Question about Cars & Trucks

Open Question

What are the settings to torque a 1.1 peugeot 106 head bolts up?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
mironate
  • 19 Answers

SOURCE: torque settings

  1. Tighten the cylinder head bolts sequentially in three steps. NOTE: Perform each step twice. 1st step torque: 39 Nm (4.0 kgf-m, 29 ft. lbs.) 2nd step torque: 69 Nm (7.0 kgf-m, 51 ft. lbs.) 3rd step torque: 98.1 Nm (10.0 kgf-m, 72.3 ft. lbs.) Use a beam-type torque wrench. When using a preset-type torque wrench, be sure to tighten slowly and not to overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt, and retighten it from the first step.

Posted on Aug 06, 2008

Ad
  • 4 Answers

SOURCE: head bolts torque settings

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Posted on Feb 07, 2009

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

martin538
  • 117 Answers

SOURCE: need head bolt torque settings for 200 landrover discovery 4.0 liter 241 cu.in.

Stage 1 20nm
Stage 2 +90 degrees
Stage 3 +90 degrees

Posted on Apr 13, 2009

  • 2 Answers

SOURCE: Head bolt torque settings for peugeot 206 1100cc

haynes manual

Posted on Jun 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cylinder head bolt torque specs 2005 peugeot 307 1.6


try asking a service center if you can photo copy the page or use phone take pis of the page. if not try library

Feb 24, 2015 | 2005 Peugeot 307 1.6

1 Answer

Help please What torque are the cylinder head bolts on peugeot expert 1.6 hdi 2008 i need to put the head back on


no problem the correct setting is ,hmm it says tighten to 20nm then 40nm and then slacken off 130? and tighten 130? ,well this the proverbial brown stuff from a cow to me as when i do these engine i pull down with a speed key then a rachet then my 80cm snap on bar so i suppose iam pulling down to around 75/80 lbs per inch but in all honesty i never use a torque wrench as i used to torque heads in ford of dagenham at 18yrs old so three engine a minute i just sort of feel for the bolt stretch and that it really .

May 03, 2011 | Peugeot Liberte Cars & Trucks

1 Answer

What is the torque number sequence for a 2001 oldsmobile aurora 3.5 v6


Assuming about cylinder head...

zjlimited_947.jpg

Fig. Front cylinder head bolt torque sequence - 3.5L (VIN H) engine
  1. Install the cylinder head with a new gasket.
  2. Install new M11 bolts and M6 bolts.
  3. Torque the M11 bolts in sequence to:
    1. Step 1: 30 ft. lbs. (40 Nm).
    2. Step 2: 100 degree turn.
    3. Step 3: 100 degree turn.

  4. Torque the long M6 bolt to 22 ft. lbs. (30 Nm).
  5. Torque both shorter M6 bolts to 106 inch lbs. (12 Nm).
  6. Install or connect the following:
    Lifters Rocker arms Camshafts Primary chain
  7. Remove the timing chain holding tool.
  8. Install or connect the following:
    Camshaft covers. Torque the bolts to 80 inch lbs. (9 Nm). Exhaust manifold. Torque the bolts to 22 ft. lbs. (30 Nm). Coolant crossover pipe. Torque the bolts to 18 ft. lbs. (25 Nm). Intake manifold. Torque the bolts to 62 inch lbs. (7 Nm). New oil filter Negative battery cable

Hope helps.

Mar 29, 2011 | 2001 Oldsmobile Aurora

1 Answer

What is the toqrque spechs and order for a Northstar 4.6 engin for both head and main & rod barngs. Does the main barnings have a order


If you have to pull a cylinder head on a 1993-1999 4.0L or 4.6L Northstar V8 to replace a gasket or do a valve job, do not reuse the old 11mm head bolts. Also, GM has revised the head bolt torque values and tightening procedure as follows:
  1. In sequence, torque all bolts to 30 ft.-lbs.
  2. In sequence, rotate all bolts an additional 70 degrees.
  3. In sequence, rotate all bolts an additional 60 degrees.
  4. In sequence, rotate all bolts another 60 degrees.
  5. Torque the front three M6 head bolts to 106 in.-lbs.

Dec 09, 2010 | 2003 Cadillac Seville

1 Answer

Torque in a 97cadi heads?


use new bolts step 1 30 ftlbs
step 2 70 degrees
step 3 another 60 degrees
step 4 another 60 degrees
190 degrees total for the m11-10 bolts
the m6-3 bolts 106 inch lbs
tighten in seqence
<-----front rear bank
73159
106248
----->front bank
95137
842810

Jul 16, 2010 | 1997 Cadillac DeVille

1 Answer

Need to know torque specifications for intake heads and cylinder heads


Heads
Step 1 - 24 ft.lbs
Step 2 - 45 ft.lbs
Step 3 - 65 ft.lbs
Apply sealant to head bolt threads.

Lower intake
Step 1 - 27 inch lbs
Step 2 - 106 inch lbs
Step 3 - 133 inch lbs

Upper intake
Step 1 - 44 inch lbs
Step 2 - 88 inch lbs

Jan 23, 2010 | 1999 Chevrolet Blazer

1 Answer

Torque setting for peugeot 206


hallo
If you have normal 1.6 liter 206:
max bolt lenght:176,5mm
20Nm and aditional 240°

1,6 liter 16valve engine
max bolt lenght:122,6mm
20Nm and aditional 260°

Marko

Sep 25, 2009 | 2006 Peugeot 504

1 Answer

Mr K.Williams


hallo
if you mean road wheels 90 Nm
rear hub (center bolt) 140 Nm
Marko

Sep 21, 2009 | Peugeot Cars & Trucks

1 Answer

Looking for the torque specs for 1998 chevy astro van?


1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)
2811243.jpg


exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)

cbb8861.jpg

thanks for your vote !

Dec 28, 2008 | 1998 Chevrolet Astro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

947 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...