Question about 2003 Ford Excursion

Open Question

Where is the accessory delay relay located - 2003 Ford Excursion

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of the power window relay in a 1998 cadillac eldorado


http://www.bbbind.com/free_tsb.html free wiring diagrams !
Left Front Power Window Switch
The battery voltage is applied from the WINDOWS circuit breaker through CKT 42 (RED) to the accessory time delay relay. The accessory time delay relay supplies voltage through CKT 70 (PNK) to the left front power window switch under the following conditions:
?€¢
The ignition is in the RUN position.


?€¢
The retained accessory power (RAP) is active.

When an UP switch on the left front power window switch is operated, the battery voltage is applied to the power window motor. The power window motor is grounded through the DOWN contacts of the left front power window switch to G204. The motor runs in order to drive the power window up. When a DOWN switch in the left front power window switch is operated, the battery voltage is applied to the power window motor in the opposite direction. The power window motor is grounded through the UP contacts in the left front power window switch to G204. The motor runs in order to drive the power window down.
Accessory Time Delay Relay
On the left front of the passenger compartment, taped in the body harness

Jun 18, 2016 | 1998 Chevrolet Cavalier

1 Answer

Where is the Power Windows Fuse in a 2005 Ford Taurus?


It is located in the SJB smart junction box , it's a fuse / relay center / microprocessor ! Fuse # F2.10 30 amp . location -behind left side dash panel . Also check the accessory relay . Top relay left side , same location SJB .
Visual Inspection Chart Mechanical Electrical
  • Door window regulator and motor
  • Door glass top run
  • Door window glass
  • Loose, corroded connectors
  • Circuitry
  • Window control switch
  • Battery junction box (BJB) fuse(s):
    • 1 (60A)
    • 3 (60A)
    • 11 (50A)
  • Smart junction box (SJB) fuse(s):
    • 7 (20A)
    • 27 (10A)
    • 30 (10A)
  • SJB circuit breaker 10 (30A)
  • SJB rear window defrost relay 1
  • Relay center box 1 rear window defrost relay 2
  • Delayed accessory relay
  • Battery saver relay
  • Rear window defrost grid

Sep 23, 2015 | 2005 Ford Taurus

1 Answer

Accesery acc delay relay where found on 2006 grand cherekee


The RUN/ACCESSORY DELAY RELAY is located in the junction block.

Oct 14, 2014 | Cars & Trucks

1 Answer

Where are accessory delay relays located on 2002 ford explorers


It is located on the top of the inside fue box in the dash.

Nov 09, 2012 | 2002 Ford Explorer

1 Answer

Accessory delay relay


built into the motor ,its called a confort type motor

Mar 28, 2012 | 2004 Mercury Mountaineer

1 Answer

Cant find fuse for power windows?


According with the Explorer Owner Guide, I suggest...
1. Check for power on the Light Blue/Black (LB/BK) wire at the master window switch.
2. Check for a good ground to the master window switch on the Black (BK) wire. This wire provides the ground circuit for all of the window motors.

If both of these are good you probably have a bad master switch(drivers master switch).

The Light Blue/Black (LB/BK) wire gets its power supply from the accessory delay relay in the Central Junction Box (CJB) located under the instrument panel. The Generic Electronic Module (GEM) controls activation of the accessory delay relay. Fuse 2.17 is a 15 amp fuse in the CJB which supplies power to the relay. Fuse F1.6 is a 60 amp fuse in Battery Junction Box (BJB) which also supplies power to the accessory delay relay. G400(ground) is located at the driver side rear of the vehicle near the tail light assembly. This connection provides a ground for the master window switch (click image for zoom).

zjlimited_780.gif


For additional details, i suggest try to look and obtain this 2002 Explorer Owner Guide 6th Printing (English).

Hope helps.

Oct 12, 2011 | 2002 Ford Explorer

1 Answer

My 4WD dash lights are flashing and the 4WD won't engage. Also, my power windows and moonroof won't work. I've checked all of the fuses and they're good. What else should I check?


There's a TSB out for this concern. Its just a faulty relay

adobe.gif Printable View (8 KB) TSB
98-13-19
  • ELECTRICAL - LOSS OF 4X4 SYSTEM
  • LAMP - 4X4 LAMP ILLUMINATED
  • LAMP - NO INTERIOR LIGHTING
  • MOON ROOF - INTERMITTENT OR LOSS OF POWER
  • REAR WIPER - INTERMITTENT OR LOSS OF POWER
  • WINDOWS - INTERMITTENT OR LOSS OF POWER
Publication Date: JULY 6, 1998
LIGHT TRUCK: 1997-1998 EXPLORER, MOUNTAINEER
This TSB article is being republished in its entirety to correct the Service Procedure Steps. ISSUE: A flashing 4X4 lamp and/or a intermittent or loss of:
  • Power windows
  • Interior lights
  • Rear wiper (if equipped)
  • Moon roof (if equipped)
  • 4x4 system (if equipped)
may occur on some vehicles. This may be caused by an intermittent Battery Saver, Accessory Delay or One-Touch-Down Relay operation and possible chafing of vehicle wire harness.
ACTION: Repair the affected circuit, and/or replace the Battery Saver, Accessory Delay, or One-Touch-Down Relay. Refer to the following Diagnostic/Service Procedure for details before replacing any components.
DIAGNOSTIC/SERVICE PROCEDURE Accurately RECORD ALL Diagnostic Trouble Codes (DTCs) from the Generic Electronic Module (GEM). The following codes can be generated by a faulty relay:
  • B1371-Illuminated Entry Relay-Circuit
  • B1302-Accessory Delay Relay-Circuit
  • B1398-One-Touch-Down Relay-Circuit 1
  • B1814-Rear Wiper Motor Down Relay-Circuit
  • B1818-Rear Wiper Motor Up Relay-Circuit
  • P1820-Transfer Case L2H Relay-Circuit
  • P1824-Clutch Relay-Circuit
  • P1828-Transfer Case H2L Relay-Circuit
DIAGNOSIS
  1. If you have any of these codes B1371, B1814, B1818, and/or the interior lights or rear wipers are part of the customer concerns, go to Step 12. Otherwise locate the Accesory Delay Relay and proceed to next Step.
  2. Put key in "RUN."
    1. If conditions are repeatable, go to Step 3.
    2. If conditions are not repeatable, follow standard GEM troubleshooting procedures.
  3. Operate the windows until they fail then proceed to next Step.
  4. Remove relay from relay box then proceed to next Step.
  5. Check for battery voltage at Pin 87.
    1. If battery voltage is present, go to Step 6.
    2. If battery voltage is not present, go to Step 23.
  6. Check for battery voltage at Pin 86.
    1. If battery voltage is present, go to Step 8.
    2. If battery voltage is not present, go to Step 7.
  7. Locate the Battery Saver Relay and check Pin 3 for battery voltage.
    1. If battery voltage is present, go to Step 23.
    2. If battery voltage is not present, go to Step 16.
  8. Return the Accessory Delay Relay back to the relay box then proceed to next Step.
  9. Check for Ground at Pin 85.
    1. If Ground is present, go to Step 10.
    2. If Ground is not present, follow standard GEM troubleshooting procedures.
  10. Check for battery voltage at Pin 30.
    1. If battery voltage is present, follow normal GEM diagnostic procedures.
    2. If battery voltage is not present, go to Step 11.
  11. Check all female terminals at the relay.
    1. If all terminals are tight and all wiring crimps are good, REPLACE the Accessory Delay Relay, then go to Step 22.
    2. Make sure all terminals are tight and all wiring crimps are secure then go to Step 9.
  12. Locate the Battery Saver Relay.
  13. Put key in "RUN."
    1. If conditions are repeatable, go to Step 14.
    2. If conditions are not repeatable, follow standard GEM troubleshooting procedures.
  14. Operate the windows until they fail then proceed to next Step.
  15. Remove relay from relay box then proceed to next Step.
  16. Check for battery voltage at Pin 1.
    1. If battery voltage is present, go to Step 17.
    2. If battery voltage is not present, go to Step 23.
  17. Check for battery voltage at Pin 5.
    1. If battery voltage is present, go to Step 18.
    2. If battery voltage is not present, go to Step 23.
  18. Return the Battery Saver Relay back to the relay box then proceed to next Step.
  19. Check for Ground at Pin 2.
    1. If Ground is present, go to Step 20.
    2. If Ground is not present, follow standard GEM troubleshooting procedures.
  20. Check for battery voltage at Pin 3.
    1. If battery voltage is present, follow standard GEM troubleshooting procedures.
    2. If battery voltage is not present, go to Step 21.
  21. Check all female terminals at the relay.
    1. If all terminals are tight and all wiring crimps are good, REPLACE the Battery Saver Relay, then go to Step 22.
    2. Make sure all terminals are tight and all wiring crimps are secure then go to Step 19.
  22. Verify all concerns are corrected.
    1. If all concerns are corrected, return vehicle to customer.
    2. If all concerns are NOT corrected, go to Step 23.
  23. This is Not a GEM-related issue. Follow standard troubleshooting procedures.

PART NUMBER PART NAME F5TZ-14N089-B Relay - One-Touch-Down And Battery Saver FOAZ-14N089-A Relay - Accessory Delay F77Z-14B205-AA Generic Electronic Module (GEM) (1997 4X2) F77Z-14B205-BC Generic Electronic Module (GEM) (1997 4X4) F87Z-14B205-BA Generic Electronic Module (GEM) (1998 4X2) F87Z-14B205-CB Generic Electronic Module (GEM) (1998 4X4)
OTHER APPLICABLE ARTICLES: NONE
SUPERSEDES: 98-11-6
WARRANTY STATUS: Eligible Under The Provisions Of Bumper To Bumper Warranty Coverage
OPERATION DESCRIPTION TIME 981319A Perform Pinpoint Tests 1.0 Hr. 981319B Replace Relay 0.2 Hr.
DEALER CODING BASIC PART NO. CONDITION CODE 14B205, 14N089 42
OASIS CODES: 102000, 105000, 201100, 202000, 203200, 206000, 502000, 504000, 508000

Copyright © 1998 Ford Motor Company
2010&c18=modelyear&c21=98-13-19&c35=tsb%2c98-13-19&s=1366x768&c=32&j=1.3&v=y&k=y&bw=1329&bh=453&ct=lan&hp=n&[aqe]

Mar 10, 2011 | 1998 Ford Explorer

1 Answer

None of my windows work on the doors. i checked the#62 cb. and bought a new window switch and nothing.


my biggest concern with your problem is that fuse#6 and #2 are only part of the possible problem and those two are located in the BJB (battery junction box) under the hood

your primary focus should be on fuse #17 and the accessory delay relay located in the CJB (central junction box) under the dash

and then there is ground G400 @ the left D-pillar

fuse #17 powers the window when the accessory delay relay is energized, believe it or not, but a ground through the instrument cluster!!!

good luck and keep us posted


Mar 25, 2010 | 2003 Ford Explorer

1 Answer

Power windows do not work and no power. where is the relay located for a 1999 ford explorer


2 door or 4?

battery saver relay
accessory delay relay
one touch down relay

all should be behind center of dash

and then there is the possibility of a bad GEM


Mar 16, 2010 | 1999 Ford Explorer

Not finding what you are looking for?
2003 Ford Excursion Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...