Question about 2001 Ford Explorer Sport Trac

Open Question

2003 ford explorer sport trac P0403 code - 2001 Ford Explorer Sport Trac

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: 2007 FORD EXPLORER SPORT TRAC 4X4 Change oil light on

Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.

The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
following:
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
NEW OIL”.
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.

Posted on Apr 02, 2009

  • 148 Answers

SOURCE: Ball joint replacement-2003 Ford Sport Trac

if you dont have a ball joint press and dont know how to use one then dont do it, but if you do its not that bad of a job just jack the truck up under the control arm remove the brake rotor then take the lower ball joint nut off then use a pickle fork to break the ball joint loose then take the axle nut off push the axle out of the bearing and use the ball joint press to remove and replace the ball joint

Posted on Jul 19, 2009

billandrade
  • 6 Answers

SOURCE: P2195 CODE ON 2003 FORD EXPLORER SPORT TRAC 4.O

Hello,
Very common concern with the Explorer, Explorer Sport Trac and Ranger with the 4.0l SOHC engine! The upper and lower intake manifold gaskets fail, causing vacuum leaks..It can be Extremely difficult to detect these leaks, because they only leak intermittently (usually in the AM after a cold soak)... As the engine warms up they seal back up! Sometimes the vehicle will idle rough, surge or stall after initial start up, then the symptoms will clear after it gets to operating temperature... Usually there will be no driveability symptoms at all, except the engine light coming on and setting lean codes.. The gaskets have been redesigned to correct this concern..


Bill Andrade Ford Master Technician/ASE Master Technician

Posted on Sep 22, 2009

  • 1 Answer

SOURCE: 01 ford explorer sport trac rear timing chain diagram

They will not loan you the tools.....how else will they continue to rip off the average garage junkie and make lots of money?

Posted on Nov 18, 2009

  • 18 Answers

SOURCE: how do i reset the check engine light on my 2003

Unplug the battery for about 10 min then plug it back up start the engine. the computer should reset, if the light comes back on then u still have problems.

Posted on Jan 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 sport trac multiple codes


Hi Daniel , so what are the codes ? an what would you like to know ? What you should do etc...

Apr 28, 2015 | 2003 Ford Explorer Sport Trac

1 Answer

How to clean the MAF for a ford explorer sport trac 2003


there is no cleaning of this with solvents of any kind it will contaminate the sensor. you can blow it out with air but if it is acting up and setting a code replace it. hope this helps

Jan 31, 2011 | 2003 Ford Explorer Sport Trac

1 Answer

Trying to find the door key code for a ford explorer sport trac 2003


You will have to take this one to the dealer. they can retrieve the code or put a new one in for you. call around because some of them will do it for free.
Randy

Nov 09, 2010 | 2003 Ford Explorer Sport Trac

2 Answers

I need fuse box diagram for 2003 ford explorer sport trac


go to 2003 ford explorer owners manual and download it for free from ford then go to roadside emergencies and you will find the fuse box and power distribution box diagram for all fuses

Dec 16, 2009 | 2003 Ford Explorer Sport Trac

1 Answer

P2195 CODE ON 2003 FORD EXPLORER SPORT TRAC 4.O SOHC. I CHANGED OUT ALL THREE OXYGEN SENSORS, AS ADVISED, AND STILL COMING UP WITH P0171, P0174, AND NOW P2195. HAVE ALSO CHECKED ELECTRICAL CONNECTIONS,...


Hello,
Very common concern with the Explorer, Explorer Sport Trac and Ranger with the 4.0l SOHC engine! The upper and lower intake manifold gaskets fail, causing vacuum leaks..It can be Extremely difficult to detect these leaks, because they only leak intermittently (usually in the AM after a cold soak)... As the engine warms up they seal back up! Sometimes the vehicle will idle rough, surge or stall after initial start up, then the symptoms will clear after it gets to operating temperature... Usually there will be no driveability symptoms at all, except the engine light coming on and setting lean codes.. The gaskets have been redesigned to correct this concern..


Bill Andrade Ford Master Technician/ASE Master Technician

Sep 22, 2009 | 2003 Ford Explorer Sport Trac

1 Answer

What is code 51 on a 2005 ford explorer sport trac


What kind of code is that? Normally OBD-II codes are in the format p0051 or p1051. I'm going to guess it's a p0051?

Apr 10, 2009 | 2003 Ford Explorer Sport Trac

1 Answer

Sport trac


there should be a diagram in your handbook

Aug 31, 2008 | 2003 Ford Explorer Sport Trac

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...