Question about Ford F-150
And all the lights come on
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: ford f-150 ignition switch
You will need to take the houseing off around the ignition should only be a couple of screws. Then here comes the fun bit, You will have to see if you can get hold of the tool that undoes and does up the bolts (as I will call them for you not there proper name but tech name may have you going the what ) that hold the ignition on or if not fussy you could just drill them out lift the ignition off after unlocking the steering lock so turn onto first click so radio would normally come on and with the new one you can always just change the bolts that may or maynot come with it( and most times they don't) with hex head ones or what ever is your fancy, but remember if you put it on with a spanner a thief can undo it with one, install just a reverse on uninstall. then you just screw the houseing back on. You maybe able to find or may know someone with ability to get the tool for the original bolts or if handy with a grinder and have a piece of metal around you could try making one. Most are a sort of rounded out triangle, but they usually only do up easily and are very hard to undo without the proper tool and most mechanics will just replace them with new ones as the reverse direction is rounded up to the back side to make it very difficult for a thief to simply undo in a few minutes, I've known people who have used a flat screw driver and smashed a groove into them to undo but remember that will also make them easy for a thief to just remove and bypass your ignition system ie steering locks and soforth
Posted on Jul 26, 2008
Let's hope with a Supercab you have a tilt steering wheel.If so, just unhook the negative battery cable, line your wheels up straight, leave it in park, and turn the key on. On the underside of the housing the key and lock cylinder is in, above the hazard switch, is a very small hole with a locking pin inside. Using a small punch, or whatever works for you, simply push the pin in as you pull the lock cylinder out, sort of twisting and rotating the cylinder as you pull. A non-tilting column is a little harder, but it's not difficult, just take your time and think about what you're doing. First you need to remove the steering wheel, so make sure you mark the wheel and column in a couple places so it's easy to line up later. On the back side of the wheel are two screws that hold the front padding with the horn in it. Remove it, being careful of the wires, and disconnect. With cruise control, when you disconnect the wiring in there, you need to squeeze the ground wire terminal clip carefully but firmly (it's sort of like a "J" clip), and pull the wire out of the hole in the wheel. DON'T just pull it out, squeeze, it's spring loaded. Then remove the switch for the horn and the nut holding the wheel on. Use a puller on the steering wheel, but not one they call a "knock off", because it's pretty easy to screw things up if you go hammerin' on the wheel or the column shaft. Take your time. Then you'll find the little hole with the retaining pin near the base of the lock cylinder inside the column, remove it the same way. Remember, in park with key on. Hope this helps you out. If you happen to be referring to the actual "ignition switch", located inside the steering column (which most people don't even know actually exists), or you don't have the key and that's why you're doing this, you'll have to let me know, and I'll try to walk you through those procedures at a later date.
Posted on Aug 26, 2008
engine should not continue to turn over when key is out sounds like the key switch the wrong one or you have wired it wrong
Posted on Mar 07, 2010
Tips for a great answer:
Feb 26, 2015 | 1988 Ford F 150
Feb 26, 2015 | 1988 Ford F 150
Oct 31, 2010 | 1989 Ford F 150
Apr 17, 2010 | 1984 Ford F 150
Mar 07, 2010 | 1988 Ford F 150
Oct 22, 2009 | 1987 Ford F 150
Apr 14, 2009 | 2004 Ford F150
47 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: