Question about 2002 Ford SVT Focus

Open Question

Ford focus code p1381,p1518

The engine no run good

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 123 Answers

SOURCE: 1999 ford windstar code P1518

This code means the intake manifold runner is stuck open either from a faulty actuator on the intake or the valves plates are gunked up unable to move,

Posted on Jul 19, 2010

  • 1 Answer

SOURCE: 2003 FORD FOCUS. WHEN

well.. I have the exact same problem and I am still trying to figure out what is causing it. So far I've tried: new spark plugs, fuel injectors, cam/crank sensors, ignition control module (I think.. my brother did the work). If you figure it out before you get rid of the hunk of junk let me know. I like not having a car payment and the gas mileage is better than my Jeep. =] btw - I will never buy a Ford again, while dealing with the herky jerky problem. I have also had the following go wrong: ignition wouldnt turn, clutch went out, and the trunk latch is on the fritz.

Posted on Jan 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1518 engine code


P1518 Intake Manifold Runner Control Stuck Open (Bank 1)
Sorry no idea what this means ,but i suspect the valve on the fuel rail the one with the vacumn pipe to it ?'

May 23, 2013 | 2001 Ford Focus

1 Answer

1999 ford contour p1381 error code


P1381 Camshaft Position Timing Over Advanced (Bank 1)
Take vehicle back to the garage as it sounds like the sensor is loose or not plugged in.After paying all this money for the work to be done they should have it put right for free straight away and they should give you a cortesia car with a free tank of fuel while they put yours right

May 18, 2013 | 1999 Ford Contour

1 Answer

I have a 2003 ford mustang v6, throwing code p1518.


its your intake manifold runner. its a silver box. they all go bad. ether a corroded chip bord or the bar falls off that controls it. If you hear a rattle sound coming from the dash its a barr that fell off if no sound then corrosion. ford wants 600 to fix this but you can do it yourself without bying a new one. ill try to post a link.

http://passionford.com/forum/ford-focus-st/400597-st170-fault-code-p1518.html

Mar 16, 2013 | Cars & Trucks

1 Answer

Ford F140 4.2 Do Engine codes P0305, P0306, and P1518 relate to each other


I am assuming you mean F150 truck.
The answer is maybe.
Code 305 and 306 are missfire codes for cylinders 5 and 6.
Code 1518 is for a problem with the intake manifold runner control which could cause the other two codes.

P1518 FORD Description The Intake Manifold Runner Control (IMRC) is monitored for failure during continuous or key ON engine OFF self-test.
Possible causes - Intake Manifold Runner Control (IMRC) harness is open or shorted
- Intake Manifold Runner Control (IMRC) circuit poor electrical connection
- Faulty Intake Manifold Runner Control (IMRC) actuator
- Faulty Engine Control Module (ECM)
Read more: http://engine-codes.com/p1518_ford.html#ixzz2KSN6Thui

Feb 10, 2013 | Ford Cars & Trucks

1 Answer

I have a p1518 on Ford windstar 99 3.8.


For error code P1518 troubleshooting,click the link below :----http://schematicsdiagram.blogspot.in/2012/03/obd-code-p1518-on-ford-windstar.html
--------This will help.Thanks.

Mar 03, 2012 | 1999 Ford Windstar

1 Answer

2005 for escape,, stopped running,, wont start,, changed cam and crank sensors,, mechanic said no signal coming from new cam sensor that checks good OFF of engine,, wiring has been checked,,crank sensor is...


P1381 Cam Timing Advance is excessive if it were that your check engine light would be on it would be throwing code were gonna test what hes saying

Dec 11, 2010 | 2005 Ford Escape

1 Answer

How do i fix p1518 code on 1999 ford windstar?


P1518 - Intake Manifold Runner Control Malfunction (Stuck Open) The IMRC system is monitored for failure during continuous, key ON engine OFF or key ON engine running self-test.

The test fails when the signal on the monitor pin is less than an expected calibrated range at closed throttle.
* IMRC monitor signal circuit shorted to PWR GND or SIG RTN
* Damaged IMRC actuator
* Damaged PCM

Hope this info helps

Jun 21, 2010 | 1999 Ford Windstar

1 Answer

1999 ford windstar code P1518


This code means the intake manifold runner is stuck open either from a faulty actuator on the intake or the valves plates are gunked up unable to move,

Jun 17, 2010 | 1999 Ford Windstar

1 Answer

2002 F150 v6-4.2L I have a service engine soon ligth on. Install a reader and the code is P1518 manufacturer controlled vehicle speed, Idle control & auxilliary inputs.


YOUR DIFINITION IS INCORRECT, HERE IS THE CODE FROM THE FORD REPAIR MANUAL

P1518 Intake Manifold Runner Control (Stuck Open)
CHECK FOR DISCONNECTED INTAKE RUNNER CONTROL VALVE LINKAGE AT UPPER PLENUM CHAMBER

Oct 09, 2009 | 2002 Ford F150 Regular Cab

Not finding what you are looking for?
2002 Ford SVT Focus Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...