Question about Cars & Trucks

Open Question

How do I replace CV Bearings on a VW Microbus 2.5?

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

TDISLine
  • 1874 Answers

SOURCE: how to check if vw 1996 microbus radiator is

You must remove the bottom rubber hose from the radiator, and also the upper hose. Extract the radiator out or simply flush the radiator in reverse direction of water flow. If the radiator is clogged you can try to clean inside (chemically) or replace it. Flush the cooling system in reverse direction of water flow. Refit all in reverse order and after that purge air out of cooling system.

Posted on Dec 05, 2009

stumann2
  • 193 Answers

SOURCE: replacing a 2004 VW Beetle inner CV boot

Replace the whole axle. You can get rebuilt axles for around $50. Then you have everything new.

Posted on Feb 24, 2010

johnjohn2
  • 5763 Answers

SOURCE: VW Microbus 2.3I Transmission problems

You can try to adjust the clutch cable if it has a cable, if its hydrualyic clutch then i would say theres a problem with the clutch plate or preasure plate, but first check the fluid level in the clutch master cylinder if its low then you may have a leak, most of the time its the slave cylinder or master that leak, the master is what the clutch pedal pushes which inturn send fluid to the slave cylinder at the trany which pushes the cltuch fork,so start by seeing if its hydraulic which i think it is. then fluid check if low check for leaks.

Posted on Jul 15, 2010

johnjohn2
  • 5763 Answers

SOURCE: i want to change timing belt for microbus 2.6 but i am not shore about the mark on the cam

We do not have micro bus here, but i can tell you that a timing component kit comes with a small book with marks and some directions, another way is to line engine up at top dead center and mark gears before removal, Note; all gears must be line up correctly or engine damage will occur. after you install the timing belt spin crank pulley 2 revolutions and all marks should line back up, if not then realign,

Posted on Sep 30, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

VW microbus 2.3 i rad fan relay were will i find it or the fuse and how would identify it


I don't know that microbus very well, but often there is a fuse box either in the engine compartment that contains fuses and relays, or inside under the driver's dash panel. Otherwise my best friend is Google on these questions. Peace.

Nov 04, 2014 | Cars & Trucks

1 Answer

2.6i engine torque settings, for vw microbus


Visit the on-line store, know as reliable-store, they have the parts manuals. I'm sure you will get the solution of your problem
Best Manuals

Oct 20, 2014 | Cars & Trucks

3 Answers

I need to kno the cylender head torque specs for a 2.3i vw microbus five cylender


The Audi 5 cylinder engine (Engine code AFU) was mainly produced in South Africa and was called a Microbus. The engine capacity was 2309cc. The Microbus 2.3i T3 was produced from 1992-2002.

According to Mead & McGrouther - Data Digest the torque settings for the cylinder head bolts are as follows: 40Nm + 60Nm + 90'degree turn + 90' degree turn. The cylinder head bolts has to be replaced with brand new ones.

The Main Bearings: 65Nm. The Big Ends: 30Nm + 90 degree turn.

The OHC Bearing Caps: 20Nm.

Flywheel Bolts Manual transmission: 60Nm + 90 degree turn.

Jul 28, 2014 | Cars & Trucks

1 Answer

Flasher relay location on vw microbus 1995 model


Flasher relay Location on microbus 2,5

Nov 26, 2013 | Cars & Trucks

1 Answer

I want to change timing belt for microbus 2.6 but i am not shore about the mark on the cam


We do not have micro bus here, but i can tell you that a timing component kit comes with a small book with marks and some directions, another way is to line engine up at top dead center and mark gears before removal, Note; all gears must be line up correctly or engine damage will occur. after you install the timing belt spin crank pulley 2 revolutions and all marks should line back up, if not then realign,

Sep 30, 2012 | Cars & Trucks

1 Answer

How to check if vw 1996 microbus radiator is


You must remove the bottom rubber hose from the radiator, and also the upper hose. Extract the radiator out or simply flush the radiator in reverse direction of water flow. If the radiator is clogged you can try to clean inside (chemically) or replace it. Flush the cooling system in reverse direction of water flow. Refit all in reverse order and after that purge air out of cooling system.

Dec 05, 2009 | 2005 Volkswagen Microbus

2 Answers

Vw 2.6 immobiliser


My vw caravelle bus 2.6i -1996 model cant start- just cranking but not firing, cant hear the pump click as usual. It was just running fine, then switched off, when i got back all these started. kindly assist.

Dec 04, 2008 | 2005 Volkswagen Microbus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...