Question about Honda Odyssey

Open Question

VSA light and camshaft position sensor - Odyssey Honda Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

davesmith_37
  • 94 Answers

SOURCE: P0340 Code Camshaft Position Sensor


The Camshaft Position (CMP) Sensor detects the position of the camshaft in order to identifiy when piston No. 1 is on its compression stroke. The CMP sensor is used for ignition timing in the Ford DIS igntion system, but not in the EDIS igntion system. Both DIS/EDIS use the CMP signal for synchronizing the firing of sequential fuel injectors.

On the 3.0L vulcan engine, the CMP signal is generated by a single Hall-Effect magnetic switch, activated by a single "vane" spinning around by virture of a synchronized shaft which is driven by the camshaft. 

The CMP sensor & synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Posted on Feb 27, 2009

  • 55 Answers

SOURCE: replacing bad camshaft position sensor

  1. Disconnect battery ground cable.
  2. Remove water pump pulley attaching bolts, then the serpentine belt and water pump pulley.
  3. Disconnect sensor wiring connector and remove sensor retaining bolt.
  4. Twist and pull sensor to remove.
Reverse procedure to install and prior to installing new sensor, lubricate sensor O-ring.

It is located under the water pump. Make sure when you remove the sensor that you rotate the crank shaft and look in the hole to make sure the pick up magnet is still in there. Sometimes they come loose and cause a no start or long crank. You will need to have the code cleared still.

Posted on May 06, 2009

techbuster
  • 5081 Answers

SOURCE: P0340 Camshaft Position Sensor. How do I fix it?

http://www.youtube.com/watch?v=ve1XW5Ul8Os
please go the above link and you have a video procedure for how to change the sensor.
just do it and you are done to drive your car away.

Posted on Aug 09, 2009

  • 1 Answer

SOURCE: camshaft position sensor

The camshaft position sensor is on the rear cylinder head on the left end (the serpentine belt end of the engine - passenger side). It is a son-of-a gun to get at. When it is bad or the connector is intermittant or bad, the symptom will be irregular idle from 500 to 750 RPM or so.

Posted on Aug 22, 2009

  • 144 Answers

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Posted on Sep 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1336 trouble code ho to solve problem


P1336 Ford P1336 Ford - Crankshaft Position Or Camshaft Position Sensor Input Signal Error Share
0 ' Add Comment Possible causes
- Faulty Crankshaft Position Sensor
- Faulty Camshaft Position Sensor
- Crankshaft Position Sensor harness is open or shorted
- Crankshaft Position Sensor circuit poor electrical connection
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
What does this mean? When is the code detected?
The Engine Control Module (ECM) has detected a synchronization or signal error from the cam or crank sensors
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall
- Engine difficult to start
P1336 Ford Description
The input signal to the powertrain control module (PCM) from the crankshaft position (CKP) sensor or the camshaft position (CMP) sensor is erratic.

Read more: http://www.engine-codes.com/p1336_ford.html#ixzz3qT9Hiztc

Nov 03, 2015 | 2005 Ford Freestyle

2 Answers

2007 honda accord. VSA and ABS lights stay lit when the car is on. lights do not blink and the switch to turn on VSA doesn't do anything when pressed now.


VSA and ABS use anti-lock brake sensors to complete the calculation.

The first thing to check is to make sure all 4 of the ABS sensors are clean.

Go to your local car wash and clean the wheels first.
KEY OFF / then reconnect the VSA sensor.

Pull the OBDII and email it to me.

Jan 16, 2014 | Honda Accord Cars & Trucks

1 Answer

Camshaft position sensor


Possible causes
- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery


Read more: http://engine-codes.com/p0367.html#ixzz2o8f0YhiK

Dec 21, 2013 | Cars & Trucks

1 Answer

P 0340 VECTRA 120CP


P0340 - Camshaft Position Sensor 'A' Circuit Malfunctionxicon.jpghttp://engine-codes.com/p0340.htmlForum CodePossible causes- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery Tech notes Sometimes and in some models, low battery voltage or a weak starter can can trigger a Camshaft Position Sensor code.
When is the code detected?The camshaft position sensor signal is not detected by the Engine Control Module(ECM) during the first few seconds of engine crankingSymptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine StallP0340 Description The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module(ECM) to control ignition and fuel injection. The camshaft position sensor senses the retraction of camshaft (intake) to identify a particular cylinder. The camshaft position sensor senses the piston position. The sensor system consists of a rotating part, typically a disc, as well as a static part, the actual sensor.

Jul 06, 2012 | Cars & Trucks

2 Answers

2004 acura tl not shifting stuck on 3rd gear and check engine light and VSA light comes on. but okay after engine shut off and start up again


Somehow it is effecting the TPS (Throttle position sensor) This is the only input to go to third to fouth and not seeing the proper gear change VSA light appears.

Mar 20, 2012 | 2004 Acura TL

1 Answer

Got code po340 on 2008 Chrysler PT cruiser. Runs great sometimes when engine light on & rough at other times like not getting gas. Engine light does not come on every day either. Cam sensor or timing...


P0340: Camshaft Position Sensor A - Bank 1 Circuit Malfunction

- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Feb 08, 2012 | 2008 Chrysler Pt Cruiser

1 Answer

My car is showing PO344 (Camshaft Position Sensor A Circuit Intermittent) as a problem it's having... I replaced the camshaft sensor about 2 years ago when I was having a similar problem; could the sensor...


All ways, the camshaft position sensor signal sent to the ECM is intermittent

The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Powertrain Control Module (PCM) or Electronic Control Module(ECM) to control ignition and fuel injection. The camshaft position sensor senses the retraction of camshaft (intake) to identify a particular cylinder. The camshaft position sensor senses the piston position. The sensor system consists of a rotating part, typically a disc, as well as a static part, the actual sensor.

When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.

When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals.

Check thos DTC diagnostic and possible solutions about P0344 - Camshaft Position Sensor Circuit Intermittent

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall

Possible causes
- Harness or connectors (The sensor circuit is open or shorted)
- Camshaft position sensor may be faulty
- Camshaft (Intake) may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead (Weak) battery

Possible solution
- Charge battery
- Repair harness or connector
- Replaced Camshaft Position Sensor.
Tech notes
- Sometimes and in some models, low battery voltage or a weak starter can can trigger a Camshaft Position Sensor code.


Hope this helps.

Mar 27, 2011 | Dodge Stratus Cars & Trucks

2 Answers

Can u tell me what the problem of this code PO340


I have a 1999 BMW 740 il My SES light came on so I hooked up my OBD code reader p0340 - Camshaft Position Sensor Circuit Malfunction is what came up. so I went to the BMW parts department and bought the Camshaft Position Sensor.
I Replaced the with the new. My SES light was still on so I hooked up the OBD reader again hoping it may reset my SES light but it didn't what did happen is the OBD reader came up with the same code (p0340 - Camshaft Position Sensor Circuit Malfunction) witch is what I just replaced. now I'm at a loss. I'm not sure how to reset my SES light and if I just replaced the Camshaft Position Sensor why dose it the OBD code p0340 still come up. Any suggestions?

Mar 18, 2011 | 1996 Nissan Altima

2 Answers

Toyota ipsum 2002 check light comes on with code P1346.


Definition of Diagnostic Trouble Code P1346 Audi: Ignition Coil Power Output Stage 3 Short to B+ BMW: Misfire During Start Cylinder 3 Buick: Intake Camshaft Position [CMP] Sensor System Performance Cadillac: Intake Camshaft Position [CMP] Sensor System Performance Chevrolet: Intake Camshaft Position [CMP] Sensor System Performance Ford: Fuel Level Sensor B Circuit GMC: Intake Camshaft Position [CMP] Sensor System Performance Lexus: VVT Sensor Rang/Performance Problem (Bank 1) Lincoln: Fuel Level Sensor B Circuit Mazda: Fuel Level Sensor B Circuit Mercury: Fuel Level Sensor B Circuit Oldsmobile: Intake Camshaft Position [CMP] Sensor System Performance Pontiac: Intake Camshaft Position [CMP] Sensor System Performance Saturn: Intake Camshaft Position [CMP] Sensor System Performance Toyota: VVT Sensor /Camshaft Position Sensor Circuit Range/ Performance Problem (Bank 1) Volkswagen: Ignition Coil Power Output Stage 3 Short to B+

Mar 12, 2010 | 2001 Toyota Sienna

2 Answers

2006 Honda crv, vsa, abs, and triangle light are permanently on


You are talking about the VSA activation indicator (triangle with exclamation point in the middle):
This indicator has three functions:

It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.

It flashes when VSA is active.

It comes on along with the VSA system indicator (the rectangle with VSA in it) if there is a problem with the VSA system.

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position.

Hope this helps you understand the problem.

Dec 09, 2009 | 2006 Honda CR-V

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...