Question about 2001 Ford Focus
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: replace number plate bulb
I'm assuming you mean the rear license plate bulb?
Depends on if you have a coupe, sedan, or wagon.
Here's a link to the owner's manual. Start on page 247 and use the procedure that's right for you Focus type:
Posted on May 03, 2009
SOURCE: replace headlight
Review this guide...
Fig. 1: Examples of various types of automotive light bulbs
Fig. 2: Exploded view of the front headlight assembly and related components
Fig. 3: If equipped, open the headlight access panel by sliding the latch and lifting the panel upwards
Fig. 4: Exploded view of the headlight bulb, retainer and wire harness plug
- Open the vehicle's hood and secure it in an upright position
- If necessary, open the bulb access panel by depressing the latch then lifting.
Fig. 5: To remove the bulb, grasp the retainer and rotate it counterclockwise to unlock it ...
Fig. 6: ... then withdraw the bulb from the headlight lens housing
- Unfasten the locking ring which secures the bulb and wire harness plug assembly, then withdraw the assembly rearward.
- Disconnect the electrical wire harness plug from the bulb and remove the locking ring as well.
Fig. 7: Unplug the wire harness from the bulb and either slide the retainer over the plug, or remove it from the bulb
- Before connecting a light bulb to the wire harness plug, ensure that all electrical contact surfaces are free of corrosion or dirt.
- Install the locking ring onto the bulb, then line up the replacement headlight bulb with the harness plug. Firmly push the bulb onto the plug until the spring clip latches over the bulb's projection.
Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation.
- Position the headlight bulb and secure it with the locking ring.
- To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. (If this is a combination low and high beam bulb, be sure to check both intensities.) If the replacement light bulb does not illuminate, either it too is faulty or there is a problem in the bulb circuit or switch. Correct if necessary.
- Close the bulb access panel and the vehicle's hood.
Good luck... and remember rated my help!
Posted on Aug 07, 2009
Open the hatch and look to the side of the housing, there should be a tab sticking out of the side of the assembly with a screw securing it in place (It's between the trim seal and the assembly). Then in the inside of the hatch, look up to where the assembly would be, and there should be a long cylindrical nut (it's made of plastic and will have a metal center for the threads). Remove this and then you can pull the entire assembly off. You won't have a lot of room though because the wires are relatively short.
Posted on Oct 19, 2009
Most of this solution for changing a headlamp on a ford focus sedan is taken from solution 2's writeup, accept with a few more details that should help changing the bulb assembly for the novice. Pop the hood. At the front of the car, look to the back of the
headlight assembly. There will be a plastic cover on the back. On some
models, you need to unscrew the plastic cap; on others, it just pops or
Remove the plastic cover and then take note of the orientation of the three prong connector on the back of the bulb assembly. This is important because the replacement bulb assembly is going to have to be positioned in the same manner. By noting the orientation before taking out the old assembly, it will be easier to orient the replacement bulb assembly after removal.
There is a small retaining clip that surrounds and holds the bulb in place. Removing the clip can be tricky. On my 2003 Ford Focus sedan, there is a special place to push and release the clip that is above the bulb - perhaps further above than you might think. Push the release clip and it will release the retaining clip from the bulb assembly. Gently pull the retaining clip down and out of the way of the bulb assembly. Pull the original bulb straight out. Remove the three prong connector from the bulb assembly. Connect the three prong connector to the replacement bulb and then orient the three prong connector as the original and push bulb assembly straight back into place. Jiggle the assembly slightly to seat it into the correct position in the headlamp housing and replace the retaining clip to hold the bulb in place. Replace the plastic cover on the back of the headlamp and replacement is complete.
No tools. 10 minutes.
Posted on Jan 18, 2010
you did not state which engine you have but if you are not real handy and/or have experience this is not one you should tackle as your first alternator because...
all will require that you either drop the rear of the subframe or rotate the engine forward to remove the alternator.
everything else is the same...remove the belt, unbolt and remove
about an hour job with experience and two hours if a first time
Posted on Apr 03, 2010
Tips for a great answer:
Jan 11, 2016 | 2007 Ford Explorer Sport Trac
Jan 10, 2011 | 2008 Ford Focus
Aug 26, 2010 | 2003 Ford Focus
brian_au no 1 solution is wrong.. globe is under a spring clip cover . remove cover, then unplug, then release retaining spring behind the globe. replacement is just process reversal
Sep 18, 2009 | 2005 Ford Focus
May 20, 2009 | 2004 Ford Focus
Nov 23, 2008 | 2002 Ford SVT Focus
Oct 03, 2008 | 2001 Ford Focus
58 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: