Question about 1999 Dodge Ram

Open Question

Heat blend door 1999 dodge ram 1500? replace - 1999 Dodge Ram

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
rockitman187
  • 2559 Answers

SOURCE: 1999 Dodge Ram 1500 2WD won't shift properly

Sounds like the speed sensor on the rear axle.

Posted on Jan 20, 2009

Ad
  • 840 Answers

SOURCE: passanger side mirror replacement on 04 dodge ram 1500?

very easy take the mirror inside cap off if you can not get to the 3 bolts then you will have to take trim panel off to take trim panel off look for plastic caps take them out and unscrew them then pop out the bottom of the door and pop the sides out then lift up and out should be loose enough for the bolts now/ 10mm bolts 3 Please rate my response thank you very much

Posted on Feb 02, 2009

  • 249 Answers

SOURCE: replace timing chain on 03 dodge ram 1500 with 5.7 hemi

i have an 02 and i purchased a repair manual from autozone

Posted on Jan 05, 2010

  • 159 Answers

SOURCE: The temperature gauge on my 1999 Dodge Ram 1500 is

Check the gauge by holding in the trip odometer reset button and turn key to run,hold button for 10 seconds this will iniate a diagnostics on all the gauges,and lights if gauge doesn't move during this test replace gauge,if it does move then check the wires on the plug at the engine coolant temp sensor (ects) you can check the sensor by using a ohms meter by unpplugging it and check ohm's or resistance when cold and then start engine as the engine warms up the ohm's reading should gradually lower as the sensor is a thermister and as it warms up the resistance will drop.

Posted on Jun 05, 2010

  • 834 Answers

SOURCE: 1999 dodge ram 1500 5.2L timing,plug gap,firing order

You will find the spark plug gap and timing specifications listed on the vehicles emission label under the hood, and those specifications are the ones to be used on that vehicle and engine for that year, and no other specifications should ever take precedence over the specifications listed on the vehicles emission control label. Here is the firing order diagram for that engine, let me know if you require any further assistance, and I an curious as to how you got taken for $2,000.


6ad2c81.gif

Posted on Jun 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I got all speeds on the blower motor and heat only on front ac vents. it won't go to defrost and to ac mode?


Temp blend door may be stuck. If it also will not go from defrost to AC the mode door may be bad also. Possible linkage or connection issue .

Feb 22, 2016 | 1999 Dodge Ram

1 Answer

I have 2001 dodge ram 1500 3.9 my air worked fine till I dropped dash and changwd heater core now no air just heat is that blend soor or control knobs?


Sounds like you may have forgotten to plug in one of the blend door motors or one of the blend doors has been disturbed and is binding or nor operating properly. Highly unlikely anything to do with the controller on then dash

Apr 25, 2015 | Dodge Cars & Trucks

1 Answer

I ahve a 2003 dodge ram 1500 , i have flushed cooling system and heat still blows cold. when i shut fan off for a few minutes and turn back on, it blows hot for a second then back to cold. i looked on both...


Could be your thermostat is staying open and not letting your coolant to heat up,usually this is the first thing to check,also your blend door could not be opening all the way.Here's how to replace thermostat.Here's the blend door.

Jan 01, 2013 | 2008 Dodge Ram Pickup 1500

1 Answer

My 2007 Dodge Ram 1500 seems to not be pumping heat from the floor vents, only the dash and defrost vents. Could it be a problem with the blend door? if so where do i find it and what should I do. This...


Yes, it's a blend/mode door problem. Seems like it was pretty common for a few years. I've heard that Dodge has switched manufacturers for this part.

There's no easy fix for this. The dash and the hvac box have to be removed to get to the blend doors. You also have to disconnect the A/C lines and then recharge them...

Any chance you're still under warranty?

Here's a link to a website that has info and parts about the issue. (no affiliation)

http://www.heatertreater.net/Ram%2002-08%20Listing.html

Jan 28, 2011 | 2007 Dodge Ram 1500 Quad Cab Sport

1 Answer

I think I have a blend door problem just not sure how to fix it. I get heat from my mid and lower vents on the drivers side but it blows cool on passenger side and defrost both sides. Magically the next...


this unit is eclectric, it uses actuator motors to control the blend doors and selector doors, you are correct its a blend door problem, if you look under the dash on the passengerside there will be a motor mid way, thats the blend door actuator and theres another on the driverside. you what pass/side. move your controls to pin point the right one,hope this helps.

Sep 21, 2010 | 2006 Dodge Ram 1500

1 Answer

I only get heat when the ac is on why? its a 1998 dodge 1500


you have a defective blend door actuator or door

Dec 13, 2009 | 2004 Dodge Ram 1500

2 Answers

2003 DODGE RAM 1500 HEAT BLOWS DEFROST OR DASK


there is a directional door actuator motor,that has gone bad.

Nov 19, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

I have a 1995 Dodge Ram 1500 V6. When the A/C


if the compressor is cycling the problem is not the fixed orfice, it is very likely the temperature control blend door actuator has failed and the blend door is stuck in the heated air position. .

Sep 16, 2009 | 1995 Dodge Ram

1 Answer

I replaced my evaporator in my 1999 dodge ram 1500 now i have no heat. everything feels cold.


The blend air door motor is not working or needs calibration,if mechanical the cable is not adjusted right.

Jul 15, 2009 | 1999 Dodge Ram

2 Answers

No heat


No heat can mean low coolant in the radiator. Check that. Also would mean you have a coolant leak. Might possibly be a restricted heater core. Possibly a blend door in the dash that quit working. Thermostat could be faulty allowing coolant to flow continuously.

Apr 01, 2009 | 2004 Dodge Ram 1500

Not finding what you are looking for?
1999 Dodge Ram Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...