jump started it. And put


In this situation I would check the starter motor solenoid, you are lucky the ECU did not fry cause it would cost more than the car is worth. Starter motor is not that expensive, also check all main relays and fuses. Check the wiring as well. If all fine the ignition coil and ignition barrell would be last. If it is possible plug a computer and run diagnostics too.

Sep 13, 2014 | Cars & Trucks

1 Answer

Turn key to start and nothing happens. All lights are on, battery good. Doesn't turn over---nothing. Switch or starter or some kind of relay??? HELP!!!


For 1999 Buick LeSabre - but you took #1 off the list, so here's the whole "failure to start" list:

Priority Action Part Type Cause
1 Inspect Battery Battery Discharged or Faulty.
2 Inspect Battery Cable Corroded, Broken, Shorted or Poorly Connected Battery Cable.
3 Inspect Distributor Cap Distributor Cap Cracked or Burned.
3 Inspect Fuel Filter Clogged or Dirty Fuel Filter.
5 Inspect Ignition Coil Faulty Ignition Coil.
6 Inspect Wireset Worn, Damaged or Faulty Spark Plug Wire(s).
7 Inspect Spark Plug Incorrectly Gapped or Fouled Spark Plug(s).
8 Inspect Starter Starter Motor Faulty.
9 Inspect Fuel Pump Low Fuel Pressure.
10 Inspect Starter Relay Faulty Starter Starter Relay
11 Inspect Fuel Pump Relay Faulty Fuel Pump Relay.
12 Inspect Fuel Injector Pressure Regulator Faulty Fuel Injector Pressure Regulator.
13 Inspect Ignition Switch Improperly Connected or Faulty Ignition Switch.
14 Inspect Starter Motor Faulty Starter Motor
15 Inspect Fuel Injector Dirty or Worn Fuel Injectors.
16 Inspect Fuel Pump Strainer Clogged or Dirty Fuel Pump Strainer
17 Inspect Engine Control Computer Incorrect Operating Information Being Delivered and Sent From The EEC.
18 Inspect Fuel Tank Fuel Tank Empty.
19 Inspect Carburetor Carburetor Flooded or Faulty Choke.
20 Inspect Distributor Rotor Distributor Rotor broken, burned contacts, or loose
21 Inspect Distributor Worn, Loose, or Incorrectly Installed Distributor.

Sep 12, 2011 | 1999 Buick LeSabre

1 Answer

1997 Lexus SC300. 113,000 miles. Starter stays engaged and keeps cranking motor with ignition off and key out of ignition. Had to pull battery cable to disengage starter. When battery cable is reattached...


You most likely have a short in the wiring to the starter.

Last time I saw something like that a vehicle's exhaust headers created heat which eventually melted the wire's insulation and several of the wires were exposed and shorting on each other and the ground of the vehicle. If possible, get the car on a lift and inspect your starters wiring....

Hope this helps...

Jun 17, 2011 | Lexus SC 300 Cars & Trucks

1 Answer

My car wont start


1 Inspect Battery -- Battery Discharged or Faulty.
2 Inspect Battery Cable -- Corroded, Broken, Shorted or Poorly Connected Battery Cable.
3 Inspect Distributor Cap -- Distributor Cap Cracked or Burned.
3 Inspect Fuel Filter -- Clogged or Dirty Fuel Filter.
5 Inspect Coil - Ignition -- Faulty Ignition Coil.
6 Inspect Wireset -- Worn, Damaged or Faulty Spark Plug Wire(s).
7 Inspect Spark Plug -- Incorrectly Gapped or Fouled Spark Plug(s).
8 Inspect Starter -- Starter Motor Faulty.
9 Inspect Fuel Pump -- Low Fuel Pressure.
10 Inspect Solenoid Switch -- Faulty Starter Solenoid Switch.
11 Inspect Relay - Fuel Pump ----- Faulty Fuel Pump Relay.
12 Inspect Fuel Injector Pressure Regulator --- Faulty Fuel Injector Pressure Regulator.
13 Inspect Ignition Switch --- Improperly Connected or Faulty Ignition Switch.
14 Inspect Starter Drive --- Faulty Starter Drive.
15 Inspect Fuel Injector --- Dirty or Worn Fuel Injectors.
16 Inspect Fuel Pump Strainer ---- Clogged or Dirty Fuel Pump Strainerat.

Mar 17, 2011 | 1995 Buick LeSabre

1 Answer

How to replace the starter


Toyota Celica, Corolla, ECHO & MR2 1999-05
Starter - Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Radiator upper support seal
Air cleaner
Engine under covers
Starter wiring
Starter

3. Installation is the reverse of removal. Torque the bolts to 28 ft. lbs. (37 Nm). Note that the bolts are 2 different lengths.


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Battery and tray. On models equipped with an air bag, work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery.
Coolant reservoir
Reservoir hose from the radiator
Right side under cover
Wiring clamp
Wiring from the starter
Starter


To install:
1. Install or connect the following:
Starter
Starter wiring and nut
Starter connector and wire clamp
Right side engine cover
Radiator reservoir and hose
Battery and tray

2. Check the cooling system and top off if necessary.


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Negative battery cable. On models equipped with an air bag, work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery
Engine under covers
Wiring from the starter terminals
Starter mounting bolts
Starter


To install:
1. Install or connect the following:
Starter
Starter wiring
Engine under covers


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Negative battery cable
Front engine undercover
Starter wiring harness connectors
Starter mounting bolts
Starter motor


To install:
1. Install or connect the following:
Starter motor. Tighten the bolts to 28 ft. lbs. (37 Nm).
Starter wiring harness connectors
Front engine undercover
Negative battery cable

Hope help with this (remember rated and comment).

Mar 11, 2010 | 2003 Toyota Corolla

3 Answers

I go to start the car and it won't start have to play around with ignition and then it will start, has nothing to do with the battery. Does this mean that I need a whole new starter or is it just the...


When you say you have to mess around with the ignition, are you saying it clicks while you are turning the key to the starting position until it takes off? If so, you would need to replace the starter because you have a dead spot in the electrical windings most likely. It could be a solenoid, but I am guessing the starter is your problem if I am guessing correctly on what you mean by messing around with the ignition.

Good Luck

Dec 15, 2009 | 1995 Geo Prizm

1 Answer

Rebuilt chevy 454 engine, now need distributor and


just put a new starter in my 1993 chevy 454 and now i'm not getting fire, the old starter solenoid was sticking and melted the neg battery cable. I'm wondering if that also burned something else out?

Oct 27, 2009 | 1993 Chevrolet C/K 3500

1 Answer

I have a 90 Ford Taurus SW 3.0L I am getting No Power from ignition nor power inside the car. What is going on. We replaced the ignition solenoid and notice that a fusible link line was melted that goes...


YES THE FUSE LINK THAT MELTED CAUSE NO POWER TO IGNITION.NO POWER INSIDE CAR ALSO MEANS DEAD BATTERY.REPLACE FUSE LINK.BUT FIRST REMOVE THE STARTER HAVE IT TESTED AT ADVANCE AUTO A BAD STARTER CAN CAUSE FUSE LINK TO BURN OUT.

Aug 02, 2009 | 1990 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...