Question about 2005 Dodge Magnum

Open Question

2005 dodge magnum sxt, After replacing the electronic throttle control sensor, do you need to reset the ETC & how?

I have a 2005 dodge magmum sxt 3.5 liter v6, and my etc light came on. After reading many blogs I ordered an electric throttle control sensor. I understand it is easy to install but my question is, will I need to reset the sensor after installation & can I reset it at home?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Molson02536
  • 3854 Answers

SOURCE: 2005 Dodge Magnum error code...

Your heated O2 sensor has a heeater problem most likely. Most likely time to change out your HO2 sensor. Most cars actually have only primary heated. Not sure for this application but would thus assume the primary sensor or otherwise known as precat O2.
With a sensor high you have high voltage back to the pcm thus most likely shorted heating element.

There is an outside chance of a cross short to the ground circuit of your O2 sensor. If after replacing your sensor you still have a problem then start looking for this.

I see you went to the auto parts store and got an HO2 sensor (Should be a 22mm or 7/8" -- same size) and replace the Primary and if that do not solve the problem, then see if you have a heated postcat HO2 if not then see above.

Good luck and hope this helps, oh and Bank 1 is where your #1 cylinder is.

Posted on May 13, 2009

Ad
emissionwiz
  • 77202 Answers

SOURCE: Location of Crank Sensor

Front of the engine near the the timing chain cover, this is a picture. Make sure the connector is clean and free of corrosion.



300? 300: true ); MAX-HEIGHT: 400px; ; HEIGHT: expression(this.height > 400? 400: true )" src="http://info.rockauto.com/getimage/getimage.php?imagekey=1005895&imageurl=http%3A//www.standardbrand.com/web_app/catalog/images/PC127.jpg" />

Posted on Aug 30, 2008

Murphybanton
  • 2004 Answers

SOURCE: unable to locate the fuel filter on my 2005 dodge magnum 2.7 liter

It's located in your fuel tank.

cheers.

Posted on May 21, 2009

  • 236 Answers

SOURCE: 2005 dodge magnum 3.5 liter engine. 10 deg start engine noise

these have a problem with the overhead cams, one or more of the bolts break which restricts the oil flow to the lifters.

Posted on Dec 31, 2009

  • 1 Answer

SOURCE: my Electronic Throttle Control (ETC) Light

I have the same problem. 2004 ram Quad cab with 5.7 hemi. Dealer has replaced throttle position sensor twice, computer once and rebuilt wiring harness twice. Now they say I should trade it in because they don't know how to fix it. It only has 64,000 miles on it. Still under powertrain warranty. The only solution I see is to find a good NON CHRYSLER mechanic and never buy a Dodge again.

Posted on Jun 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you clean the electronic throttle control on a 05 magnum 3.5L SLX


by removing lots of plastic and opening up the throttle body and spraying it with throttle body cleaner .

Apr 11, 2015 | 2005 Dodge Magnum SXT

1 Answer

How do you clean the electronic throttle control


have 2005 Dodge Magnum and the ETC light goes on and my car dies down when...

one 'trick' you should try: put the key in the "on" position, but don't start the car. Depress the gas pedal full to the floor, and then let go, all within 2 seconds. You should hear a "ding" sound indicating that the pedal travel distance has been reset in the PCM. Pedal position is electronically sensed at all engine conditions, and a misread can trigger the ETC code. You'll want to do this reset after you clean the throttle body, but try it first anyhow.

Apr 11, 2015 | 2005 Dodge Magnum SXT

1 Answer

The ABS and BAS lights are on in my 2005 Dodge magnum. What sensor does this point to?


It could also be a module failure. Normally I would take it to the dealer and when he tells you what is wrong you know what to replace.

Dec 19, 2014 | 2005 Dodge Magnum SXT

1 Answer

2005 dodge magnium sxt abs ebs light is on and coding to a right rear speed sensor and it was just changed. didn't fix the problem


Broken wire...Usually happens around the sensor, but could be anywhere from the rear sensor to the abs module. Just a note. Most wire breaks are just behind the plug. Within 1/2 inch.. Of the sensors.

Aug 27, 2014 | 2005 Dodge Magnum SXT

1 Answer

Does a bad battery affect the Electronic throttle control


Absolutely, bad batteries that will not take a full charge causes low battery voltage which can affect solenoid's, actuators, sensors and just about anything else including computer controlled operation. You'll need to replace the battery and sometimes in rare situations you made need to have the throttle control reset at the dealership. Hope this helps, and have an awesome day!

May 29, 2014 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

2007 dodge caliber etc light on


Get a can or two of carb & choke or intake cleaner. Take the intake boot off at the throttle, and clean it thoroughly. It miught help to use a small brush (like an old toothbrush) or some paper towels to help wip it out

Apr 05, 2014 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

Etc electronic throttle control light is on, 2010 dodge avenger sxt


Check throttle control relays. Alo, look at throttle positioning sensor, replace as needed.

Jan 21, 2013 | Dodge Avenger Cars & Trucks

1 Answer

The electronic throttle control light is on in my dodge magnum and my car is stalled what do I do to fix it?


Your throttle pedal is electronic and not controled by cables anymore. So there is sensor that sense's what postion your throttle body needs to be opened or closed. The sensor probably needs to be replaced.

The whole pedal assembly will have to come out and be replaced as it is all one unit. They are easy to take out. I learned about these at the SRT Track Expereince when the Charger that I was driving stopped having so much go and the ETC light came on. They showed us how to replace them and told us that they have to replace them all the time and keep them in stock due to people mashing the pedal. It is all plastic and you don't have to mash these like the old system.

You can try resetting the ETC as well. Place your car in the run position without starting and depress the gas pedal and release all in 2 seconds (1 down and 1 up). You should hear a confirmation "ding" if done correctly and you have know reset the sensor to know when you have open throttle.

You are still safe to drive your vehicle but you need to get it fixed or you are not going to get good performance.

May 25, 2011 | 2005 Dodge Magnum

1 Answer

How to change timming belt on 2005 magmum?


What size engine do you have?
Changing a timing belt is no small feat, and if you do not have the technical aptitude, I would not recommend doing it yourself. You could seriously mess up your engine.

Mar 27, 2011 | 2005 Dodge Magnum

Not finding what you are looking for?
2005 Dodge Magnum Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...