Question about 2001 Dodge Ram 3500 Truck

Open Question

What is cluster B fuse for in a 2001 Dodge ram

Draw on the battery till I remove cluster B from fuse panel...what does that fuse control?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 85 Answers

SOURCE: Door Panel Removal -2001 Dodge Caravan

to be honest about it I always pry it out enough to get my fingers behind it to get a grip and **** as hard as i can to get it loose i believe the 2001 has the two piece clips that are tough to get to let go and the clips usually break very rarely the panel will id say like 1 in 75 and there are so many clips you cant tell if one is missing

Posted on Jul 18, 2008

Ad
goofduck
  • 490 Answers

SOURCE: 2001 Dodge Ram 1500; how to reset computer after replacing dead battery

disconnect the positive battery cable for 2 minutes and that will reset the computer

Posted on Apr 13, 2009

MNfisherman
  • 11896 Answers

SOURCE: I have a 2001 dodge ram 3500 cummings. When I the

The accumulator may not be holding pressure or else the cruise control switch may having a fault effecting the cruise control circuit.
Check all the vacuum lines on the accumulator and the reset of the system.

Posted on Jul 16, 2009

  • 138 Answers

SOURCE: 2001 Dodge Ram, 3500, CTD 5.9, AT, 2WD, No Bus

No bus error code has nothing to do with your fuse panel this is a ECM /ECU error code... sorry but get ready to spend some money for a new ECM

Posted on Sep 13, 2009

  • 83 Answers

SOURCE: Need to replace instrument cluster/AC bulbs

Hello, You can obtain a 2004 Ram Factory Service Manual with all of that information available from Promanuals.net. The reason why it may be so important is because right before the removal instructions the service manual has diagnostic instructions to try. There are numerous pages on removing the instrument cluster, and cluster bezel.

(1) Disconnect and isolate the battery negative
cable. (For Airbag)

(2) Remove the cluster bezel from the instrument
panel. (Refer to 23 - BODY/INSTRUMENT PANEL/
CLUSTER BEZEL - REMOVAL).

(3) Remove the four screws that secure the instrument
cluster to the instrument panel structural support
(Fig. 5).

(4) Pull the instrument cluster rearward far
enough to access and disconnect the instrument
panel wire harness connectors for the cluster from
the connector receptacles on the back of the cluster
housing.

(5) Remove the instrument cluster from the instrument
panel.
9e8a042.jpg

Posted on Oct 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would make the battery go dead sitting 2 days without being cranked


Connected ? Could be a light or fault on alternator draining.if it loses charge disconnected battery is finished

Oct 01, 2015 | 2005 Jeep Grand Cherokee

1 Answer

Location of flasher unit 2001 dodge pu 2500 ram


A defective turn signal relay in the Ram 2500 can cause your signals to malfunction or stop working entirely. As a relay ages, so does its circuitry. However, the most common cause of relay damage is attributable to an electrical fault in a relative location, such as the taillight assembly. You can find and replace the turn signal relay in your Dodge Ram 2500 with a few common tools. You can do this job at home; it should take you less than 20 minutes to do.

Things You'll Need :

Phillips screwdriver

Socket wrench set


Instructions:

1. Open the driver's door on your Ram 2500. Reach beneath the front of the driver's seat and pull the seat release lever up. Push the seat toward the rear of the truck as far as it will go.

2. Kneel within the door opening so that you're able to see the bottom of the steering wheel. Below the base of the steering wheel you should see a large square piece of trim panel. This is your Ram 2500's knee-blocker panel.

3. Remove the screw on the top, left and right of the panel with a Phillips screwdriver. Along the bottom lip of the panel--horizontally--you should see three more screws. Remove the screws with your Phillips screwdriver.

4. Take the panel off to reveal your interior relay and fuse cluster. If your turn signal relay has never been replaced, it should be the only white relay in the cluster. If it was replaced before with an aftermarket relay, it will likely be black in color. The square turn signal relay sits on the top, outer right corner of the relay and fuse cluster. It pulls out of place and simply plugs back into position.

I hope this helps.

Apr 30, 2015 | Dodge Cars & Trucks

1 Answer

What fuse controls gauges on 2001 dodge ram


pull your fuse panel off and the fuses and what they are for should be on back of the panel you pull.

Feb 01, 2015 | 2001 Dodge Ram 1500 Truck 2WD

2 Answers

2002 Dodge Caravan... why new battery keeps draining charge...


You have a wiring problem. .it's creating a draw on the battery. .you pull each fuse till draw goes away and your short is in that circuit. .

May 27, 2014 | 2002 Dodge Caravan

1 Answer

1998 dodge ram 1500 dash lights wont work


Walker Muffler - Aluminized Steel Direct OE Replacement 1998-2001 Dodge Ram 1500.-------------------------------------------------------------------------------------
SLIM HID XENON light

Jan 10, 2013 | 1998 Dodge Ram 1500 4WD

1 Answer

Hello, Im a US Marine and dont know alot about automotive but Im not completly numb... My father in-laws 2003 4x4 dodge pick has been blowing fuse #18 which when blown or removed the dash lights go out......


That fuse also supplies illumination to the radio, hvac controller, cup holder and cigarette tray. I think the best thing to do is start unplugging each one of these until the fuse stops blowing. Then plug the last think in that you unplugged to make sure that makes the fuse blow. If you suspect the instrument cluster start with that first.

Sep 28, 2010 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

I have a 2001 Dodge Ram 3500 4X4, w/5 spd tranny. I am having trouble with my HVAC controls (they quit working and only hot air comes out), and also the instrument cluster. Periodically I lose the tach...


tach is most likely a cam sensor, hvac could be a bad vacuum problem (bad hose ) the electrical (dash stuff) I would start looking for a loose or bad ground wire or dirty battery terminals

Sep 04, 2010 | 2001 Dodge Ram Maxi

1 Answer

Something is killing the battery, have changed alternator but still have same problem


Why change the alt? Put an amp meter in the battery circuit. Remove a battery cable and put the meter in series. Then pull one fuse at at time till you find the battery drain. Keep in mind the clock and computer will draw up to 30 millamps all the time. Also get to know if you have anything that is supposed to time out when ignition is off.

Oct 16, 2009 | 1991 Dodge Ram 350

1 Answer

Need to replace instrument cluster/AC bulbs


Hello, You can obtain a 2004 Ram Factory Service Manual with all of that information available from Promanuals.net. The reason why it may be so important is because right before the removal instructions the service manual has diagnostic instructions to try. There are numerous pages on removing the instrument cluster, and cluster bezel.

(1) Disconnect and isolate the battery negative
cable. (For Airbag)

(2) Remove the cluster bezel from the instrument
panel. (Refer to 23 - BODY/INSTRUMENT PANEL/
CLUSTER BEZEL - REMOVAL).

(3) Remove the four screws that secure the instrument
cluster to the instrument panel structural support
(Fig. 5).

(4) Pull the instrument cluster rearward far
enough to access and disconnect the instrument
panel wire harness connectors for the cluster from
the connector receptacles on the back of the cluster
housing.

(5) Remove the instrument cluster from the instrument
panel.
9e8a042.jpg

Oct 01, 2009 | 2004 Dodge Ram 1500

1 Answer

Cruise Control


in the fuse panel right up under the instrumental panel.

Jun 02, 2008 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...