Question about 2006 Pontiac G6

Open Question

2007 pontiac g6 v6 3.5 where is the cam actuator

Its saying my cam positioning sensor is out and the camshaft actuator where is the accuator located at please help me!!

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 55 Answers

SOURCE: replacing bad camshaft position sensor

  1. Disconnect battery ground cable.
  2. Remove water pump pulley attaching bolts, then the serpentine belt and water pump pulley.
  3. Disconnect sensor wiring connector and remove sensor retaining bolt.
  4. Twist and pull sensor to remove.
Reverse procedure to install and prior to installing new sensor, lubricate sensor O-ring.

It is located under the water pump. Make sure when you remove the sensor that you rotate the crank shaft and look in the hole to make sure the pick up magnet is still in there. Sometimes they come loose and cause a no start or long crank. You will need to have the code cleared still.

Posted on May 06, 2009

Ad
  • 60 Answers

SOURCE: where is the camshaft positioning sensor located

Lover camshaft position is near bottom line of the hatch cover

Posted on Aug 08, 2009

outdoorsman5
  • 631 Answers

SOURCE: Where Is The Camshaft Position Sensor Located On

Front of engine above crankshaft pulley. If you need a picture of it send me your email address and I will send you a picture.

Posted on Sep 10, 2009

Testimonial: "Thank you soooo much you hit the nail on the head without asking a million questions that don't pertain to what I need to know. You know your stuff!!!"

omaromid
  • 332 Answers

SOURCE: How to clean O2 sensor on a 2007 Pontiac G6?

O2 sensor are located before and after Catalytic Converter ( exhaust system of your car). If you car's engine is 4 cyl you have 2 O2 sensors and if you car's engine is 6 cyl then you have 4 O2 sensors ( for each bank, 2 for left bank and 2 for right bank). Hope it helps and comment if you need more advice. Please don't forget to rate the answer it helps with my ratings, thanks!

Posted on Apr 28, 2010

bluebirdmate
  • 1190 Answers

SOURCE: locate the tire pressure sensor on 2008 pontiac g6

The tire pressure sensors are part of the valve stem, one in each tire. Please check the tire pressure in each tire also the spare. If all are correct then you will have to diagnose the system with a scanner at a GM dealer or a name brand tire store.

Posted on Oct 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is cam shaft sensor located on a 08 saturn aura


Which engine ? This vehicle had option of six different engines , 2.4 , 3.5 , 2.8 , 3.0 , 3.2 , 3.6 And are you picking on the right part ? What code > DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit
It may not even be a cam sensor problem !
DTC P0340: Intake CMP Sensor Circuit

DTC P0365: Exhaust Camshaft Position (CMP) Sensor Circuit
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance
Camshaft Position (CMP) Actuator System
The camshaft position (CMP) actuator system is an electro-hydraulic operated device used for a variety of engine performance and operational enhancements. These enhancements include lower emission output through exhaust gas dilution of the intake charge in the combustion chamber, a broader engine torque range, and improved fuel economy. The CMP actuator system accomplishes this by changing the angle or timing of the camshaft relative to the crankshaft position. The CMP actuator simply allows earlier or later intake and exhaust valve opening during the four stroke engine cycle. The CMP actuator cannot vary the duration of valve opening, or the valve lift.
During engine OFF, engine idling conditions, and engine shutdown, the camshaft actuator is held in the Park position. Internal to the CMP actuator assembly is a return spring and a locking pin. During non-phasing modes of the camshaft, the return spring rotates the camshaft back to the Park position, and the locking pin retains the CMP actuator sprocket to the camshaft


It may

Jul 06, 2016 | 2008 Saturn Aura

1 Answer

P0014 Diagnostic code, already replaced camshaft actuator & oil twice


code p0014 - Chevy TrailBlazer, TrailBlazer SS and GMC Envoy Forum

forums.trailvoy.com > ... > OEM Issues

Sep 8, 2007 - 11 posts - ‎8 authors
On my Trailblazer I have a code P0014 . this says Camshaft Position Actuator B ... If the desired and actual cam phase angle error exceeds its ... This diagnostic procedure supports the following DTC: ... replace the camshaft actuator solenoid, change the engine oil and filter, ... 2004 Chevy TrailBlazer LT P0014 - Camshaft Position Actuator Solenoid "Relearn"
11 posts
Dec 11, 2009
cam crank sensor mismatch
11 posts
Jul 4, 2009
More results from forums.trailvoy.com

Tech Code "dtc P0014" 2003 Trailblazer - Chevy S-10/Blazer ...

www.gm-trucks.com/.../72278-tech-code-dtc-p0014-2003-trailblazer/

Dec 31, 2007 - 14 posts - ‎6 authors
Tech Code "dtc P0014" 2003 Trailblazer - posted in Chevy ... it had been serviced before for the same thing in 2003 or 2004! ... replace the camshaft actuator solenoid, change the engine oil and .... The extended war. co. prob. would not be to happy since they already fixed the sensor once or twice already.

Replace a Camshaft Position Actuator Solenoid Valve on a ...

? 8:05
https://www.youtube.com/watch?v=4Dkdd287AKg

Jan 11, 2016 | 2004 GMC Canyon

1 Answer

Wires came out of harness on cam position sensor on 2006 Pontiac g6


Your camshaft sensor is under the engine's cover. It is likely a black plastic piece connected to a large metal screwlike thing.--------------------------------------------------------------------------------
Multi-cardiag M8

Apr 08, 2013 | 2006 Pontiac G6

1 Answer

Where is the brake pedal position sensor in a pontiac g6


2007 G6 pontiac brake pedal position sensor location?

Oct 15, 2012 | 2006 Pontiac G6

1 Answer

2006 pontiac g6 clunking noise when shifting gears check engin light came on day after noise started p0014 code had it scaned by the nice atuo zone guy . He gave 4 possible causes 1 loose cam or crank...


Most likely the advance mechanism on the cam gear has jammed in the advanced position. You're going to have to take the cover off the gear to see what's going on. If there is sludge, you need to also desludge the engine.

Jun 07, 2017 | 2006 Pontiac G6

1 Answer

How do i replace the cam actuator solenoid on my pontiac g6


I had a code, po0014, my G6 has 81760 miles on it, I replaced my exhaust camshaft actuator solenoid in about
10 minutes, my check engine light went out and the transmission shifts normal now. I talked to some GM guys, they replaced alot of them. They say there is nothing I can do different, they it just happens.

May 25, 2012 | 2006 Pontiac G6

1 Answer

Pontiac g6 2007 p0014


P0014 Could be either a bad Camshaft position sensor, Or your timing is off!

Mar 23, 2012 | 2007 Pontiac G6 GT Convertible

1 Answer

What does the code P0011 mean and located


The code p0011 is for the intake camshaft position actuator performance.Some of the simple things to look for is make sure the oil level is where it should be and the condition of the oil is also crucial.This means that if the oil is not changed periodically.Which is about every 3 thousand miles.There is 1 actuator on each camshaft.One on the intake and one on the exhaust cam.If you are not familiar with the camshaft actuators you should take it to a reputable repair shop.Hope this info helped you.Good luck.

Dec 03, 2011 | 2006 Pontiac G6

1 Answer

Where is the cam shaft position sensor in a 2007 pontiac G6 4 cylinder


Hello,Thanks for using fixya.
this vehicle uses an intake and exhaust cam sensor they are both on the back of the head on each side I hope this answers your question

Nov 02, 2011 | 2007 Pontiac G6 GT Convertible

1 Answer

Where is intake camshaft position sensor


The intake cam sensor is located on the transmission end of the head, intake manifold side.
Hope this helps.

Dec 09, 2010 | 2006 Pontiac G6

Not finding what you are looking for?
2006 Pontiac G6 Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...