Question about Chevrolet Silverado

Open Question

I need to install a heater core on my 1981 chevy c10

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
gregstobbe
  • 56 Answers

SOURCE: CHEVROLET C10

you will have to go to the site below and choose fig 3 for the fuse box diagram
hope this was helpfull.
http://www.autozone.com/addVehicleId,1237304/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c1528004c636

Ps. dont forget to rate my solution please. Thanks

Posted on Dec 27, 2008

Ad
  • 289 Answers

SOURCE: How to replace a heater core in a 1994 chevy 1500

As with all vehicles it seems the first part that they build around is the heater core. It is under the dash above the floor housed in a black plastic sealed box. Sealed with goop. Locate that box and start removing everything around it that is peventing taking the cover off. Of course disconnect the heater hoses under the hood a thefirewall.

Warning it is never as easy as it sounds.

Posted on Nov 29, 2009

  • 61 Answers

SOURCE: how to replacemy heater core in a 92 chevy caprice

with or with a/c

Posted on Dec 13, 2009

Jim1969pa3
  • 152 Answers

SOURCE: I have a 1999 chevy silverado and I need to change heater core

Not a whole lot different. Just need to keep removing plastic down at the heater until you get to the heater core. Then disconnect it on the firewall side.

Posted on Dec 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My door is stuck shut and wont open i have a 1981 chevy c10


Check backup light with ignition switch on and car in reverse.

Jul 22, 2013 | Cars & Trucks

1 Answer

1981 chevrolet c-10 only reverse works


No specific information found on the 1981 Chevy C10 wheel lug spacing. -----------------------------------------------------------------------
fgtech galletto 2-master

Dec 03, 2012 | Cars & Trucks

1 Answer

Diagram for dual fuel tank switch 1981 chevy c10


I am sorry but we do not have the factory service manual for this truck, it contains these diagrams.

Jul 15, 2012 | Chevrolet 1500 Cars & Trucks

1 Answer

1981 Chevrolet C10 starts up but will not move in any gear... any ideas?


If the transmission is full then you have a failed transmission,

Feb 16, 2012 | Cars & Trucks

1 Answer

Is the heater core on a 1981 bronco in the engine compartment or the cab compartment


in the cab, but procedures are different depending on whether or not you have A/C. See below

1980-81 Comfort Vent Heaters, Without Air Conditioning
  1. Disconnect the heater hoses from the heater core tubes and plug the hoses with suitable 5 / 8 inch; (16mm) plugs.
  2. Remove the glove compartment liner.
  3. Remove two (2) spring clips attaching the heater core cover to the plenum along the top edge of the heater core cover.
  4. Remove eight (8) screws attaching the heater core cover to the plenum and remove the cover.
  5. Remove the heater core from the plenum taking care not to spill coolant from the core.
To install:
  1. Install the heater core in the plenum.
  2. Install the heater core cover (eight (8) screws and two (2) spring clips along the top edge of the cover).
  3. Install the glove compartment liner.
  4. Connect the heater hoses to the heater core. Tighten the hose clamps.
  5. Add coolant to raise the coolant level to specification.
  6. Check the system for proper operation and for coolant leaks.

1980-81 Standard & High Output Heaters, Without Air Conditioning
  1. Disconnect the temperature cable from the temperature blend door and the mounting bracket on top of the heater case.
  2. Disconnect the wires from the blower motor resistor and the blower motor.
  3. Disconnect the heater hoses from the heater core and plug the hoses with suitable 5 / 8 inch; (16mm) plugs.
  4. Working under the instrument panel, remove two (2) nuts retaining the left end of the heater case and the right end of the plenum to the dash panel.
  5. In the engine compartment, remove one (1) screw attaching the top center of the heater case to the dash panel.
  6. Remove two (2) screws attaching the right end of the heater case to the dash panel, and remove the heater case from the vehicle.
  7. Remove nine (9) screws and one (1) bolt and nut attaching the heater housing plate to the heater case, and remove the heater housing plate.
  8. Remove three (3) screws attaching the heater core frame to the heater case and remove the frame.
  9. Remove the heater core and seal from the heater case.

To install:
  1. Position the heater core and seal in the heater case.
  2. Install the heater core frame (3 screws).
  3. Position the heater housing plate on the heater case and install the nine (9) screws and one (1) bolt and nut.
  4. Position the heater case to the dash panel and install the three (3) attaching screws.
  5. Working in the passenger compartment, install two (2) nuts to retain the heater case and plenum right end to the dash panel.
  6. Connect the heater hoses to the heater core. Tighten the hose clamps.
  7. Connect the wires to the blower motor resistor assembly.
  8. Connect the blower motor wires.
  9. Position (slide) the self-adjusting clip on the temperature cable to a position approximately one 1 inch; (25.4mm) from the cable end loop.
  10. Snap the temperature cable on the cable mounting bracket of the heater case. Then, position the self-adjusting clip on the door crank arm.
  11. Adjust the temperature cable.
  12. Check the system for proper operation.

Oct 05, 2010 | 1981 Ford Bronco

1 Answer

Antifreeze leaking into cab under glove comp.


heater hose or heater core you can solder the heater core if you can find the leak oh and if the rest of it is good

Nov 22, 2009 | 1984 Chevrolet Chevy

1 Answer

How tough is it to replace heater core on '85 chevy c10?


shouldnt be hard at all on pass side under dash being a truck you should have plenty of room. line run thru fire wall and hook up to rubber hose under hood 1 hour at the most

Oct 30, 2009 | 1985 Chevrolet Chevy

1 Answer

How to install striker on door jam of 1985 C10


It unscrews counter clockwise. More common is the metal around the area fatigues and needs to be built up...

Sep 18, 2009 | 1985 Chevrolet Chevy

2 Answers

HAVING TO PUSH THE STICK SHIFT UPWARD 1981 chev c10 truck


if it is an automatic a lot of newer cars are made that way its a saftey feature

Jun 03, 2009 | 1995 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...