Question about 2004 Chevrolet Colorado

Open Question

2004 chevy colorado axle nut size

What size is the main nut that hold the hub bearing set on?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 72 Answers

SOURCE: Front Hub Bearing Torque specs to complete replacement

THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Posted on May 09, 2009

  • 82 Answers

SOURCE: How do you get the front rotors off of a 2004

If this is a 4wd the rotors are "captured" and machined on the truck using an on car lathe. Otherwise you should get a printout of all the steps from a dealer.

Posted on Jun 22, 2009

  • 346 Answers

SOURCE: what size is the drive axle nut on an 02 chevy

It's either 32 or 36mm. I believe 32. You can "borrow" the socket size that you need from your local AutoZone parts store.

You pay for the tool, then when you bring it back, they give you your money back. It's a program they have for tools that the average person doesn't use more than once or twice.

Posted on Dec 27, 2009

  • 35 Answers

SOURCE: 2000 chevy blazer drive axle hub nut torque

I am not positive but I think it is 250ft lbs. Call a local dealer they can tell you for sure

Posted on Jan 30, 2010

  • 74 Answers

SOURCE: What is size of hub axle nut on 2002 chevy s10?

2002 chevy S10 ZR2

36 mm.
Torque 103ft pounds.

Posted on Mar 16, 2010

Testimonial: "Great, thank you! At 7 to 15 bucks a pop for one socket, it helps to buy the right one the first time."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't remove front wheel bearing hub on 2004 chevy express 1/2 ton. any suggestions


I presume you are trying to REPLACE the hub assembly? If so, you do not have to worry much about dammaging it. Simply take the three bolts out of the inboard side of the steering knuckle and beat it with a large hammer.

If your van is equiped with All-Wheel Drive, you must remove the large nut from the axle first to do this. Then the axle can be pushed in far enough to gt clearance to get the bolts out of the steering knuckle that hold the bearing assembly. Two-Wheel Drive is much easier.

It is also recommended that you disconnect the wheel speed sensor wire harness before trying to get the hub loose. Damage to the vehicle harness can result if the bearing comes out suddenly and pulls on the cable.

Nov 08, 2011 | 2004 Chevrolet Express

2 Answers

How remove the rotor to change bearing for 2005 chev colorado front


first you remove all the lug nuts and the wheel and tire. To get the rotor off you will need to remove the brake caliper. they are held in with 1/4" hex screws. If you don't have an allen wrench you can use a socket extension to removes these. Once unscrewed the calpet simply lifts off the rotor and the rotor is ready to come off. You will need to remove the axle nut and keeper then the rotor slides off towards you and the wheel bearings will come out with the rotor.

Sep 26, 2011 | 2005 Chevrolet Colorado

1 Answer

What is the foot pounds for the front wheel bearings on a 1995 chrysler cirrus


Hello, If you Chrysler has replaceable wheel bearings and seal. This is the way it goes---pack the wheel bearing with new grease-install the bearing in the wheel nub--install new back wheel seal--coat the axle shaft with grease lightly, thing coat-----install wheel hub on to axle shaft...be careful here don't damage the rear hub seal------------insert front race washer---install axle shaft nut--tighten nut down wheel nut until it is firm with water pump pliers----spin the hub/with tire mounted.
(the wheel and hub will turn but not freely)----take the pliers and back off the axle nut 1/4 turn----now spin the wheel and axle hub, it should spin freely---now if doesn't spin freely---back off the axle nut about 1/16 or 1/32 (or just a little bit)-----now, spin the wheel and hub and if turn freely------------Now grab the top of the wheel/tire and move it back and forth.-----if there is some movement ---try tighten the axle nut just a little little bit, unit the one can barely feel some little movement in the wheel/tire and hub.-----------Now, spin the wheel/tire and hub and it should also turn freely.

If it does----install new and correct size of cotter pin and bent the ends around the axle nut.----

coat the inside of the hub cup with grease. Now, use an rubber or plastic hammer to install the cup on the wheel/tire hub. You are finished with one wheel bearing maintenance. Now do the other side.



I really don't know if you Chrysler Cirrus has replaceable wheel bearing. All the auto/trucks have replaceable hubs, that means that the replacement is total hub with axle shaft, sealed bearings, and seals. This is bolt to each wheel steering hub. This work to remove these one unit hubs.

Four bolts hold the axle hub to the steering hub. Hear is the problem!! it has rusted to the steering hub. Also, these hubs cost more than replacing bearings, races, seals to cool turn of $180 to $250+ I wish you luck in your replacement of wheel bearing on your Chrysler. GB..stewbison

Sep 24, 2011 | Chrysler Cirrus Cars & Trucks

1 Answer

How do I rgerplabe how do I replace a front wheel bearing?


TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Mar 21, 2011 | 1999 Oldsmobile Alero

1 Answer

How do I change front hub and bearing assembly on 2004 Explorer


Front hub bearing, remove tire, remove caliper and caliper holding bracket, you do not have to remove brake caliper from brake hose, just set it aside, if 4X4 remove front axle nut that goes through center of rotor, also remove brake rotor, disconnect elec, A.B.S connector, remove three bolts on back side of hub bearing, remove hub bearing, some times you will need to knock hub bearing out with a hammer.Reverse to install new hub bearing.

Jul 09, 2010 | 2004 Ford Explorer

2 Answers

I have a 2004 Chevy Colorado and can not get the hub off to change out my front rotors.


Very, very few cars or trucks require the hub to be removed. In almost all American vehicles, the rotors are just resting on the hub and will come off fairly easily. Make sure you've removed the caliper, then smack the rotors a bit with a rubber mallet. They should come off. If there's a ton of rust, you might need to use some penetrating oil, then smack them a little.

Sep 01, 2009 | 2004 Chevrolet Colorado

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

2005 chevy colorado 4cyl


If you drove this truck with a lose wheel bearing you will have to change the bearing/hub. Now the large nut in the center of the axle is reuseable. I have been doing it for years and never had to replace one unless I had to change the axle itself. The nut is locked in place by a castle nut, it is pressed out of steel. The cotter pin passes through the castle nut to lock it in place. You can pick one up at any wrecking yard if you want to remove it. The nut size is a 32- 36 mm. I'm in Canada. And most auto stores like Parts pro? will lend the tool out for free. They also have online video to help you repair the axle. I hope this helps. If you take on the repair, you can spend a good afternoon on it if you are not use to doing that kind of work. Let me know how you make out.

Mar 16, 2009 | 2005 Chevrolet Colorado

1 Answer

Front wheel bearing 2004 escape 4x4


It's nearly impossible unless you have a good air compressor and a powerful 1/2" or larger drive impact gun.The reason is you have to remove the cv axle nut and axle out of the way before removing the bearing and hub.The axle nut requires a couple hundred foot pounds to remove.The procedure is:Jack vehicle safely off the ground,remove wheel and tire.Remove axle retaining nut.Remove balljoint nut and bolt,pry down on lower control arm,and disengage balljoint and lower arm from spindle.Now the axle can be released from the hub,but leave the other end of the axle in the trans,just set off to the side out of the way.At this point,there are two ways to change the bearing.The wheel bearing is a double roller,cartridge type with the hub containg the wheel studs,pressed into the bearing.Remove the entire spindle assembly from the suspension strut,OR leave the spindle attached to the strut,and remove the bearing and hub from the spindle.Some guys swear by taking the spindle to a press,and pressing the bearing assembly out with a bottle jack.I just use a bushing driver set,and ball peen hammer,and remove the hub from the bearing...then remove the snap ring retaing the bearing in the spindle,then drive the bearing out of the spindle with the hammer and drivers.There you have it.Reverse procedure for reassembly

Jul 11, 2008 | 2004 Ford Escape

Not finding what you are looking for?
2004 Chevrolet Colorado Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...