Question about 2007 Chrysler Sebring Sedan

Open Question

P2006 check engine light on - 2007 Chrysler Sebring Sedan

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

3.2l. What are the probable causes of DTCs P2006 and P2007?

code p 2006 refers to intake manifold air control actuator , bank 1 --actuator stuck closed or for 2007 , the intake air manifold control actuator bank 1--solenoid stuck closed === causes ---wiring --- intake manifold air control actuator / solenoid ---mechanical fault
so for both it is either the actuator or the solenoid that is showing the codes

Nov 06, 2015 | 2007 Audi A4 Convertible

1 Answer

Code p2006 and p2007 check engine light on computer diagnostic says Bank1 and bank 2 closed manifold is this an easy fix or what are my options

It could be an easy fix ,what make ,model an year vehicle . I know I saw a video on you tube on this very thing , the vehicle was a ford an it had a vacuum hose leak . Plus there was another one that had plastic pieces that broke an the control rod fell out of control arm. Check out some of these you tube videos . Installing New IMRC Bushing Ford Duratec Engine

Nov 06, 2015 | Cars & Trucks

1 Answer

Why my mercedes 2006 e350 will not start with code P2006?

P2006 is a Knock Sensor Code. What Octane Rated Gas are you using? Try Premium Grade Gasoline if you are not already doing so.
Hope this helps

Aug 26, 2014 | Mercedes-Benz E350 Cars & Trucks

1 Answer


read that page in the FSM. on P2006,
and do what it says.
same answer for all cars,
it tell you what tests to do to find the cause.
try , log in and read what it says;.

the PCM can set that for 2 reasons.
1: the IRMC is bad.
2: the vacuum reading on the engine or so out of wack. this test lies.

this might be under the 8year, smog warranty, did you check?
what it does is , give better low end torque. so, its no show stopper.
in a real jeep shop, the attach their scan tool and tell it to cycle the
IMRC solenoid, and if it moves, then it must be some other cause.
if it dont move, they fix that. (wires bad, or solenoid)

one thing people dont understand is that most cheap scan tools
(like used in most autozoned) do not let you see all OBD2 DTC codes
there are many, codes, it seems yours is scanning right.
P2. is a factory only code.
so got other codes thrown?
or other symptoms, like bogging or misfire, or??????

also nobody can tell you what you can do.
we dont know your skills or tools ? or many other facts.
this code means the feed back signal says it didnt move, or did not move fully.
that is why not having factory tool makes this hard.
check connections, test the MFV. by hand. test the solenoid by hand.
if all these check out, then we scan the system looking for all other sensors reading funny.

here is the FSM page .

Intake Manifold Runner Control Stuck Closed
Number of Trips to Set Code: 1
Trouble Code Conditions:
The Powertrain Control Module (PCM) detects that the position feedback of the Manifold Flow Valve Position Sensor is not within range of the adapted value learned during in-plant initialization or after a non volatile memory reset (adaptive memory clear).
Possible Causes:
  • * 5 volt supply circuit open or high resistance, shorted to voltage, ground or another circuit
  • * MFV signal circuit open or high resistance, shorted to voltage, ground or another circuit
  • * Sensor ground circuit open or high resistance
  • * Manifold flow valve
  • * Intake manifold
  • * PCM

Mar 24, 2014 | 2011 Jeep Patriot

1 Answer

2004 mercury montery imrc problem snap on computer gives p2006 code need help in trobleshooting

If you don't understand how to diagnose the imrc ,
have a shop do it

You can Google any codes

The intake runner is stuck closed,if you go by the code

I go by what I see & test things, before any parts get replaced

Feb 08, 2013 | 2004 Mercury Montery

1 Answer


here is what this code means keep in mind that this only give you a idea on what it may be and a staring point but it may also fix your issue

P2006 = intake manifold runner control stuck closed bank 1

Jan 24, 2013 | 2011 Hyundai Santa Fe

1 Answer

My check engine on my 2006 Audi a6 came on the codes that came up at Midas are P2006 and p2007 what are my problems??

The code reader I have gives me the description to the code being displayed and as you said Midas checked it, they should have given you a description also.

Jan 05, 2012 | 2006 Audi A6

2 Answers

Dodge caliber P2006 check engine light

P2006-intake Manifold Runner Control Stuck Closed

Hope that helps.

Sep 08, 2011 | Dodge Caliber Cars & Trucks

Not finding what you are looking for?
2007 Chrysler Sebring Sedan Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides