Question about Cars & Trucks

Open Question

Vw passat 2006 timing chain marks diragrahm - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

johnny5846
  • 379 Answers

SOURCE: VW Passat 2006 service now

2 options depending on your displays .

Press and hold the service wrench button with the ignition off. While still holding the button, turn your ignition to "on" (but don't start the car). Press the Min clock button and then release the wrench button.


With key off press and hold the 0.0 button on the cluster. With your other hand turn the key to the on position , while still holding 0.0 button, press the minute button for 1 second and you will see the service reset.

cheers

Posted on Jan 10, 2009

  • 548 Answers

SOURCE: vw passat 2006 repair manual

try here first

http://www.pdf-word.net/automotive-guide-volkswagen/volkswagen-passat-technical-bulletin.html


your local library than your auto parts store or book store

Posted on Sep 01, 2009

  • 4102 Answers

SOURCE: I am having troubles locating

hi, here is a guide i have come across on this site written by another expert it should be the one for your engine but always double check.

If you are unsure what you are doing then please go out and buy a haines workshop manual as these tell you every detail you need to know so that would be your best solution.

Please dont do this work if your unsure what you are doing as you could damage the engine beyond repair so you have been warned;

it covers single cam and if you scroll down it shows double cam ok

Sep 14, 2009 - VW Passat & Audi A4 1990-2000 Repair Guide
Timing Belt - REMOVAL & INSTALLATION

2.8L SOHC (AFC) V6 Engine

  1. Note the radio security code and disconnect the negative battery cable.
  2. Place the (hood) lock carrier in the service position. For additional information, please refer to the following topic(s): Body And Trim, Service Position, Front Bumper, Hood Lock Carrier.
  3. Remove the engine accessory drive belt. For additional information, please refer to the following topic(s): General Information And Maintenance, Routing Maintenance And Tune-up.
  4. Turn the engine by hand to Top Dead Center (TDC) on the firing stroke for cylinder No. 1.
NOTE The large holes in the camshaft sprocket lock plates should be on the inside facing one another.
  1. Remove the Crankshaft Position (CKP) sensor from the lower left side of the engine block. Make sure the engine is at TDC and install the threaded crankshaft holding pin Tool No. 3242 and lightly tighten.
  2. Remove the upper timing belt covers, the crankshaft vibration damper and then the lower timing belt cover.
  3. Loosen the camshaft sprocket bolts slightly and use a suitable pulley to release the sprockets from the tapered ends of the camshafts.
  4. Loosen the tensioner roller and remove the drive belt.
To install :
  1. Install the timing belt over the sprockets, then the idler rollers and lastly over the tensioner.
  2. Install camshaft alignment tool holder Tool No. 3243 into the camshaft alignment flanges.
  3. Check and adjust the cam belt tension such that the upper left portion of the belt between the tensioner and the left cam gear can just be twisted 90° ( 1 / 4 turn).
  4. Tighten the cam belt tensioning roller to 33 ft. lbs. (45 Nm), and the camshaft sprocket bolts.
  5. The balance of the installation is in reverse order of removal.

2.8L DOHC 5V (AHA) V6 Engine
  1. Note the radio security code and disconnect the negative battery cable.
  2. Place the (hood) lock carrier in the service position. For additional information, please refer to the following topic(s): Body And Trim, Service Position, Front Bumper, Hood Lock Carrier.
  3. Remove the engine accessory drive belt. For additional information, please refer to the following topic(s): General Information And Maintenance, Routing Maintenance And Tune-up.
  4. Turn the engine by hand to Top Dead Center (TDC) on the firing stroke for cylinder No. 1.
NOTE The large holes in the camshaft sprocket lock plates should be on the inside facing one another.
  1. On the cylinder block near the crankshaft, remove the sealing plug from the lower left side of the engine block. Make sure the engine is at TDC and install the threaded crankshaft holding pin Tool No. 3242 and lightly tighten.
  2. Remove the upper timing belt covers, the crankshaft vibration damper and then the lower timing belt cover.
  3. Loosen the camshaft sprocket bolts slightly and use a suitable pulley to release the sprockets from the tapered ends of the camshafts.
  4. Using a 8mm Allen® wrench, rotate the timing belt tensioner roller clockwise until the tensioner is compressed; then, insert a 2mm spring pin through the tensioner housing and tensioner plunger to secure it in place. When the plunger is secure, release the wrench tension.
  5. Remove the damper-to-crankshaft bolts and the damper.
NOTE It is not necessary to remove the center bolt when removing the crankshaft damper.
  1. Remove the serpentine belt idler and the crankshaft damper guard.
  2. Mark the running direction of the timing belt and remove it from the pulleys.
58637f8.jpg

Fig. Crankshaft pulley alignment location for TDC-Audi 2.8L V6 engines


d58d8c0.jpg

Fig. Left camshaft sprocket alignment position for TDC; right camshaft position is similar-Audi 2.8L V6 engines


934cbaf.jpg

Fig. View of crankshaft holding tool installed-Audi 2.8L V6 engines


9091ff0.jpg

Fig. View of camshaft locator bar installed-Audi 2.8L V6 engines


To install:
  1. Make sure that the camshaft pulleys and the crankshaft pulley are in alignment with TDC of the No. 1 cylinder's compression stroke.
  2. Install the timing belt; make sure the timing belt is installed in the correct running direction from which it was removed.
  3. Using a 8mm Allen® wrench, rotate the timing belt tensioner roller clockwise until the tensioner is compressed; then, remove the 2mm spring pin from the tensioner housing. Slowly, release the tensioner spring pressure to put pressure on the timing belt.
  4. Install the crankshaft damper guard and the serpentine belt idler pulley; torque the idler pulley bolts to 33 ft. lbs. (45 Nm).
  5. Install the crankshaft damper and torque the damper-to-crankshaft bolts to 15 ft. lbs. If the damper-to-crankshaft center bolt was removed, torque it to 147 ft. lbs. (200 Nm) plus 180° 1 / 2 turn).
  6. Remove the Crankshaft Holder tool No. 3242 and install the sealing plug.
  7. Replace the remaining components by reversing the removal procedures.
  8. Refill the cooling system and the automatic transaxle. Connect the electrical connectors. Install the negative battery cable last.
  9. Test drive the vehicle.

Posted on Jan 18, 2010

  • 1 Answer

SOURCE: need 2.0l 4-CYL ALIGNING CAMSHAFT/ TIMING MARKS

2005 vw jetta 2.0l timing marks

Posted on Feb 18, 2010

  • 4793 Answers

SOURCE: i have a 2002 vw

hi mark,to answer your question,if you look at the very front of the engine you will see some pulleys for the waterpump/pwr steering/alt.just behind you will see a 1.1/2 plastic cover that hides the BELT.(engine designed by Hyundai in collaberation with VW for the far eastern market(China)same block also used for 3cyl diesel.
regards,geoff.

Posted on Oct 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the fuse for the rear cigarette lighter on VW Passat?


did you look in the fuse box in the engine compartment ?
and are any of the fuses marked power outlet ?

Jul 28, 2012 | Cars & Trucks

1 Answer

Removing head on 1999 passat 1.8


Timing belt set-up diagram on 1999 VW Passat 1.8

tdisline_517.jpg


tdisline_518.jpg

Timing chain in cylinder head set-up:

tdisline_25.png
tdisline_26.png
Cylinder head instructions:

Tightening sequence

tdisline_519.jpg
Renew bolts!
Stage 1: Tighten = 40 Nm

Stage 2: Tighten = 60 Nm
Stage 3: Tighten = 90 degrees
Stage 4: Tighten = 90 degrees

May 12, 2011 | 1999 Volkswagen Passat

1 Answer

Hhere is lthe locaton of the tink by chek the transmition oil? I dont faund.. in volkswagen passat 2006


1. Check and add transmission fluid on a 2006 VW Passat with manual gearbox:

tdisline_274.jpg
tdisline_275.jpg

2. Check and add transmission fluid on a 2006 VW Passat with automatic gearbox:

tdisline_276.jpg
tdisline_277.jpg

Please do rate my response. Thanks!

Feb 18, 2011 | 2006 Volkswagen Passat

1 Answer

How do you check and add transmition fluid on a 2006 VW Passat


1. Check and add transmission fluid on a 2006 VW Passat with manual gearbox:

670c2a2.jpg
3f1e583.jpg

2. Check and add transmission fluid on a 2006 VW Passat with automatic gearbox:

e6fa3a0.jpg
673dcb1.jpg

Oct 08, 2010 | 2001 Volkswagen Passat

1 Answer

How to set date in passat 2006


The way you change the date on 2006 VW Passat is via the setup screen. Go to setup, scroll down to date & time, and then go to date.

Jun 12, 2010 | 2006 Volkswagen Passat

1 Answer

How can i turn off 2006 VW Passat check engine


lots of different ways try tightening your gas cap

Dec 22, 2009 | 2006 Volkswagen Passat

1 Answer

Third brake light fuse number for 2006 vw passat


There is no fuse for the third brake light that I know of, it is wired into the main brake light wiring on most cars anyway. Probably the bulb is blown.

Nov 10, 2009 | 2006 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...