Question about 1999 Mercedes-Benz S-Class

Open Question

Seat belt removal on s320 mercedes, 1999

How do you remove interior parts to get to the front seat belts

Posted by Anonymous on


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: The power seats, power rear shade and power mirrors are not working in my 1997 Mercedes S320

i have same problem on 1997 s420, don't know why it is happening. but you can replace cigar lighter fuse then replace seat/mirrors/steering wheel fuse and all is well. thnx

Posted on Jul 20, 2009

  • 1654 Answers

SOURCE: My drivers side seat belt

Sounds more as if the retraction spring would not be engaged.

There are two springs in the W140 seatbelt. The comfort spring is engaged during driving when the carkey is in the whole and the belt is fastened. As soon as you either pull out the key or press the button of the belt lock, a second retraction spring comes up and pulls the belt harder. Check this by pulling out the key with the seatbelt on. You must feel how it gets tightened, but I believe you won't.

Either the spring is broken or the electromagentic contact engaging the spring doesn't switch. If you are lucky the latter is due to a contact issue under the respective seat. Check plugs under the seat first.

Posted on Dec 29, 2010

  • 3 Answers

SOURCE: to remove the rear seat

I have a same problem. need help

Posted on Jul 14, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Diagram for a 99 Mercedes S320 serpentine belt

Hi Sam,

I've uploaded a few images of the serpentine belt for your S320 Mercedes. I hope you find them helpful. Good luck with your car!



Oct 30, 2016 | Cars & Trucks

1 Answer

Removal of front passenger seat on mercedes C 180 2008 model

Two Female Torx (E-30 i think) located front and rear of the seat slider (move the seat all the way back and then all the forward to expose them. WARNING ***DO NOT HAVE THE IGNITION ON WHEN DISCONNECTING THE ELECTRIC FROM THE SEAT AND SEAT BELT BUCKLE. It would cause the Airbag to be set off.

Oct 14, 2014 | 2008 Mercedes-Benz C 180

1 Answer

Where are the fuses located for the air conditioner in a 2001 pontiac bonneville

The interior fuse box in a Pontiac Bonneville is underneath the backseat on the driver's side.

To remove the rear seat cushion:
1. Pull up on the front of the cushion to release the
front hooks.
2. Pull the cushion up and out toward the front of
the vehicle.

To reinstall the rear seat cushion:

1. Buckle the center passenger position safety belt, then
route the safety belts through the proper slots in the
seat cushion. Don't let the safety belts get twisted.
2. Slide the rear of the cushion up and under the
seatback so the rear - locating guides hook into the
wire loops on the back frame.
3. With the seat cushion lowered, push rearward and
then press down on the seat cushion until the spring
locks on both ends engage.
4. Check to make sure the safety belts are properly
routed and that no portion of any safety belt is
trapped under the seat. Also make sure the seat
cushion is secured.

The battery and main fuse blocks are located
under the rear seat cushion. The battery's ground
terminal and some relay wires are exposed.
To help avoid damage to the battery and wires,
be careful when removing or reinstalling the seat
cushion. Do not remove covers from covered
parts. Do not store anything under the seat, as
objects could touch exposed wires and cause
a short.

Jul 22, 2014 | 2001 Pontiac Bonneville

1 Answer

Mercedes clk convertible seat belt extender does not work ?

Its stuck or the spring is sprung. Remove the panel and access the belt and see what the problem is. Most times (98%) the belt is stuck and only needs to be unstuck. If thats is not it then replace part.

May 22, 2014 | 2003 Mercedes-Benz CLK

1 Answer

Remove female seat belt recepticle

Due to Federal Safety regulations, the normal way for this belt to be secured to the car is by a big bolt which is fastened to the body of the car with a nut that cannot be removed. Often, the anchoring bolt is underneath the carpet, and may require quite a bit of the interior of the car on that side to be removed to gain access.
If you have a junk yard/salvage yard nearby, go there and find out what to do, because cars there should have some seats removed.
Be blessed.

Dec 13, 2013 | 1999 Chevrolet Malibu

1 Answer

1990 mercedes benz 500 SL SRS light on seat belt lock is broken see little springs sticking out car was also in a accident previously will replacing the seat belt latch solve the problem? or do i have to...

it could very well be just the seat belt latch but you really need to see what codes are being set because there could be other issues as well. You need to get the SRS system scanned. I do not know if the seat will need to be removed. If the latch is attached to the seat itself and it most likely is I'd say yes the seat will have to come out. Very easy to do. Move seat in full back position to get front bolts out and full forward position to get rear bolts out and then carefully disconnect all electrical connectors going to the seat.

Dec 23, 2017 | Mercedes-Benz S-Class Cars & Trucks

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?

please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Jun 30, 2009 | 1997 Ford Taurus

1 Answer

The power seats, power rear shade and power mirrors are not working in my 1997 Mercedes S320

Just double check that you havent blown a fuse/or fuses, it may be that simple!

May 26, 2009 | 2002 Mercedes-Benz S-Class

1 Answer

1991 mercedes benz 300ce. When I start the car and buckle the seat belt or belts the warning buzzer comes on and off. I don't know if it is a seat belt problem or an ignition problem. I only have the car...

on the driver,s side under dash there is an audible relay called a seatbelt warnung relay. I would recommend replacing it because by just unplugging it you may experience interior lighting issues. It is a very common problem with that era of mercedes. If you remove the under dash you will be able to locate it by sound with the key on. Unplug it with the key off.

Apr 23, 2009 | 1991 Mercedes-Benz 300 Diesel

Not finding what you are looking for?
1999 Mercedes-Benz S-Class Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

80531 Answers

Joseph Prosser

Level 3 Expert

772 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides