Question about Nissan 300ZX

Open Question

P1220 code on 1996 nissan 300zx tt

The fuel pump control module and fuel pump have been replaced. Signal from the PCM to the ECM has been verified good at the connector to the ECM. The ECM test good. HELP.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
1beertap
  • 32 Answers

SOURCE: PCM module, ECM module 1996 Chevy Suburban K model

Powertrain Control Module = under right side of dash, near blower motor.
Engine Control Module = same as above
Vehicle Control Module = same as above

All Suburban vehicles are equipped with only one of these choices. Good luck.

Posted on Oct 04, 2008

Ad
mechanicm639
  • 253 Answers

SOURCE: replaced TH700R4 on 1988 c/k1500.now cruise

I would look at the wiring around the bellhousing first to be sure you have not pinched any wires. On that truck, behind the glove box is the PCM, and another white colored box called a DRAC. The DRAC controls the speedometer not the PCM. Look into replacing it. Also check your trans and gauge fuses. Good Luck.

Posted on May 06, 2009

  • 52 Answers

SOURCE: 02 dodgeram 2500 4x4 manual

the Cummins ECM communicates to a dodge VECM thats what codes you have. Cummins should not send any voltage over 5vdc to ANY sensor. If all wiring and sensors are good the Cummins ECM may have a bad driver. Only a Cummins ENSITE trouble shooting tech can narrow this down for sure. Sorry to tell ya!!

Posted on Dec 01, 2009

ftw1952
  • 10319 Answers

SOURCE: no power to fuel pump could it be pcm or ecm

check the oil pressure sending unit
upon starting the fuel pump runs off a wire from the oil sender until proper oil pressure is achomplished. then the relay takes over from there

Posted on Mar 11, 2010

  • 14036 Answers

SOURCE: 1987 nissan 300zx stops pumping fuel and cuts off

if fuse and relay good sound like fuel pump going out.

Posted on May 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

O5 Colorado got the ecm code when I shut off the truck and now it won't turn over


What ECM code ? What is everything else that is working ? Headlamps , inside lighting , radio etc... When you turn the key on do the instrument cluster warning lights come on then off a few seconds later ? Anti-theft (security light ) On ? Flashing ? Do you know what all is involved ,or happens when you turn the key to start ?
Circuit Description (ECM/PCM Controlled)
Moving the ignition switch to the START position sends a 12-volt signal to the engine control module (ECM)/powertrain control module (PCM) Crank Request circuit. The ECM/PCM verifies that the transmission is in the PARK or NEUTRAL position. With the transmission in Park, voltage flows through the Park/Neutral position switch and feeds the starter relay coil. The PCM then grounds the control circuit of the starter relay. When the starter relay is energized it allows battery positive voltage to the starter solenoid S terminal. On some vehicles the starter will continue to crank the engine with the key released until it starts or the crank command has timed out to prevent excessive heat build up in the starter circuitry or the ECM/PCM receives an engine run flag.
Circuit Description (BCM Controlled)
Moving the ignition to the START position signals the body control module (BCM) that engine crank has been requested. The BCM verifies that theft is not active and sends a serial data message to the powertrain control module (PCM) requesting engine start. The BCM also energizes the RUN/CRANK RELAY. When the RUN/CRANK RELAY switch side closes, and the vehicle is in Park or Neutral or with the clutch is fully depressed, if equipped, supplies voltage to the starter relay coil. The PCM verifies the transmission is in Park or Neutral and the clutch is fully depressed, if equipped. The PCM will then ground the control circuit of the starter relay, closing the switch supplying voltage to the starter solenoid. On some vehicles the starter will continue to crank the engine with the key released until it starts of the crank command has timed out to prevent excessive heat build up in the starter circuitry or the PCM receives an engine run flag.


Verify that no starter relay, immobilizer, or automatic transmission DTCs are set that would cause the PCM to disable starting.
? If the specified DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle .
Ignition ON, observe the scan tool PCM Ignition 1 Signal parameter with a scan tool. The reading should be greater than 10.0 Volts.
? If less than the specified value, test the ETC, PCM 1, and PCM B fuses, the RUN/CRNK relay, and the PCM ignition voltage circuits for an open/high resistance. If the circuits test normal, replace the PCM.
Ignition OFF, remove the START relay.
Verify that a test lamp illuminates between the B+ circuit terminal 30 and ground.
? If the test lamp does not illuminate, test the START fuse and the B+ circuit for an open/high resistance.
Ignition ON, transmission in Park or clutch pedal pressed, verify that a test lamp illuminates between the PNP/clutch start switch signal circuit terminal 86 and ground.
? If the test lamp does not illuminate, test the IGN fuse, RUN/CRANK relay, PNP/clutch switch ignition voltage circuit, and the signal circuit for a short to ground or an open/high resistance. If the circuits test normal, test or replace the PNP switch or the clutch start switch.
Connect a test lamp between the park/neutral signal circuit terminal 86 and the relay coil control circuit terminal 85.
Ignition ON, transmission in Park, or clutch pedal pressed, turn the ignition switch between the START and RUN positions. The test lamp should turn ON and OFF when changing between the commanded states.
? If the test lamp is always ON, test the relay control circuit for a short to ground. If the circuit tests normal, replace the PCM.
? If the test lamp is always OFF, test the relay control circuit for a short to voltage or an open/high resistance. Test the PNP/clutch start switch signal circuit for an open/high resistance. If the circuits test normal, replace the PCM.
Install the START relay.
Connect a test lamp between the starter solenoid terminal and ground.

Mar 12, 2017 | Cars & Trucks

1 Answer

Mi problem its po371 howcan I fix my problem my car is 2002 nissan altima 2.5


What does this mean?OBD Code P0371 refers to the optical sensor which provides a high resolution signal to the Powertrain Control Module (PCM) by counting pulses on the sensor disk located in the injection pump. The high resolution is one of the most important inputs by the PCM for fuel control and timing. This test monitors the number of high resolution pulses which have been missed (not detected). It's based on a comparison between the number of pulses that were detected since the last pump cam pulse and the number of the pulses that should have occurred. There are approximately 64 high resolution pulses for every cam pulse. SymptomsPossible sumptoms of OBD code P0371
- Engine Light ON (or Service Engine Soon Warning Light) CausesPossible causes of OBD code P0371
- Open or short in the optical sensor circuit - Optical sensor connector - Damaged optical sensor - Damaged PCM or ECM The Error code is generally activated on detection of the following conditions: There are too many high resolution pulses from the optical sensor to the PCM Possible Solutions- If damage, repair optical sensor circuit - Replaced optical sensor - Replaced PCM or ECM

Sep 28, 2012 | 2002 Nissan Altima

1 Answer

Code P0113-P0183


DTC P0113 - Intake Air Temperature Circuit High Input.The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 volt reference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 check engine light code.


DTC P0183 - Fuel Temperature Sensor Circuit High Voltage.


I suggest to check wire connections.

Apr 13, 2012 | 2005 Nissan Quest 3.5

1 Answer

1998 buick park avenue ultra changed fuel pump fuses good relay good pump not working does pcm control this function if so is there a test i can perform to check


PCM stands for Pulse Code Modulation. Pulse-code modulation (PCM) is a method used to digitally represent sampled analog signals. It is the standard form for fuel injection computers. A PCM stream is a digital representation of an analog signal, in which the magnitude of the analog signal is sampled regularly at uniform intervals, with each sample being quantized to the nearest value within a range of digital steps. So no, Pulse Code Modulation does not control the fuel pump. The Fuel Injection Computer does control the fuel pump via a relay. Bad connection between the fuel pump relay and the in-tank fuel pump, or a bad fuel pump.

Jan 12, 2012 | 2000 Buick LeSabre

1 Answer

Codes p0351 miss and is goverened at 2800 rpms.


P0351 is Ignition Coil A Primary/Secondary Circuit Malfunction.
Possible causes: - Open or short in the ignition coil circuit - Ignition coil circuit shorted to ground - Ignition coil connector - Damaged ignition coil - Damaged PCM or
Possible solution - If damage, repair ignition coil circuit - Replaced ignition coil - Replaced PCM or ECM When is the code detected? The test fails when the Powertrain Control Module (PCM) or Electronic Control Module(ECM) does not receive a valid pulse signal from the ignition coil.
P0351 Description: The ignition signal from the Powertrain Control Module (PCM) or Electronic Control Module(ECM) is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil secondary circuit.
Hope this helps :)

Mar 07, 2011 | 2002 Dodge Intrepid

1 Answer

Trac off light came on and off then stayed on while driving, p0203p0204 p0300 codes when scanned with little machine better read open circuts in both injectors loss of power


P0203 - Injector Circuit Malfunction Cylinder 3

Powertrain Control Module (PCM) or Electronic Control Module (ECM) checks the injectors circuit resistance and monitors the voltage drop during normal operation. The PCM/ECM will trigger the P0203 code when the resistance or voltage drop at the injector #3 is out of specifications.

Causes:
- Open or shorted wiring harness to the injector #3
- Bad injector #3
- Bad PCM/ECM

Solutions:
- If damage, repair injector wire harness or connector
- Replace injector
- Replace PCM or ECM


P0204 - Injector Circuit Malfunction Cylinder 4

Same info as the P0203 DTC


P0300 - Random/Multiple Cylinder Misfire Detected

When a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the crankshaft position (CKP) sensor (POS) signal to vary, Powertrain Control Module (PCM) or Electronic Control Module (ECM) can determine that a misfire is occurring.

Causes:
- Improper spark plug
- Insufficient compression
- Incorrect fuel pressure
- The injector circuit is open or shorted
- Fuel injectors may be faulty
- Intake air leak
- The ignition signal circuit is open or shorted

Solutions:
- Perform Injector Service
- Replace Spark Plugs
- Replace Injectors
- Replace Ignition Coils

Feb 03, 2011 | 2001 Pontiac Sunfire

2 Answers

Code p0605. 2006 f 150


Powertrain Definition: Internal Control Module Read Only Memory (ROM) Error P0605 FORD Description The ECM consists of a microcomputer and connectors for signal input and output and for power supply. The ECM controls the engine.
Most common cause of this code is a defective ECM (Electronic Control Module), in your year the part is known as the PCM (Powertrain control module)

Jan 27, 2011 | 2006 Ford F-150

2 Answers

I have on 01 xterra-service engine light on-codes P1126 & P0325. I think the battery is about to go,could it be realated to codes? Otherwise what do the codes mean? Appreciate any help


Your battery has nothing to do with these codes. Your vehicles computers have detected a malfunction or failure in the system. This triggers these codes and sets your check engine light. Below I have listed the code meanings and some repair solutions.

P1126 - Throttle Position (Narrow Range) Sensor Circuit Malfunction.

Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle control motor relay is ON/OFF controlled by the ECM. When the ignition switch is turned ON, the ECM sends an ON signal to throttle control motor relay and battery voltage is provided to the ECM. When the ignition switch is turned OFF, the ECM sends an OFF signal to throttle control motor relay and battery voltage is not provided to the ECM.

Possible Causes For P1126:
- Harness or connectors (Throttle control motor relay circuit is open)
- Throttle control motor relay


P0325 - Knock Sensor Circuit Malfunction

The knock sensor is attached to the cylinder block. It senses engine knocking using a piezoelectric element. A knocking vibration from the cylinder block is sensed as vibrational pressure. This pressure is converted into a voltage signal and sent to the Powertrain Control Module (PCM) or Electronic Control Module (ECM).

Possible Causes For P0325:
- Knock sensor circuit short to ground.
- Knock sensor circuit short to power.
- Knock sensor circuit open.
- Damaged knock sensor.
- Damaged PCM or ECM

Possible Solutions:
- Repair or resecure harness or connector
- Replace knock sensor Bank 1 (Bank 1 if applicable)
- Replace PCM or ECM

The P0325 DTC is a very common problem with Nissan vehicles. On most Nissan vehicles the knock sensor is located on top of the engine block.

knock_sensor_infiniti.gif

Jan 20, 2011 | 2001 Nissan Xterra

1 Answer

Honda accord incorrect gear ratio code p0370


Honda P0370 - Timing Reference High Resolution Signal A Malfunction.

The optical sensor provides a high resolution signal to the Powertrain Control Module (PCM) by counting pulses on the sensor disk located in the injection pump. The high resolution is one of the most important inputs by the PCM for fuel control and timing. This test monitors the number of high resolution pulses which have been missed (not detected). It's based on a comparison between the number of pulses that were detected since the last pump cam pulse and the number of the pulses that should have occurred. There are approximately 64 high resolution pulses for every cam pulse.

Possible Causes:
- Open or short in the optical sensor circuit
- Optical sensor connector
- Damaged optical sensor
- Damaged PCM
- Damaged ECM

Possible Solutions:
- If damaged repair the optical sensor circuit
- Replace optical sensor
- Replace PCM
- Replace ECM

Not sure where you got incorrect gear ratio. This P0370 DTC is for what I have listed above.

Jan 19, 2011 | 1998 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...