Question about 2002 Toyota Tundra

Open Question

Fuel door won't open

Door has a lock, no internal release. Key goes in fine, and will turn 2 or 3 degrees, but that is as far as it will go.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: passenger door lock jammed

Your door latch assembly may be compromised. It could be rusted, the electric solenoid (if it has one) may be seized. Or the rods from the key are bent. Are you using th key in this door regularly? If not, the tumblers in the lock may be seized. Spray some WD-40 in the lock where the key goes, and jam the key in & out repeatedly, and retry. Remove the door panel & spray the interior of the latch, also. Hope this works for you; or, you are going to need new latches.

Posted on Sep 09, 2008

Ad
bad_dog1
  • 104 Answers

SOURCE: drivers door power lock wont work.

Either the wring going to that motor or the motor itself is bad.

Posted on Mar 09, 2009

  • 201 Answers

SOURCE: 98 camry door lock will not turn....

really sounds like the tumbler pins are stuck in the cylinder of the lock. mite want to spray some lubricant like(PB Blaster)or WD-40 in the cylinder key hole and push key in and out to see if tumblers will release..gd luck..chris

Posted on May 13, 2009

jmgldsmth
  • 1889 Answers

SOURCE: 2004 Camry front driver door lock will only lock/unlock with key

Remove the door panel and reconnect the plug going to the front driver door lock or, if you can hear the motor trying to engage the door lock cam when you press the lock/unlock remotereconnect the door lock lever bar

Posted on Jun 09, 2009

  • 13 Answers

SOURCE: can not lock car by key remote . toyota rav 4 53 plate

If your car has an alarm with a separate remote, it is a separate system and it is probably self-arming. When you lock the doors with the key central lock, the alarm gets armed by the RAV4 being OFF and the door locking action. When you unlock the doors with the key, the alarm is still armed because the key is not comunicating with the alarm just the cars factory keyless system.

Posted on Apr 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vw golf mk4 my rear passenger door willnot open with central locking key system. i can't even open it from the inside, pull the door handle and the lock pin rises but door won't open. i believ


This worked for me on 2008 Mk5 Golf, after the rear passenger door would not open fro outside or inside.

Hold the inside door latch open and keep it extended, then with the key fob open and close the door locks (still holding the inside latch open). Keep locking and unlocking the door, then it made a kluck and it released.

Mar 23, 2013 | Volkswagen Golf Cars & Trucks

1 Answer

2000 cadillac deville driver side won't open with the key


1) Key turns but dose not unlock door. This means that the rod that goes to the back of the lock has came off. This also means that is the reason door is not unlocking with the remote as it pops the lock rod inside the door which pushes the lock open.
2) Key does not turn lock at all but works passengers side door. This means that the locks has been changed in the door, but that doesn't sound like the problem as you say the remote doesn't open the drivers side door so more than likely the rod has came off the back of the lock

Nov 07, 2012 | Cars & Trucks

1 Answer

Key won't turn clockwise...


it,s probley the lock cyl.

Jun 12, 2012 | Cars & Trucks

1 Answer

How to syncronize 2 keyless remotes for 2000 gmc sierra


Here is the way to do it.
1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.
4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.
10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.
11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

May 25, 2012 | 2000 GMC Sierra

1 Answer

My gas door is locked and won't open on my 2001


Inside the truck behind the trim is a manual release for the gas door, the release looks like the head of a large key on a small wire string. It is marked.

Feb 10, 2012 | 2001 Volvo S60

2 Answers

2003 Monte Carlo SS, FOBS won't unlock doors (new batterries), use key and open the door with the door open FOB will lock and unlock the door, shut the door and the FOB won't lock the doors. After...


If the passkey is messed up, there will be a light on the dash that says security, or have a picture of a car with a lock thru it. If there is no light when the key is turned forward, then its NOT a passkey problem.



tayjoejoe_35.jpgtayjoejoe_36.jpg

Aug 17, 2011 | 2003 Chevrolet Monte Carlo

1 Answer

Mercedes c class 2001 elegance, key fob not working everytime its pressed. I have had the batteries checked and they are still working fine, any advice as to what is causing this?


Most likely needs to be re matched to the car.

Two bits of info off the net for you

C CLASS (1993-1997), E CLASS (1995-1997), SLK (1996-)
Procedure
1. Point the remote control at the receiver - this should be located in the driver's door handle or next to the boot lock button.
2. Press the lock/unlock button.
3. Within 30 seconds manually lock or unlock the vehicle using the passenger's door lock or the boot lock.
Alternative method
Procedure
1. Point the remote control at the receiver - this should be located in the driver's door handle or next to the boot lock button.
2. Press the lock/unlock button.
3. Within 30 seconds, switch the ignition ON.
Alternative method
Procedure
1. Point the remote control at the receiver - this should be located in the driver's door handle or next to the boot lock button.
2. Press the lock/unlock button.
3. Within 30 seconds, turn the ignition switch to position II.


and

1. Place key in ignition lock and turn to position 2 [all ignition lights on]
2: Turn key to off position and remove from ignition.
3. Within 10 seconds:
3a: press the Close [Lock] button and hold it down
3b: while the Close button is still depressed simultaneously press the Open [Unlock] button. Press and release the Open button 5 times [still holding the Close button down]
3c: Release both the Close and the Open buttons at the same time, and immediately push any of the two Open buttons once [i.e. either the Open doors or the Open Tailgate]

This information is for the resetting of a previously synchronised key to match the security system after batteries have been removed or replaced. This information does not work with new keys which it seems must be taken to a person with a key synchronisation device [or a super-ripoff-expensive MB dealer]

hope this helps

Aug 13, 2011 | 2002 Jaguar X-Type

1 Answer

Key buttons will not operate locking system,i have changed battery but still no good.use master key,gets me into the car but alarm goes off and also when i attempt to drive it.


I have the same problem kinda. Lost my master key and sent my ecu off with a home made 2 button key to program immobiliser. This key works to start the engin and drive but I cannot get the key to program with the alarm and locking system. You can try the following steps as may work for you.

I can get my car into programming mode after step 1 but step 2 does not work for me. The locks do not go off at all, not once or twice. Battery in remote key is fine as LCD lights red.

Can anyone help please?

Toyota celica 2000 - 2005 remote keyless entry programming guide
STEP 1
1. Key out of the ignition. Open the drivers door , all other doors are closed . Driver door is unlocked

2. Perform these steps within 5 seconds
a. Insert the key into the ignition ( do not turn it ) take key out
b. Insert the key into the ignition ( do not turn it ) take key out

3. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Insert the key into the ignition ( do not turn it ) and pull it out.

4. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Close drivers door.
d. Insert the key into the ignition and leave it in the ignition.
Turn the ignition to on (as far as you can go without turning the engine over ), then back to off .
e. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

STEP 2 (Does not work for me)

6. Perform these steps within 40 seconds
a. Press the lock and unlock buttons on the transmitter simultaneously for 2 seconds
b. Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock then unlock once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b as the remote was not accepted.

7. Open drivers door

Hope this works for you.
Hayley

Oct 03, 2010 | 2000 Toyota Celica

3 Answers

2007 Honda Civic fuel door will not open, my son needs to get gas and the fuel door will not open, what is he to do?


You can get to the latch through the trunk. In the trunk, pull theliner away from the area adjacent to the fuel door. You'll see a blackcable that goes to the fuel door latch behind a metal frame. Reach inand turn the latch mount 90 degrees to release it from the fuel doorframe. Your fuel door will now be open.

For a fix, look at this low cost solution: http://www.instructables.com/id/Fix-Broken-Fuel-Door-Cable-on-Honda-Civic-82170/

I tried it over the weekend. It works great.

Jan 31, 2010 | 2007 Honda Civic GX NGV Sedan

Not finding what you are looking for?
2002 Toyota Tundra Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...