Question about Cars & Trucks

Open Question

Harmonic balancer removal on a 98 buick century 3.1

Posted by Anonymous on

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 buick century


If you know it is the wobble on the balancer. Replace the balancer. Balancers that slip will cause vibration also.

Feb 03, 2016 | Buick Cars & Trucks

1 Answer

Where is the crank sensor on a 2000 Buick Century


Which one ? your vehicle has two !
Crankshaft Position (CKP) Sensor (7X)
Lower rear of the engine block, below the exhaust manifold
Crankshaft Position (CKP) Sensor (24X)
Right side of engine, at the end of the crankshaft, behind the harmonic balancer
24x replacement .
Turn OFF the ignition. Remove the serpentine drive belt from crankshaft pulley. Refer to Drive Belt Replacement in Engine Mechanical. Raise the vehicle on hoist. Refer to Lifting and Jacking the Vehicle in general information. Remove the crankshaft harmonic balancer. Refer to Crankshaft Balancer Replacement in Engine Mechanical. Note the routing of sensor harness before removal. Remove the harness retaining clip with bolt (1). Disconnect the sensor electrical connector. Remove the sensor bolts (2). Remove the sensor.
After replacement of this one you have to do relearn
24x 24

Dec 11, 2015 | Buick Cars & Trucks

1 Answer

REMOVING HARMONIC BALANCER


to remove the balancer you will need to remove the belt, the remove the bolt off the balancer then use a puller to remove the balancer,to install line up the key way slide balancer back on and then tight bolt,

May 13, 2010 | 1992 Buick Century

1 Answer

How to replace harmonic balancer?


jack up vehicle ,remove passenger side front tire remove plastic splash shield now under hood find your serpentine belt tensioner release tension on belt and remove belt now back at the plastic shield with it removed you should see your harmonic balancer install correct puller onto balancer and remove

Mar 16, 2010 | 2001 Buick Century

1 Answer

I need to know what size wrenches are needed to replace harmonic balancer and crank sensor on my 1989 buick century 2.8 ltr. engine


you will need sockets,the crank bolt i belive is 22mm and you might need in impact wrench to remove bolt. the crank sensor is 1/2 in or 13mm, that a rachet is good.and to remove balancer sometimes youll need a puller. hope this helps.

Oct 13, 2009 | 1989 Buick LeSabre

1 Answer

Where do i locate the crank sensor on a 92 buick century? i changer the harmonic balancer and now the car wont start any diagrams or pics would be great!


the crank sensor is located behind the harmonic balancer and give these websites a try www.autozone.com and www.alldatadiy.com if all fails stop by your local library and get your hands on a Haynes auto repair Manual for your car wish you the best of luck michigan Man

Oct 06, 2009 | 1992 Buick Century

1 Answer

How do you remove crank pully on 1990 buick century


Remove any add on pulley extensions, remove center bolt (generally very tight) and use a harmonic balancer puller (that is a specific tool) to get it off.

Sep 10, 2009 | 1990 Buick Century

1 Answer

Locate crank sensor on 1990 buick century


Hello, the crank position sensor or (CPS) censor is located directly behind the harmonic balancer (or fly wheel at the very bottom). The sensor is located on the right side of the harmonic balancer when facing the front of the motor. You must remove the harmonic balancer to replace the sensor. You must also re-align the sensor with 30 thousands of an inch tolorence, or your car may idle rough or may not start. I own a 1990 Buick Century and just replaced my CPS sensor last month. There is a trick I learned to reinstalling the new sensor. Let me know if you need that information.

Apr 06, 2009 | 1990 Buick Century

1 Answer

Cant get balancer off


yes you will need to get a harmonic balancer/ dampener rempoval/installation tool. you usually can rent these tools at your local auto parts store

Nov 08, 2008 | 1991 Buick Century

1 Answer

Harmonic balancer


Check out this link: http://www.autozone.com/addVehicleId,1602402/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c152800cc1e1. This is for a 6 cylinder in your year. This gives you the specs for all of the bolts associated with the crankshaft damper. Good Luck!

Jul 16, 2008 | 1991 Buick Century

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...