Question about Hyundai Cars & Trucks
I checked the chilton manual for these specs and it said that 10 ft. lbs or 14 NM was the spec but after I started to try to torque the bolts at this spec it just seemed that I was going to strip out the threads before I reached the specified torque setting. Is this information correct or not?
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: 2005 Tucson
camshaft sprocket bolt 58-72 ft. lbs. crankshaft pulley bolts 108-132 ft. lbs. crankshaft pulley center bolt 80-94 ft. lbs. cylinder head bolts cold engine 65-72 ft. lbs. warm engine 73-80 ft. lbs. cylinder head rear cover bolts 69-86 in. lbs. flywheel/Driveplate bolts 94-101 ft. lbs. intake/Exhaust manifold nuts/Bolts 11-14 ft. lbs. jet valves 13-16 ft. lbs. main bearing cap bolts 36-39 ft. lbs. oil pan bolts 51-69 in. lbs. oil pan nuts 43-60 in. lbs. oil pan drain plug 33 ft. lbs. oil pump cover bolts 72-84 in. lbs. oil pump relief valve plug 29-36 ft. lbs. oil pump sprocket nut 25-28 ft. lbs. Rear oil seal retainer bolts 84-108 in. lbs. rocker arm shaft bolts 14-15 ft. lbs. rod bearing cap nuts 23-25 ft. lbs. silent shaft sprocket nut 22-28 ft. lbs. spark plugs 15-21 ft. lbs. thermostat housing-to-Engine bolts 86-114 in. lbs. timing belt tensioner bolt 32-40 ft. lbs. valve cover bolts 43-61 in. lbs. water pump-to-Engine bolts alternator brace bolt 14-20 ft. lbs. all others 9-11 ft. lbs. water pump pulley bolts 72-84 in. lbs.
Posted on Sep 08, 2008
SOURCE: torque specs for toyota tercel
Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using FixYa. Roger
Posted on Apr 15, 2009
Main Bearing Cap Torque-42 Ft. Lbs.
Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 Degrees
Rod Bearing Nuts-29 Ft. Lbs.
Hope this helps
Posted on Sep 20, 2009
Torque in two to three stages.
Connecting rods are 24-26 lb.ft.
Main bearing caps are 41-44 lb.ft.
Hope this helps,Chuck
Posted on Dec 28, 2009
Testimonial: "Thanks for the help Chuck"
Tips for a great answer:
Dec 18, 2015 | Ford Cars & Trucks
Dec 18, 2015 | Cars & Trucks
Mar 25, 2015 | 2002 Chevrolet S-10
Feb 26, 2015 | Plymouth Cars & Trucks
Mar 14, 2013 | Chevrolet S 10 Cars & Trucks
Mar 27, 2011 | 1992 Dodge Dakota
Sep 24, 2010 | Hyundai Tiburon Cars & Trucks
Nov 13, 2009 | 2005 Nissan Sentra
Oct 12, 2009 | 1991 Mitsubishi Mighty Max
Feb 23, 2009 | 1994 Mazda Protege
1,021 people viewed this question
Usually answered in minutes!