Question about 2001 Kia Sportage

1 Answer

My breakes dont work till they are almost to the floor

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 2 Answers

Try pumping the brake pedel. If the pedel travel comes up, the rear brakes need to be adjusted. If the pedel does not come up, it could be a bad master cylinder or a broken brake line.

Posted on Jan 07, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ok about a month ago my rear passenger brake locked up when it was wet. It slid a little but I got stopped. It only did it that one time. And about 3 weeks ago I drove it to the store that night and it...


They're probably right probably is the master cylinder but now you have Air the lines so you will have to fill up resivor then pump the brakes up and crack the line then you will need to keep the brake pedal depressed till you close the line it takes 2 people repeat process over and over till fluid comes at you must remember to fill the main reservar as you do this if you get all the air and still have brake problems it means that it probably is the master cylinder but it doesn't hurt to change the brake fluid at anyway

Aug 07, 2014 | Cars & Trucks

1 Answer

Abs lights goes on and the car is in second gear for awhile and then kicks into third gear


your breaks hardware do for inspection this is a safety device built in car to lower speeds when breaks are bout to fail dont drive vehicle in condition till you have the break system checked out

Nov 09, 2013 | 2001 BMW 5 Series

1 Answer

Breaks spongy go all the way to floor before a slowly loud grinding stop


Some ABS equipped vehicles require a scanner to activate ABS valves to allow for proper bleeding of air.

Feb 17, 2013 | Cars & Trucks

1 Answer

Bleed abs unit


Find the bleed valve located on the caliper. Have car on and have a friend or someone pump the breaks 6-10 times then hold them in. While they have the pedal pushed in open the valve (pedal will go to floor warn them, they need to keep it down though dont let up)close the valve then they can release pedal. Do so all the way around the car stating farthest away from master cylinder: BR, BL, FR, FL. and do as many times as necissary till no air spits out when you first open valve.

Jul 27, 2010 | 2000 Volkswagen Beetle

2 Answers

Breaks will not work at random times?


YOU HAVE A BAD MASTER CYLINDER
HAVE IT REPLACED AHD YOU PROBLEM WILL GO AWAY

Mar 02, 2010 | 1995 Toyota Camry

1 Answer

Electrical


There seems to be a break in the electrical circuit which is not getting contact, which only happens after u pull the ebrake one notch, however if it is not causing any operational problems then continue to do so till more probs arise.....................sodeep

Jun 18, 2009 | 1991 Honda Prelude

2 Answers

How do you bleed brakes on a 1999 GMC Sierra with ABS 2wheel drive 1500 series


The rule of thumb is to start as far away from the master cylinder as poss. so it means you start at the right rear, left rear, right front, then at last left front. There is a little a little weep bolt on each calliper it needs to be un lossened when break is fully applyed then tighten weep bolt back up pump the breaks while weep bolt is still tight then hold brake pedal down to floor lossen weep bolt till a full steam of fluid comes out tighten bolt back up, now move on to the next break calliper and repeat this same proccess till you finished. Hope this works better than r/r l/r r/f l/f lol!!!!

Mar 12, 2009 | 1999 GMC Sierra

1 Answer

How to change front breaks on a 99 jeep grand cherokee learado


Have it towed to a trustworthy shop. If the pedal is hitting to floor there is more wrong than just the brake pads!!!

Jan 29, 2009 | 1996 Jeep Grand Cherokee

1 Answer

98' mercury mystique break problem


You most likely have had the Brake master hydraulic cylinder go out, if u don't know cars this is a job for a shop to repair.

Jan 08, 2009 | 1998 Mercury Mystique

Not finding what you are looking for?

Open Questions:

See all 2001 Kia Sportage Questions

2001 Kia Sportage Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...