Question about 1993 Mercury Villager

1 Answer

OBD-I WHERE IS THE WIRING HARNESS TO PLUG IN AN OBD-1 CODE READER ON THE 93 MERCURY VILLAGER?

Posted by on

  • Anonymous Mar 14, 2014

    93 mercury villager distrubutor makes noise

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

Under the Dash on the Drivers Side Left Torwards the Door. on this Model they are Really close to the Bottom of the Dash.

Posted on Jan 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fix my Mercury Villager 2002 with random misfire?


How to Fix error code P0300 for random misfires on your car ...

diy-auto-repair.wonderhowto.com/.../fix-error-code-p0300-for-random-...
Oct 15, 2010 - How to Fix error code P0300 for random misfires on your car ... amisfire (code P0304) on a 1999 Mercury Villager 3.3L · How to Fix error code P0500 ... I reset my codes and it ran fine for a couple of days, then I started getting ...

(code P0305) on a 1999 Mercury Villager 3.3L - auto repair

diy-auto-repair.wonderhowto.com/.../troubleshoot-misfire-code-p0305-1...
Sep 7, 2010 - The vehicle is a '99 Mercury Village, 3.3L, with 150000 miles on it. The chief ... How to Fix error code P0300 for random misfires on your car ...

2000 Villager Misfire - Car Forums and Automotive Chat ...

www.automotiveforums.com > ... > Mercury > Villager
May 24, 2010 - 2000 Villager Misfire Villager Car Forums. ... i was told that the 3.3L engines of 1999-2002 nissan quests/ mercury villagers are INTERFERENCE engines! ... Hope the following may help, and I will post if my last fix works. ... I have a 1999mercury villager that is showing a random multiple cylinder misfire ...

Rough Idle - 2000 Mercury Villager - RepairPal

repairpal.com > Questions > Mercury > Villager > 2000 Mercury Villager
Repair the code issue, because your Villager has OBD-II which is a very helpful Diagnostic system. Upvote (4) ... My 1999 Villager was running poorly; rough idle, lack of power at highway speeds and the engine problem light indicated random miss-fire, etc. I had new spark ... Have code po306 cylinder 6 misfire detected.

P0301 - OBD-II Trouble Code - RepairPal


Dec 17, 2015 | 2002 Mercury Villager

1 Answer

Code P01705


P1705--Transmission Range Sensor out of self test

TYPE: 2000 Mercury Villager OBD P1705

and read up

Aug 13, 2014 | 2000 Mercury Villager

1 Answer

On a mercur capri 1991 is there a obd 1 code reader plug


The OBD I plug will be in the engine compartment Under hood, driver side, behind strut tower, mounted in corner relay block

Jul 16, 2011 | Mercury Capri Cars & Trucks

1 Answer

My saab 93 showed error code P0100. I renewed the mass flow sensor but the error code and the poor performance is still there. the revs are limited to approx 3500.


P0100 OBD-II Trouble Code

Technical Description

Mass Air Flow (MAF) Circuit Malfunction

Basically this means that there's a problem with the Mass Air Flow (MAF) sensor or circuit.

You will likely not notice any serious driving problems, but there may be symptoms like a general decrease in power or sluggishness.
Causes

A code P0100 may mean one or more of the following:

* The MAF may be disconnected, or a wiring connection may be bad.
* The MAF sensor may be faulty.

Possible Solutions

Use an OBD II Reader (or go tou your local parts store and they will for free) and reset the code and see if it comes back.
Then start with the cheapest, easiest repair procedures:

* Check the Mass Air Flow Sensor wiring/harness is connected properly and that there are no broken / frayed wires.
* Unplug and reconnect the MAF wiring harness a few times to clear the contacts.
* Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information).
* Replace the MAF sensor.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
!$!$

Sep 23, 2010 | 2001 Saab 9-3

2 Answers

93 mercury villager check engin light comes on for 2 days then off for a day then back on i dont know where to plug in my scanner


I too have a 93 Villager. Recently the check engine light came on especially on the highway cruising speed and it turned out to be caused by clugged EGR. My mechanic cleaned up the carbon build-up ( not replace EGR) from all those 170K miles and it seems to fix the problem. He charged me $150 for the labor only. Also the gas mileage seems to improved a bit as well.

Oct 27, 2009 | 1993 Mercury Villager

1 Answer

My 1998 mercury villager have check say obd mil


need more info. was this a state test it failed?

go here for villager expert help.

http://autos.groups.yahoo.com/group/villagerquest/

Jun 13, 2009 | 1998 Mercury Villager

1 Answer

Timing belt settings for a 93 mercury villager 3.0


The left cam should be set @10:00 and the right @ 2:00 the crank @ 5:00

May 06, 2009 | Mercury Villager Cars & Trucks

1 Answer

Door issue


no difference from 93 to 98. you need to move door hinges.

go here for villager/quest help

http://autos.groups.yahoo.com/group/villagerquest/

Apr 18, 2009 | 1993 Mercury Villager

2 Answers

98 mercury villager OBD I code P0135


This code refers to the front oxygen sensor on Bank 1. The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0135.
Repair short or open or high resistance in wiring harness or harness connectors.
Since you have already changed out your O2 sensor (as long as you used to OEM replacement and not the "Universal" replacement) you should not have to replace it again. You might check your thermostat to part of the time it takes for the O2 sensor to start switching being based on coolant temp, if your thermostat is not operating properly, it could cause the coolant temp to take longer than what is considered by the ECM to be normal.

Feb 22, 2009 | 1998 Mercury Villager

Not finding what you are looking for?
1993 Mercury Villager Logo

Related Topics:

431 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...